Перейти к публикации
tfoto

Ремонт Antminer S7, S9 (обмен опытом)

Hlorofos

Все полезные ссылки и FAQ можно найти в первом сообщении. Прежде чем задать вопрос, посмотрите там.

Сообщение добавил Hlorofos

Рекомендованные сообщения

Там вроде джампером выставляется режим загрузки с флешки. Либо флеша некорректно скопирована.

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
1 час назад, Хэш сказал:

Флешка то как-раз есть, только она не подхватывается. По крайней мере на обычной контрольке.

 

Что имеется в виду под обычной контролькой?

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

Есть два вида контрольных плат на S9: старая, которая ВВВ с переходной платой, и новая, которая одноплатный вариант. Так какая из двух?

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
10 часов назад, Cheba сказал:

 

S9, наверное?

 

Прошивка с джампером получается T-9+ , а потом можно апдейтить или в Т-9 или в S-9.

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
19 часов назад, Хэш сказал:

Новая.

Пробуйте со старой.

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

Сложного ведь ничего нет - прошивка с сайта , джампер и сетевой кабель . Только комплектом !

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
12.12.2018 в 20:09, Хэш сказал:

Новая.

 

Новая и старая контрольки собраны на разном железе и софт у них не совместим.

 

Нужна "двухэтажная" контролькаPwI1iks.jpg&t=593&c=s28eZrlTYq_XsA

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

Может кому то будет нужна прошивка для тестов плат S9 и T9. Знаю много чего еще можно дабавить но и так норм помогает в ремонте плат.

Repair_s9_t9_fw.tar.gz:

https://ru.files.fm/u/9pdh3nmp

https://dropmefiles.com/NC6P5

https://filecloud.me/tzjjpppd8fgi.html

Screenshot from 2018-12-18 17-54-00.png

Screenshot from 2018-12-18 17-54-30.png

Screenshot from 2018-12-18 17-56-26.png

Screenshot from 2018-12-18 17-58-26.png

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

@alexey7mechanic 

Спасибо за програмульку! Она очень кстати мне!

Буду выявлять чипы которые не работают после погружения асиков в масло. Только один асик заработал в жидкости из шести😞

Вот тест одной, погруженной в жидкость,  неработающей платы :

Скрытый текст

Detect 512MB control board of XILINX
Miner Type = S9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Check chain[7] PIC fw version=0x03
Fix freq=650 Chain[7] voltage_pic=108 value=880
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J8] has 48 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 0 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 1 Chain[J8] has 48 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 2 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 3 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 4 Chain[J8] has 48 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 5 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 6 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 7 Chain[J8] has 49 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 8 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 9 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 10 Chain[J8] has 57 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 11 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 12 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 13 Chain[J8] has 50 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 14 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 15 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 16 Chain[J8] has 56 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry 17 Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
 

Что интересно, вынь ее на воздух, обдувай вентиляторами, и будет она нормально работать! 

А после ресета плат вывливается ошибка чтения RT:(

 

Скрытый текст

get RT hashrate from Chain[7]: (asic index start from 1-57)
Check Chain[J8] ASIC RT error: (asic index start from 1-57)
Done check_asic_reg
do read temp on Chain[7]
Chain[7] Chip[29] TempTypeID=00 middle offset=-42
read failed, old value: Chain[7] Chip[29] local Temp=0
read failed on Chain[7] Chip[29] middle Temp old value:0
Chain[7] Chip[2] TempTypeID=00 middle offset=-42
read failed, old value: Chain[7] Chip[2] local Temp=0
read failed on Chain[7] Chip[2] middle Temp old value:0
Done read temp on Chain[7]
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=7951
 

Как говорится, не заплывайте за буйки:)

Изменено пользователем enichkin

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

Всем привет! Помогите ПЛЗ. лезвие в ремонт или дачик температуры это глючит ? Сразу на новом когда пришёл такая фигня ,Третье лезвие отвалилось. а видео прислали что все 3 при проверке даного асика робят. ПОМОГИТЕ. кто сталкивался с таким. СПАСИБО.

111.png

Изменено пользователем Вladimir

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

@Вladimir  в ремонт... и причем температура, когда у Вас всего два чипа живых..

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

получается пока везли чипы накрылися? их что от пайки отресло при транспортировке.

Изменено пользователем Вladimir

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
21 минуту назад, Вladimir сказал:

получается пока везли чипы накрылися? их что от пайки отресло при транспортировке.

вполне может быть так, пока довезли - рассыпался. Могли видео записать, чтобы Вы увидели что он работает и отправить, хотя на самом деле первая плата и не работала. Возможно вообще платы заменили перед отправкой.

С первой платой у Вас явно проблема.

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
14 часов назад, Вladimir сказал:

Мда. буду отправлять в иркутск.

пока сложность маленькая не отправляйте, а майните на том, что есть, а то потеряете за месяц больше,..

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

отвалились две платы причем одновременно, асик их не видет, перетык и восстановление с сд карты никчему не привели, блок управления вроде рабочий,рабочую карту видит во всех слотах,  чтото не верится что две платы одновременно вышли из строя

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
2 часа назад, kartuka сказал:

отвалились две платы причем одновременно, асик их не видет, перетык и восстановление с сд карты никчему не привели, блок управления вроде рабочий,рабочую карту видит во всех слотах,  чтото не верится что две платы одновременно вышли из строя

попробуйте по одной плате запускать, одна может "просаживать" другую, если результат прежний - две платы вышли из строя.

Прикрепите лог аппарата, если есть возможность, посмотрим информацию там.

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
6 часов назад, Вladimir сказал:

Одну плату отправлю

Не примут, только асик в сборе.  Я как делаю, насобираю и отправляю. Причем ставлю в хлам убитые вентиляторы, некоторые  аж с лопастями на проволочках, и платы в разбой, чуть дороже ремонт, но прокатывает.

Крайний раз прислали абсолютно новый s9j, видимо надоело им с хламом забавляться..

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах
2 часа назад, ASIC REPAIR сказал:

попробуйте по одной плате запускать, одна может "просаживать" другую, если результат прежний - две платы вышли из строя.

Прикрепите лог аппарата, если есть возможность, посмотрим информацию там.

по одной тоже безрезультатно

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty ([email protected]) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]     Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000311] ps7-ttc #0 at df804000, irq=43
[    0.000623] Console: colour dummy device 80x30
[    0.000655] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040208] pid_max: default: 32768 minimum: 301
[    0.040435] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040454] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042635] CPU: Testing write buffer coherency: ok
[    0.042983] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043045] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043265] L310 cache controller enabled
[    0.043285] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121039] CPU1: Booted secondary processor
[    0.210228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210360] Brought up 2 CPUs
[    0.210380] SMP: Total of 2 processors activated.
[    0.210388] CPU: All CPU(s) started in SVC mode.
[    0.211062] devtmpfs: initialized
[    0.213496] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214752] regulator-dummy: no parameters
[    0.223774] NET: Registered protocol family 16
[    0.226048] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.228359] cpuidle: using governor ladder
[    0.228372] cpuidle: using governor menu
[    0.235894] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.237421] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.237434] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.237554] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.259247] bio: create slab <bio-0> at 0
[    0.260845] vgaarb: loaded
[    0.261638] SCSI subsystem initialized
[    0.262550] usbcore: registered new interface driver usbfs
[    0.262724] usbcore: registered new interface driver hub
[    0.262958] usbcore: registered new device driver usb
[    0.263492] media: Linux media interface: v0.10
[    0.263650] Linux video capture interface: v2.00
[    0.263896] pps_core: LinuxPPS API ver. 1 registered
[    0.263907] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.264046] PTP clock support registered
[    0.264406] EDAC MC: Ver: 3.0.0
[    0.265476] Advanced Linux Sound Architecture Driver Initialized.
[    0.268494] DMA-API: preallocated 4096 debug entries
[    0.268509] DMA-API: debugging enabled by kernel config
[    0.268598] Switched to clocksource arm_global_timer
[    0.290491] NET: Registered protocol family 2
[    0.291174] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.291232] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.291317] TCP: Hash tables configured (established 4096 bind 4096)
[    0.291371] TCP: reno registered
[    0.291389] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.291424] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.291679] NET: Registered protocol family 1
[    0.292038] RPC: Registered named UNIX socket transport module.
[    0.292050] RPC: Registered udp transport module.
[    0.292059] RPC: Registered tcp transport module.
[    0.292067] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.292081] PCI: CLS 0 bytes, default 64
[    0.292550] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.294627] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.296772] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.296968] msgmni has been set to 967
[    0.297761] io scheduler noop registered
[    0.297775] io scheduler deadline registered
[    0.297817] io scheduler cfq registered (default)
[    0.308552] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.308574] dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.434457] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.002082] console [ttyPS0] enabled
[    1.006378] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.014032] [drm] Initialized drm 1.1.0 20060810
[    1.031263] brd: module loaded
[    1.040747] loop: module loaded
[    1.050439] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.056193] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.064215] libphy: XEMACPS mii bus: probed
[    1.068581] ------------- phy_id = 0x3625e62
[    1.073492] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.082295] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.089098] ehci-pci: EHCI PCI platform driver
[    1.096320] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.103162] usbcore: registered new interface driver usb-storage
[    1.110077] mousedev: PS/2 mouse device common for all mice
[    1.116174] i2c /dev entries driver
[    1.123114] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.128635] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.134525] Xilinx Zynq CpuIdle Driver started
[    1.139413] sdhci: Secure Digital Host Controller Interface driver
[    1.145510] sdhci: Copyright(c) Pierre Ossman
[    1.149953] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.156692] mmc0: no vqmmc regulator found
[    1.160735] mmc0: no vmmc regulator found
[    1.198615] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.207329] usbcore: registered new interface driver usbhid
[    1.212844] usbhid: USB HID core driver
[    1.217565] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.223864] nand: Micron MT29F2G08ABAEAWP
[    1.227826] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.233776] Bad block table found at page 131008, version 0x01
[    1.240001] Bad block table found at page 130944, version 0x01
[    1.246056] 3 ofpart partitions found on MTD device pl353-nand
[    1.251845] Creating 3 MTD partitions on "pl353-nand":
[    1.256933] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.265006] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.272349] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.281362] TCP: cubic registered
[    1.284603] NET: Registered protocol family 17
[    1.289324] Registering SWP/SWPB emulation handler
[    1.295251] regulator-dummy: disabling
[    1.299649] UBI: attaching mtd1 to ubi0
[    1.677123] UBI: scanning is finished
[    1.689051] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.696103] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.702890] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.709575] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.716413] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.722424] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.729533] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 862493722
[    1.738461] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.747694] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.747699] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.751784] ALSA device list:
[    1.751787]   No soundcards found.
[    1.768535] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.899138] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.905067] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.914200] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    1.924083] UBIFS: reserved for root: 0 bytes (0 KiB)
[    1.929124] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A24A8E1-2021-4A54-8A4E-D8E294AE00E5, small LPT model
[    1.960433] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    1.991434] devtmpfs: mounted
[    1.994547] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    3.061490] random: dd urandom read with 0 bits of entropy available
[    3.688647] 
[    3.688647] bcm54xx_config_init
[    4.298643] 
[    4.298643] bcm54xx_config_init
[    7.299481] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.305575] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   22.029571] In axi fpga driver!
[   22.032642] request_mem_region OK!
[   22.036035] AXI fpga dev virtual address is 0xdf9fc000
[   22.041173] *base_vir_addr = 0xc510
[   22.056737] In fpga mem driver!
[   22.059874] request_mem_region OK!
[   22.063376] fpga mem virtual address is 0xe2000000
[   22.838621] 
[   22.838621] bcm54xx_config_init
[   23.478650] 
[   23.478650] bcm54xx_config_init
[   26.479486] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   26.485504] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  265.822279] random: nonblocking pool is initialized
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=8000c510
miner ID : 8008a48078504814
Miner Type = T9+
AsicType = 1387
real AsicNum = 18
use critical mode to search freq...
get PLUG ON=0x07003f0e
Find hashboard on Chain[1]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Find hashboard on Chain[8]
Find hashboard on Chain[9]
Find hashboard on Chain[10]
Find hashboard on Chain[11]
Find hashboard on Chain[12]
Find hashboard on Chain[13]
set_reset_allhashboard = 0x0000ffff
chain[1] PIC jump to app
Check chain[1] PIC fw version=0x90
chain[2] PIC jump to app
Check chain[2] PIC fw version=0x90
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[1] has freq in PIC and will jump over...
Chain[1] has core num in PIC
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[2] has freq in PIC and will jump over...
Chain[2] has core num in PIC
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[3] has freq in PIC and will jump over...
Chain[3] has core num in PIC
has freq in PIC, will disable freq setting.
chain[8] has freq in PIC and will jump over...
Chain[8] has core num in PIC
has freq in PIC, will disable freq setting.
chain[9] has freq in PIC and will jump over...
Chain[9] has core num in PIC
has freq in PIC, will disable freq setting.
chain[10] has freq in PIC and will jump over...
Chain[10] has core num in PIC
has freq in PIC, will disable freq setting.
chain[11] has freq in PIC and will jump over...
Chain[11] has core num in PIC
has freq in PIC, will disable freq setting.
chain[12] has freq in PIC and will jump over...
Chain[12] has core num in PIC
has freq in PIC, will disable freq setting.
chain[13] has freq in PIC and will jump over...
Chain[13] has core num in PIC
get PIC voltage=33 on chain[1], value=810
get PIC voltage=1 on chain[2], value=930
get PIC voltage=1 on chain[3], value=930
get PIC voltage=33 on chain[8], value=810
get PIC voltage=33 on chain[9], value=810
get PIC voltage=1 on chain[10], value=930
get PIC voltage=1 on chain[11], value=930
get PIC voltage=1 on chain[12], value=930
get PIC voltage=1 on chain[13], value=930
set_reset_allhashboard = 0x00000000
chain[8] temp offset record: 1,-5,0,0,0,0,33,28
chain[8] temp chip I2C addr=0x98
chain[10] temp offset record: 1,-5,0,0,0,0,33,28
chain[10] temp chip I2C addr=0x98
chain[12] temp offset record: 1,0,0,0,0,0,40,28
chain[12] temp chip I2C addr=0x98
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 9, total chain num = 9 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1515 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = T9+
Miner compile time: Fri Nov 24 23:19:16 EST 2017 type: Antminer T9+set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 8008a48078504814
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[5] speed=5880
get fan[2] speed=4320
get fan[5] speed=5880
get fan[2] speed=4320
get fan[5] speed=5880
chain[1] PIC jump to app
Check chain[1] PIC fw version=0x90
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J2] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J2] test patten OK temp=-1
chain[2] PIC jump to app
Check chain[2] PIC fw version=0x90
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J3] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J3] test patten OK temp=-1
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J4] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J4] test patten OK temp=-1
Chain[J9] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J9] test patten OK temp=-1
Chain[J10] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J10] test patten OK temp=-1
Chain[J11] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J11] test patten OK temp=-1
Chain[J12] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J12] test patten OK temp=-1
Chain[J13] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J13] test patten OK temp=-1
Chain[J14] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J14] test patten OK temp=-1
Chain[J2] will use voltage=930 [1] to open core
Chain[J3] will use voltage=930 [1] to open core
Chain[J4] will use voltage=930 [1] to open core
Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Chain[J2] orignal chain_voltage_pic=33 value=810
Chain[J2] will use backup chain_voltage_pic=870 [11]
Chain[J2] get working chain_voltage_pic=11
Chain[J3] orignal chain_voltage_pic=1 value=930
Chain[J3] will use backup chain_voltage_pic=870 [11]
Chain[J3] get working chain_voltage_pic=11
Chain[J4] orignal chain_voltage_pic=1 value=930
Chain[J4] will use backup chain_voltage_pic=870 [11]
Chain[J4] get working chain_voltage_pic=11
Chain[J9] orignal chain_voltage_pic=1 value=930
Chain[J9] will use backup chain_voltage_pic=870 [11]
Chain[J9] get working chain_voltage_pic=11
Chain[J10] orignal chain_voltage_pic=1 value=930
Chain[J10] will use backup chain_voltage_pic=870 [11]
Chain[J10] get working chain_voltage_pic=11
Chain[J11] orignal chain_voltage_pic=1 value=930
Chain[J11] will use backup chain_voltage_pic=870 [11]
Chain[J11] get working chain_voltage_pic=11
Chain[J12] orignal chain_voltage_pic=1 value=930
Chain[J12] will use backup chain_voltage_pic=870 [11]
Chain[J12] get working chain_voltage_pic=11
Chain[J13] orignal chain_voltage_pic=1 value=930
Chain[J13] will use backup chain_voltage_pic=870 [11]
Chain[J13] get working chain_voltage_pic=11
Chain[J14] orignal chain_voltage_pic=1 value=930
Chain[J14] will use backup chain_voltage_pic=870 [11]
Chain[J14] get working chain_voltage_pic=11
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 1 time
Chain[J2] has 18 asic
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 2 time
Chain[J2] has 18 asic
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 3 time
Chain[J2] has 18 asic
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 4 time
Chain[J2] has 18 asic
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 5 time
Chain[J2] has 18 asic
Chain[J3] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 6 time
Chain[J2] has 18 asic
Chain[J3] has 0 asic
Chain[J2] has core num in PIC
Chain[J9] has core num in PIC
Chain[J10] has core num in PIC
miner total rate=3539GH/s fixed rate=3500GH/s
read PIC voltage=930 on chain[1]
Chain:1 chipnum=18
Chain[J2] voltage added=0.0V
Chain:1 base freq=575
Asic[ 0]:575 
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575 
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575 
Asic[17]:575 
Chain:1 max freq=575
Chain:1 min freq=575

read PIC voltage=930 on chain[8]
Chain:8 chipnum=18
Chain[J9] voltage added=0.0V
Chain:8 base freq=575
Asic[ 0]:575 
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575 
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575 
Asic[17]:575 
Chain:8 max freq=575
Chain:8 min freq=575

read PIC voltage=930 on chain[9]
Chain:9 chipnum=18
Chain[J10] voltage added=0.0V
Chain:9 base freq=575
Asic[ 0]:575 
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575 
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575 
Asic[17]:575 
Chain:9 max freq=575
Chain:9 min freq=575


Miner fix freq ...
read PIC voltage=930 on chain[1]
Chain:1 chipnum=18
Chain[J2] voltage added=0.0V
Chain:1 base freq=575
Asic[ 0]:575 
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575 
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575 
Asic[17]:575 
Chain:1 max freq=575
Chain:1 min freq=575

read PIC voltage=930 on chain[8]
Chain:8 chipnum=18
Chain[J9] voltage added=0.0V
Chain:8 base freq=575
Asic[ 0]:575 
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575 
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575 
Asic[17]:575 
Chain:8 max freq=575
Chain:8 min freq=575

read PIC voltage=930 on chain[9]
Chain:9 chipnum=18
Chain[J10] voltage added=0.0V
Chain:9 base freq=575
Asic[ 0]:575 
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575 
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575 
Asic[17]:575 
Chain:9 max freq=575
Chain:9 min freq=575

max freq = 575
set baud=1
Chain[J9] PIC temp offset=1,-5,0,0,0,0,33,28
chain[8] temp chip I2C addr=0x98
Chain[J9] chip[0] use PIC middle temp offset=-5 typeID=55
New offset Chain[8] chip[0] local:25 remote:28 offset:27 
Chain[J9] chip[0] get middle temp offset=27 typeID=55
open core on chain[1] [8] [9]...
set voltage=870 on chain[1], the real voltage=870
Chain[J2] set working voltage=870 [11]
setStartTimePoint total_tv_start_sys=272 total_tv_end_sys=273
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[1]: (asic index start from 1-18)
Asic[01]=61.6390 Asic[02]=69.9440 Asic[03]=69.7090 Asic[04]=63.5350 Asic[05]=72.5610 Asic[06]=66.5550 Asic[07]=61.7560 Asic[08]=64.7430 
Asic[09]=66.4370 Asic[10]=68.0310 Asic[11]=62.9980 Asic[12]=64.8430 Asic[13]=61.3540 Asic[14]=64.2060 Asic[15]=63.6860 Asic[16]=66.7900 
Asic[17]=64.4740 Asic[18]=64.2560 

get RT hashrate from Chain[8]: (asic index start from 1-18)
Asic[01]=66.7390 Asic[02]=62.0920 Asic[03]=69.4070 Asic[04]=65.0780 Asic[05]=62.5950 Asic[06]=64.2560 Asic[07]=66.6720 Asic[08]=69.8090 
Asic[09]=65.1960 Asic[10]=65.9000 Asic[11]=69.2730 Asic[12]=61.9240 Asic[13]=65.8670 Asic[14]=68.6690 Asic[15]=64.8100 Asic[16]=71.1350 
Asic[17]=59.9780 Asic[18]=64.0550 

get RT hashrate from Chain[9]: (asic index start from 1-18)
Asic[01]=64.1720 Asic[02]=62.7800 Asic[03]=67.0750 Asic[04]=67.2260 Asic[05]=70.3300 Asic[06]=68.8200 Asic[07]=66.9910 Asic[08]=65.4140 
Asic[09]=65.4810 Asic[10]=65.1290 Asic[11]=65.0110 Asic[12]=67.7460 Asic[13]=56.9080 Asic[14]=64.6420 Asic[15]=67.6960 Asic[16]=68.4840 
Asic[17]=64.1220 Asic[18]=59.2570 
Check Chain[J2] ASIC RT error: (asic index start from 1-18)
Check Chain[J9] ASIC RT error: (asic index start from 1-18)
Check Chain[J10] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
do read temp on Chain[8]
Chain[8] Chip[1] TempTypeID=55 middle offset=27
Chain[8] Chip[1] local Temp=58
Chain[8] Chip[1] middle Temp=74
Done read temp on Chain[8]
set FAN speed according to: temp_highest=58 temp_top1[PWM_T]=58 temp_top1[TEMP_POS_LOCAL]=58 temp_change=0 fix_fan_steps=0
FAN PWM: 66
read_temp_func Done!
CRC error counter=7388
 

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty ([email protected]) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]     Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000297] ps7-ttc #0 at df804000, irq=43
[    0.000596] Console: colour dummy device 80x30
[    0.000624] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.090242] pid_max: default: 32768 minimum: 301
[    0.090458] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090479] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092596] CPU: Testing write buffer coherency: ok
[    0.092920] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.092978] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.093191] L310 cache controller enabled
[    0.093210] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.170988] CPU1: Booted secondary processor
[    0.260222] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.260351] Brought up 2 CPUs
[    0.260370] SMP: Total of 2 processors activated.
[    0.260378] CPU: All CPU(s) started in SVC mode.
[    0.261037] devtmpfs: initialized
[    0.263430] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.264620] regulator-dummy: no parameters
[    0.272030] NET: Registered protocol family 16
[    0.274318] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.276578] cpuidle: using governor ladder
[    0.276591] cpuidle: using governor menu
[    0.283930] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.285439] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.285452] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.285564] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.306962] bio: create slab <bio-0> at 0
[    0.308370] vgaarb: loaded
[    0.309067] SCSI subsystem initialized
[    0.309955] usbcore: registered new interface driver usbfs
[    0.310123] usbcore: registered new interface driver hub
[    0.310502] usbcore: registered new device driver usb
[    0.311063] media: Linux media interface: v0.10
[    0.311268] Linux video capture interface: v2.00
[    0.311523] pps_core: LinuxPPS API ver. 1 registered
[    0.311535] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.311658] PTP clock support registered
[    0.312025] EDAC MC: Ver: 3.0.0
[    0.313051] Advanced Linux Sound Architecture Driver Initialized.
[    0.315784] DMA-API: preallocated 4096 debug entries
[    0.315798] DMA-API: debugging enabled by kernel config
[    0.315874] Switched to clocksource arm_global_timer
[    0.336847] NET: Registered protocol family 2
[    0.337502] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.337559] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.337644] TCP: Hash tables configured (established 4096 bind 4096)
[    0.337686] TCP: reno registered
[    0.337704] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.337735] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.337968] NET: Registered protocol family 1
[    0.338301] RPC: Registered named UNIX socket transport module.
[    0.338313] RPC: Registered udp transport module.
[    0.338322] RPC: Registered tcp transport module.
[    0.338330] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.338343] PCI: CLS 0 bytes, default 64
[    0.338775] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.340754] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.342816] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.343013] msgmni has been set to 967
[    0.343782] io scheduler noop registered
[    0.343796] io scheduler deadline registered
[    0.343832] io scheduler cfq registered (default)
[    0.354687] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.354707] dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.476497] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.044177] console [ttyPS0] enabled
[    1.048427] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.056073] [drm] Initialized drm 1.1.0 20060810
[    1.072901] brd: module loaded
[    1.082296] loop: module loaded
[    1.091478] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.097256] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.105043] libphy: XEMACPS mii bus: probed
[    1.109570] ------------- phy_id = 0x3625e62
[    1.114294] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.122973] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.129669] ehci-pci: EHCI PCI platform driver
[    1.136931] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.143732] usbcore: registered new interface driver usb-storage
[    1.150652] mousedev: PS/2 mouse device common for all mice
[    1.156767] i2c /dev entries driver
[    1.163609] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.169128] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.174997] Xilinx Zynq CpuIdle Driver started
[    1.179874] sdhci: Secure Digital Host Controller Interface driver
[    1.185987] sdhci: Copyright(c) Pierre Ossman
[    1.190305] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.197181] mmc0: no vqmmc regulator found
[    1.201193] mmc0: no vmmc regulator found
[    1.245912] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.254580] usbcore: registered new interface driver usbhid
[    1.260097] usbhid: USB HID core driver
[    1.264786] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.271076] nand: Micron MT29F2G08ABAEAWP
[    1.275051] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.280993] Bad block table found at page 131008, version 0x01
[    1.287223] Bad block table found at page 130944, version 0x01
[    1.293270] 3 ofpart partitions found on MTD device pl353-nand
[    1.299038] Creating 3 MTD partitions on "pl353-nand":
[    1.304141] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.312189] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.319488] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.328410] TCP: cubic registered
[    1.331645] NET: Registered protocol family 17
[    1.336377] Registering SWP/SWPB emulation handler
[    1.342240] regulator-dummy: disabling
[    1.346566] UBI: attaching mtd1 to ubi0
[    1.870305] UBI: scanning is finished
[    1.881905] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.888988] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.895730] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.902434] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.909292] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.915261] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.922392] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 989509089
[    1.931335] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.940552] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.940558] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.944469] ALSA device list:
[    1.944472]   No soundcards found.
[    1.960873] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    2.015626] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.021696] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.030777] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.040658] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.045681] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 1DBB0DD5-1B78-4864-A9DC-36F1D4ED4753, small LPT model
[    2.057423] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.064130] devtmpfs: mounted
[    2.067256] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.893978] random: dd urandom read with 0 bits of entropy available
[    3.285918] 
[    3.285918] bcm54xx_config_init
[    3.895918] 
[    3.895918] bcm54xx_config_init
[    6.896761] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    6.902848] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   19.717089] In axi fpga driver!
[   19.720160] request_mem_region OK!
[   19.723550] AXI fpga dev virtual address is 0xdf9fc000
[   19.728686] *base_vir_addr = 0xc51a
[   19.743359] In fpga mem driver!
[   19.746766] request_mem_region OK!
[   19.750277] fpga mem virtual address is 0xe2000000
[   20.515890] 
[   20.515890] bcm54xx_config_init
[   21.145924] 
[   21.145924] bcm54xx_config_init
[   24.146738] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   24.152757] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  241.264700] random: nonblocking pool is initialized
Detect 512MB control board of XILINX
Miner Type = T9+
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
chain[1] PIC jump to app
Check chain[1] PIC fw version=0x90
chain[2] PIC jump to app
Check chain[2] PIC fw version=0x90
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[J2] will use voltage=930 [1] to open core
Chain[J3] will use voltage=930 [1] to open core
Chain[J4] will use voltage=930 [1] to open core
Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Fix freq=650 Chain[1] voltage_pic=33 value=810
Fix freq=650 Chain[2] voltage_pic=33 value=810
Fix freq=650 Chain[3] voltage_pic=33 value=810
Fix freq=650 Chain[8] voltage_pic=33 value=810
Fix freq=650 Chain[9] voltage_pic=33 value=810
Fix freq=650 Chain[10] voltage_pic=33 value=810
Fix freq=650 Chain[11] voltage_pic=33 value=810
Fix freq=650 Chain[12] voltage_pic=33 value=810
Fix freq=650 Chain[13] voltage_pic=33 value=810
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J2] has 18 asic
Chain[J3] has 0 asic
Chain[J4] has 0 asic
Chain[J9] has 18 asic
Chain[J10] has 18 asic
Chain[J11] has 0 asic
Chain[J12] has 0 asic
Chain[J13] has 0 asic
Chain[J14] has 0 asic
Chain[J2] has no freq in PIC, set default freq=650M
Chain[J2] has no core num in PIC
Chain[J9] has no freq in PIC, set default freq=650M
Chain[J9] has no core num in PIC
Chain[J10] has no freq in PIC, set default freq=650M
Chain[J10] has no core num in PIC

Miner fix freq ...
read PIC voltage=930 on chain[1]
Chain:1 chipnum=18
Asic[ 0]:681 
Asic[ 1]:681 Asic[ 2]:681 Asic[ 3]:681 Asic[ 4]:681 Asic[ 5]:681 Asic[ 6]:681 Asic[ 7]:681 Asic[ 8]:681 
Asic[ 9]:681 Asic[10]:681 Asic[11]:681 Asic[12]:681 Asic[13]:681 Asic[14]:681 Asic[15]:681 Asic[16]:681 
Asic[17]:681 
Chain:1 max freq=681
Chain:1 min freq=681

read PIC voltage=930 on chain[8]
Chain:8 chipnum=18
Asic[ 0]:681 
Asic[ 1]:681 Asic[ 2]:681 Asic[ 3]:681 Asic[ 4]:681 Asic[ 5]:681 Asic[ 6]:681 Asic[ 7]:681 Asic[ 8]:681 
Asic[ 9]:681 Asic[10]:681 Asic[11]:681 Asic[12]:681 Asic[13]:681 Asic[14]:681 Asic[15]:681 Asic[16]:681 
Asic[17]:681 
Chain:8 max freq=681
Chain:8 min freq=681

read PIC voltage=930 on chain[9]
Chain:9 chipnum=18
Asic[ 0]:681 
Asic[ 1]:681 Asic[ 2]:681 Asic[ 3]:681 Asic[ 4]:681 Asic[ 5]:681 Asic[ 6]:681 Asic[ 7]:681 Asic[ 8]:681 
Asic[ 9]:681 Asic[10]:681 Asic[11]:681 Asic[12]:681 Asic[13]:681 Asic[14]:681 Asic[15]:681 Asic[16]:681 
Asic[17]:681 
Chain:9 max freq=681
Chain:9 min freq=681

max freq = 681
set baud=1
Chain[J9] PIC temp offset=1,-5,0,0,0,0,33,28
Chain[J9] chip[0] use PIC middle temp offset=-5 typeID=55
New offset Chain[8] chip[0] local:23 remote:26 offset:26 
Chain[J9] chip[0] get middle temp offset=26 typeID=55
Chain[J9] chip[128] use PIC middle temp offset=28 typeID=00
Warning: Chain[J9] has no temp offset in PIC! will fix it
New offset Chain[8] chip[0] local:23 remote:27 offset:25 
Chain[J9] chip[0] get middle temp offset=25 typeID=55
New offset Chain[8] chip[32] local:-64 remote:0 offset:-42 
Chain[J9] chip[32] get middle temp offset=-42 typeID=00
open core on chain[1] [8] [9]...
set voltage=810 on chain[1], the real voltage=810
Chain[J2] set working voltage=810 [33]
setStartTimePoint total_tv_start_sys=82 total_tv_end_sys=83
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[1]: (asic index start from 1-18)
Asic[01]=78.8690 Asic[02]=71.6050 Asic[03]=75.6980 Asic[04]=80.7150 Asic[05]=77.1410 Asic[06]=75.6820 Asic[07]=75.0610 Asic[08]=80.6640 
Asic[09]=76.5870 Asic[10]=76.4200 Asic[11]=76.3690 Asic[12]=81.0330 Asic[13]=78.5340 Asic[14]=84.6410 Asic[15]=84.2380 Asic[16]=81.5700 
Asic[17]=81.5540 Asic[18]=78.3660 

get RT hashrate from Chain[8]: (asic index start from 1-18)
Asic[01]=73.9870 Asic[02]=82.3250 Asic[03]=78.7850 Asic[04]=75.2790 Asic[05]=77.7950 Asic[06]=73.8020 Asic[07]=84.3720 Asic[08]=82.4760 
Asic[09]=73.0140 Asic[10]=74.7920 Asic[11]=78.3660 Asic[12]=78.5000 Asic[13]=81.1340 Asic[14]=76.7890 Asic[15]=72.0070 Asic[16]=75.2620 
Asic[17]=74.7250 Asic[18]=79.0030 

get RT hashrate from Chain[9]: (asic index start from 1-18)
Asic[01]=81.7380 Asic[02]=74.7920 Asic[03]=76.6380 Asic[04]=78.6180 Asic[05]=80.3290 Asic[06]=74.5240 Asic[07]=83.1810 Asic[08]=79.5740 
Asic[09]=79.7750 Asic[10]=79.9430 Asic[11]=77.0740 Asic[12]=76.5710 Asic[13]=79.1710 Asic[14]=78.8520 Asic[15]=73.0310 Asic[16]=82.9630 
Asic[17]=78.5000 Asic[18]=81.0170 
Check Chain[J2] ASIC RT error: (asic index start from 1-18)
Check Chain[J9] ASIC RT error: (asic index start from 1-18)
Check Chain[J10] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
do read temp on Chain[8]
Chain[8] Chip[1] TempTypeID=55 middle offset=25
Chain[8] Chip[1] local Temp=71
Chain[8] Chip[1] middle Temp=83
Chain[8] Chip[9] TempTypeID=00 middle offset=-42
read failed, old value: Chain[8] Chip[9] local Temp=0
read failed on Chain[8] Chip[9] middle Temp old value:0
Done read temp on Chain[8]
set FAN speed according to: temp_highest=83 temp_top1[PWM_T]=83 temp_top1[TEMP_POS_LOCAL]=71 temp_change=2 fix_fan_steps=-32
set normal FAN speed...with fix_fan_steps=-32
FAN PWM: 22
read_temp_func Done!
CRC error counter=0

 

Изменено пользователем kartuka

Поделиться сообщением


Ссылка на сообщение
Поделиться на других сайтах

Создайте аккаунт или войдите в него для комментирования

Вы должны быть пользователем, чтобы оставить комментарий

Создать аккаунт

Зарегистрируйтесь для получения аккаунта. Это просто!

Зарегистрировать аккаунт

Войти

Уже зарегистрированы? Войдите здесь.

Войти сейчас

  • Сейчас на странице   0 пользователей

    Нет пользователей, просматривающих эту страницу.

    YoBit.Net
×