Перейти к содержанию

Whatsminer M3


Hlorofos
Сообщение добавил Hlorofos

Все полезные ссылки и FAQ можно найти в первом сообщении. Прежде чем задать вопрос, посмотрите там .

Рекомендуемые сообщения

Так может кто поделиться прошивкой предложенную Utkin? нигде не могу найти....

Ссылка на комментарий
Поделиться на другие сайты

Ну и как прошить этого зверя. Стоит V2

20190404.18.1

Никак не могу понизить. А надо 20180516.10.1. Уже руки опустились...

Ссылка на комментарий
Поделиться на другие сайты

On 3/2/2021 at 5:57 PM, Alexander1010 said:

да это то и из его названия понятно, я имел ввиду хотябы примеры применения (с командами, параметрами и тп) какиенибудь, желательно близкие к моим..

ладно, позже поищу поподробнее..

Есть ли еще наработки? получилось слить образ с платы?

есть контролька  20180516.10.1 с стабильно работающим хешем. есть контролька с 20190404.18, с недохешем. Как же слить прошиву для дальнейшей заливки в другую плату?

Изменено пользователем rusplanet
Ссылка на комментарий
Поделиться на другие сайты

Пробую скопировать файлы через WinSCP. Но файлы атрибут Read only. Подскажите как можно снять атрибут. и заменить файлы?

Ссылка на комментарий
Поделиться на другие сайты

Приветствую всех, может у кого есть рабочий блок питания для даного чуда на продажу

Ссылка на комментарий
Поделиться на другие сайты

Доброго времени! У меня на разных Whatsminer M3X стоят 2 разные прошивки. Одна стандартная с оф сайта, а вот другую не могу найти... Покупал уже с ней. 20180412.18.2 скрин прилагаю

Прошивка.PNG

Ссылка на комментарий
Поделиться на другие сайты

On 6/8/2021 at 9:36 PM, FreeNight1280 said:

Доброго времени! У меня на разных Whatsminer M3X стоят 2 разные прошивки. Одна стандартная с оф сайта, а вот другую не могу найти... Покупал уже с ней. 20180412.18.2 скрин прилагаю

Прошивка.PNG

Вот эту бы прошиву поставить

Ссылка на комментарий
Поделиться на другие сайты

Вот я сам и ищу такую!!!!! Пока безуспешно.... А вытащить ее из рабочего асика нереально.... только путем разбора и приблудами разными..и то не факт, что все получиться

 

Ссылка на комментарий
Поделиться на другие сайты

всем моё почтение господа, вот такая вот штука с вентилятором творится, что делать не имею ни малейшего представления, помогите пожалуйста. желательно подробно)

1.png

Ссылка на комментарий
Поделиться на другие сайты

@professor_preobrazhensky Так контролька не видит скорости вентилятора. Подкиньте любой заведомо исправный с PWM. Если подменного нет, подойдёт даже компьютерный, но чтоб его обороты максимальные были не меньше 3к. Обычно это до 90мм включительно.  Хотя можно и без PWM, по крайней мере на L3,T9,R4 точно работает - главное чтоб с него обороты снимались

У вас вентиляторы оба крутятся? Только проверять надо по отдельности и лучше с демонтажом - если один из вентиляторов выходит на номинал - второй, даже если не работает, входит в аэродинамическое зацепление по первому, и вам кажется, что он работает

Изменено пользователем romariogland
Ссылка на комментарий
Поделиться на другие сайты

  • 2 недели спустя...

@romariogland благодарю Вас за помощь, кулер и правда был не исправен, но после замены вентилятора вообще асик отказался работать, индикаторы не загораются, пробовал перепрошить вообще реакция ноль, завтра попробую разобрать почистить его, была однажды уже проблема такого характера - почистил и заработал. Но вот как-то так в общем-то)

Ссылка на комментарий
Поделиться на другие сайты

@professor_preobrazhensky Вы неисправный на такой же по характеристикам поменяли?

Ссылка на комментарий
Поделиться на другие сайты

купил новый, там видимо что-то с платой на контрольке, оба вентилятора крутят лишь в одном из разъёмов.

@professor_preobrazhensky @romariogland но поставил как Вы и посоветовали (не меньше 3к оборотов) он 3.5 вроде по хар-ам.

Ссылка на комментарий
Поделиться на другие сайты

Контрольку меняй...

 

На Авито ищи по частникам))) фирмы цены лупят)

 

Ссылка на комментарий
Поделиться на другие сайты

@FreeNight1280 ну пока попробую почистить если уж не поможет то конечно буду искать контрольку.

Ссылка на комментарий
Поделиться на другие сайты

@professor_preobrazhensky Если просто запустить - попробуйте подать сигнал RPM на неработающий разьём, вдруг заведётся

Ссылка на комментарий
Поделиться на другие сайты

@romariogland пробовал, он дёргается каждый раз но в ту же секунду прекращает вращение.

@romariogland в не рабочем разъёме рабочий кулер начинает крутит, но прекращает. вот как надо написать)

Ссылка на комментарий
Поделиться на другие сайты

@professor_preobrazhensky что то мне подсказывает, что драйверу/контроллеру просто что то не нравится в этом вентиляторе, либо как они работают в паре

Хотя хз, в руках таких девайсов не держал?‍♂️

Изменено пользователем romariogland
Ссылка на комментарий
Поделиться на другие сайты

@romariogland я как только не пробовал, и отдельно и совместно, и вообще выключал вентиляторы, пока что ничего не помогло, завтра буду шаманить с бубнами пока или не запущу либо не пойму в чём проблема) но пока что ситуация такова и никакова иначе))

@professor_preobrazhensky но большое Вам спасибо за совет, без Ваших отзывов хер бы я самостоятельно дошёл до этого))

Ссылка на комментарий
Поделиться на другие сайты

@romariogland контролька походу полетела, вообще не реагирует. 

@romariogland а как проверить я даже не догадываюсь)

@FreeNight1280 на авито не проверить их целостность к сожалению, а возврат делать никто не будет.

@FreeNight1280 за 3к нашёл я готов ее купить, но если она не рабочая плакали мои 3к, а дарить кому-то свое кровно-нажитое что-то не доставляет мне особого удовольствия.

Ссылка на комментарий
Поделиться на другие сайты

  • 3 недели спустя...

Добрый день.
У меня WhatsMiner M31S_V70. После перезагрузки системы один показал ошибку 561 и теперь встает в ребут каждые 2-3 минуты. Пробовал перегружать удаленно систему и убирать из high mode  - все без изменений. После пары раз стал показывать  еще ошибку 541. Куда копать, так как гугление ничего не дало?596857292_2021-07-1913_21_31.thumb.png.3d998fa931b4effd9b2dabb6e062f403.png

Изменено пользователем Allhailthemole
Ссылка на комментарий
Поделиться на другие сайты

Как сбросить ошибки 

E012
Перегрев процессора (104 C)
Плата управления перезагрузкой
2
Ср, 1 января 18:30:24 CST 2020
Ядро
E003
Slot-1 Temp перегрев (105.00)
Сбросить хеш-плату
9
Вс 1 мар 13:45:56 2020
системный монитор
E006
HS <2,4 т
Перезапустите cgminer
4
Сб 10 июл 20:45:07 MSK 2021
cgminer-монитор
E011
Слот 0 Zero HS 180 секунд
Предупреждение об отсутствии HS
218
Вс 11 июл 14:49:15 2021
системный монитор

Подскажите в чем проблема

an  1 03:00:14 1970 kern.warn kernel: [    4.131366] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support!
Thu Jan  1 03:00:14 1970 kern.info kernel: [    4.164670] EXT4-fs (nandd): mounted filesystem with journalled data mode. Opts: data=journal
Thu Jan  1 03:00:14 1970 kern.info kernel: [    4.207835] EXT4-fs (nandf): mounted filesystem with journalled data mode. Opts: data=journal
Thu Jan  1 03:00:14 1970 kern.warn kernel: [    4.250021] [NAND]nand_ioctl input arg err,cmd=0x4c01.
Thu Jan  1 03:00:14 1970 kern.info kernel: [    4.279677] EXT4-fs (nandf): mounted filesystem with journalled data mode. Opts: data=journal
Thu Jan  1 03:00:14 1970 kern.warn kernel: [    4.320039] [NAND]nand_ioctl input arg err,cmd=0x4c01.
Thu Jan  1 03:00:14 1970 kern.info kernel: [    4.342261] EXT4-fs (nandf): mounted filesystem with journalled data mode. Opts: data=journal
Thu Jan  1 03:00:14 1970 kern.info kernel: [    4.382812] EXT4-fs (nandg): mounted filesystem with journalled data mode. Opts: data=journal
Thu Jan  1 03:00:14 1970 kern.warn kernel: [    4.420025] [NAND]nand_ioctl input arg err,cmd=0x4c01.
Thu Jan  1 03:00:14 1970 kern.info kernel: [    4.441871] EXT4-fs (nandg): mounted filesystem with journalled data mode. Opts: data=journal
Thu Jan  1 03:00:14 1970 user.info kernel: [    4.536977] init: Console is alive
Thu Jan  1 03:00:14 1970 user.info kernel: [    4.541033] init: - watchdog -
Thu Jan  1 03:00:14 1970 user.info kernel: [    4.555006] init: - preinit -
Thu Jan  1 03:00:14 1970 user.info kernel: [    4.641750] procd: - early -
Thu Jan  1 03:00:14 1970 user.info kernel: [    4.645019] procd: - watchdog -
Thu Jan  1 03:00:14 1970 user.info kernel: [    5.273865] procd: - ubus -
Thu Jan  1 03:00:14 1970 kern.notice kernel: [    5.327377] random: ubusd: uninitialized urandom read (4 bytes read, 117 bits of entropy available)
Thu Jan  1 03:00:14 1970 kern.notice kernel: [    5.337767] random: ubusd: uninitialized urandom read (4 bytes read, 117 bits of entropy available)
Thu Jan  1 03:00:14 1970 kern.notice kernel: [    5.347908] random: ubusd: uninitialized urandom read (4 bytes read, 117 bits of entropy available)
Thu Jan  1 03:00:14 1970 kern.notice kernel: [    5.358181] random: ubusd: uninitialized urandom read (4 bytes read, 117 bits of entropy available)
Thu Jan  1 03:00:14 1970 kern.notice kernel: [    5.368304] random: ubusd: uninitialized urandom read (4 bytes read, 117 bits of entropy available)
Thu Jan  1 03:00:14 1970 kern.notice kernel: [    5.378520] random: ubusd: uninitialized urandom read (4 bytes read, 117 bits of entropy available)
Thu Jan  1 03:00:14 1970 kern.notice kernel: [    5.388727] random: ubusd: uninitialized urandom read (4 bytes read, 117 bits of entropy available)
Thu Jan  1 03:00:14 1970 user.info kernel: [    5.399073] procd: - init -
Thu Jan  1 03:00:14 1970 kern.notice kernel: [    5.500365] random: nonblocking pool is initialized
Thu Jan  1 03:00:14 1970 kern.info kernel: [    5.584427] EXT4-fs (nandh): recovery complete
Thu Jan  1 03:00:14 1970 kern.info kernel: [    5.589501] EXT4-fs (nandh): mounted filesystem with journalled data mode. Opts: data=journal
Thu Jan  1 03:00:14 1970 user.notice : Segmentation fault
Thu Jan  1 03:00:15 1970 user.notice : Segmentation fault
Thu Jan  1 03:00:15 1970 kern.warn kernel: [    6.699722] miss config come from efuse!
Thu Jan  1 03:00:15 1970 kern.info kernel: [    6.712644] libphy: gmac0: probed
Thu Jan  1 03:00:15 1970 cron.info crond[1121]: crond (busybox 1.24.2) started, log level 8
Thu Jan  1 03:00:15 1970 kern.info kernel: [    6.789293] sunxi-gmac gmac0 eth0: eth0: Type(1) PHY ID 00441400 at 0 IRQ poll (gmac0-0:00)
Thu Jan  1 03:00:15 1970 daemon.notice netifd: Interface 'lan' is enabled
Thu Jan  1 03:00:15 1970 daemon.notice netifd: Interface 'loopback' is enabled
Thu Jan  1 03:00:15 1970 daemon.notice netifd: Interface 'loopback' is setting up now
Thu Jan  1 03:00:15 1970 daemon.notice netifd: Interface 'loopback' is now up
Thu Jan  1 03:00:15 1970 daemon.notice netifd: Network device 'lo' link is up
Thu Jan  1 03:00:15 1970 daemon.notice netifd: Interface 'loopback' has link connectivity 
Thu Jan  1 03:00:15 1970 authpriv.info dropbear[1163]: Not backgrounding
Thu Jan  1 03:00:15 1970 daemon.err uhttpd[1208]: socket(): Address family not supported by protocol
Thu Jan  1 03:00:15 1970 daemon.notice uhttpd[1208]: skip aging test.
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: HASH_PLUG_PIN0: 15
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: HASH_PLUG_PIN1: 7
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: HASH_PLUG_PIN2: 8
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: Removed /tmp/eeprom_data_out
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: Read Slot-0 EEPROM ret = -1 (Failed)
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: Read Slot-1 EEPROM ret = -1 (Failed)
Thu Jan  1 03:00:15 1970 kern.warn kernel: [    7.344329] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x52)
Thu Jan  1 03:00:15 1970 kern.warn kernel: [    7.369098] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x52)
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: Read Slot-2 EEPROM ret = -1 (Failed)
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: Checking all PCB data, valid slot:
Thu Jan  1 03:00:15 1970 daemon.info detect-eeprom-data[1236]: Total valid slot count = 0
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    7.439315] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x50)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    7.459099] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x50)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    7.479055] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x50)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    7.501682] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x51)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    7.529072] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x51)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    7.551576] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x52)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    7.579072] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x52)
Thu Jan  1 03:00:16 1970 user.notice root: detect-cgminer-config: miner_type=M3 hash_board_version=HB10
Thu Jan  1 03:00:16 1970 user.notice root: detect-cgminer-config: /etc/config/cgminer --> /etc/config/cgminer.m3.v10 remains unchanged
Thu Jan  1 03:00:16 1970 user.notice root: detect-cgminer-config: /etc/config/cgminer.default --> /etc/config/cgminer.default.m3.v10 remains unchanged
Thu Jan  1 03:00:16 1970 user.notice root: detect-cgminer-config: /etc/config/powers --> /etc/config/powers.m3.v10 remains unchanged
Thu Jan  1 03:00:16 1970 user.notice root: detect-cgminer-config: /etc/config/fans --> /etc/config/fans.common remains unchanged
Thu Jan  1 03:00:16 1970 daemon.info keyd[1309]: keyd started.
Thu Jan  1 03:00:16 1970 daemon.info keyd[1309]: RED_LED_PIN: 102
Thu Jan  1 03:00:16 1970 daemon.info keyd[1309]: GREEN_LED_PIN: 103
Thu Jan  1 03:00:16 1970 daemon.info keyd[1309]: RESET_KEY_PIN: 9
Thu Jan  1 03:00:16 1970 daemon.info keyd[1309]: GET_IP_KEY_PIN: 10
Thu Jan  1 03:00:16 1970 daemon.info remote-daemon[1320]: remote-daemon version 1.0 started.
Thu Jan  1 03:00:16 1970 daemon.info system-monitor[1338]: system-monitor v1.5 started. (Platform is ALLWINNER_H3)
Thu Jan  1 03:00:16 1970 daemon.info system-monitor[1338]: Parameters: loop_interval = 3 (s), STATE_LOG_INTERVAL = 86400 (s)
Thu Jan  1 03:00:16 1970 daemon.info system-monitor[1338]: Loaded config file /etc/config/temp_overheat_limit, temp_overheat_limit = 105000
Thu Jan  1 03:00:16 1970 daemon.info system-monitor[1338]: Detecting slots:
Thu Jan  1 03:00:16 1970 daemon.info system-monitor[1338]: Slot-0 is empty. Reset the slot.
Thu Jan  1 03:00:16 1970 daemon.info system-monitor[1338]: Slot-1 is empty. Reset the slot.
Thu Jan  1 03:00:16 1970 daemon.info system-monitor[1338]: Slot-2 has hash board connected.
Thu Jan  1 03:00:16 1970 daemon.info system-monitor[1338]: Detected sensor: lm75 (id=0x75).
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    8.055413] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x50)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    8.099244] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x50)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    8.134123] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x51)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    8.169160] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x51)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    8.204398] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x52)
Thu Jan  1 03:00:16 1970 kern.warn kernel: [    8.239177] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x52)
Thu Jan  1 03:00:16 1970 daemon.notice uhttpd[1208]: --bitmicro-options 1000000:3:63:100:3:384:700:85:105:1:1:90:95:25:528:300:3:000106:8:636:636:636:1:11650:11000:10500:600:0:1:6-4:000107:9:636:636:636:1:11650:11000:10500:600:0:1:6-1:000004:5:576:576:576-2:000105:5:612:612:612 --bitmicro-devs /dev/ttyS1:/dev/ttyS2:/dev/ttyS3 --fans-params 3:0:680:60:4050:100:6000:30-3:0:680:60:4050:100:6000:30 -o stratum+tcp://btc-eu.f2pool.com:3333 -O optcexa.m3-3:21235365876986800 -o stratum+tcp://btc-na.f2pool.com:3333Thu Jan  1 03:00:17 1970 daemon.err system-monitor[1338]: system error state: slot:1, cgminer:1, pool:1, fan:1, temp_sensor:0, temp_over_heat:0, power_supply:0, effective_chips_error:1
Thu Jan  1 03:00:18 1970 daemon.notice netifd: Network device 'eth0' link is up
Thu Jan  1 03:00:18 1970 daemon.notice netifd: Interface 'lan' has link connectivity 
Thu Jan  1 03:00:18 1970 daemon.notice netifd: Interface 'lan' is setting up now
Thu Jan  1 03:00:18 1970 kern.info kernel: [    9.789123] sunxi-gmac gmac0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
Thu Jan  1 03:00:18 1970 daemon.notice netifd: lan (1505): udhcpc: option -h NAME is deprecated, use -x hostname:NAME
Thu Jan  1 03:00:18 1970 daemon.notice netifd: lan (1505): udhcpc (v1.24.2) started
Thu Jan  1 03:00:18 1970 daemon.notice netifd: lan (1505): Sending discover...
Thu Jan  1 03:00:18 1970 daemon.notice netifd: lan (1505): Sending select for 192.168.1.127...
Thu Jan  1 03:00:18 1970 daemon.notice netifd: lan (1505): Lease of 192.168.1.127 obtained, lease time 25200
Thu Jan  1 03:00:18 1970 daemon.notice netifd: Interface 'lan' is now up
Thu Jan  1 03:00:19 1970 daemon.err system-monitor[1338]: system error state: slot:1, cgminer:1, pool:1, fan:0, temp_sensor:0, temp_over_heat:0, power_supply:0, effective_chips_error:1
Thu Jan  1 03:00:21 1970 daemon.notice uhttpd[1208]: ntpd: bad address '0.cn.pool.ntp.org'
Thu Jan  1 03:00:21 1970 daemon.notice uhttpd[1208]: ntpd: could not resolve peer 0.cn.pool.ntp.org, skipping
Thu Jan  1 03:00:24 1970 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.openwrt.pool.ntp.org to 128.0.142.251
Thu Jan  1 03:00:24 1970 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Thu Jan  1 03:00:24 1970 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.asia.pool.ntp.org to 139.199.215.251
Thu Jan  1 03:00:24 1970 daemon.notice uhttpd[1208]: ntpd: sending query to 139.199.215.251
Thu Jan  1 03:00:24 1970 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.pool.ntp.org to 194.190.168.1
Thu Jan  1 03:00:24 1970 daemon.notice uhttpd[1208]: ntpd: sending query to 194.190.168.1
Thu Jan  1 03:00:24 1970 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:+1626725681.110130 delay:0.039027 status:0x24 strat:2 refid:0x0714af59 rootdelay:0.002640 reach:0x01
Thu Jan  1 03:00:24 1970 daemon.notice uhttpd[1208]: ntpd: reply from 194.190.168.1: offset:+1626725681.017692 delay:0.221562 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000000 reach:0x01
Mon Jul 19 23:15:06 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.cn.pool.ntp.org to 84.16.73.33
Mon Jul 19 23:15:06 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 84.16.73.33
Mon Jul 19 23:15:06 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:15:06 2021 daemon.notice uhttpd[1208]: ntpd: timed out waiting for 139.199.215.251, reach 0x00, next query in 1s
Mon Jul 19 23:15:06 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 194.190.168.1
Mon Jul 19 23:15:06 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-0.012403 delay:0.044112 status:0x24 strat:2 refid:0x0714af59 rootdelay:0.002640 reach:0x03
Mon Jul 19 23:15:06 2021 daemon.notice uhttpd[1208]: ntpd: reply from 84.16.73.33: offset:-0.015289 delay:0.079209 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000015 reach:0x01
Mon Jul 19 23:15:07 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 139.199.215.251
Mon Jul 19 23:15:08 2021 daemon.notice uhttpd[1208]: ntpd: reply from 139.199.215.251: offset:-0.030380 delay:0.235813 status:0x24 strat:2 refid:0x04247a64 rootdelay:0.002411 reach:0x01
Mon Jul 19 23:15:09 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 84.16.73.33
Mon Jul 19 23:15:09 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:15:09 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 139.199.215.251
Mon Jul 19 23:15:09 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-0.010100 delay:0.040154 status:0x24 strat:2 refid:0x0714af59 rootdelay:0.002640 reach:0x07
Mon Jul 19 23:15:09 2021 daemon.notice uhttpd[1208]: ntpd: reply from 84.16.73.33: offset:-0.013764 delay:0.079402 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000015 reach:0x03
Mon Jul 19 23:15:09 2021 daemon.notice uhttpd[1208]: ntpd: reply from 139.199.215.251: offset:-0.029535 delay:0.231060 status:0x24 strat:2 refid:0x04247a64 rootdelay:0.002411 reach:0x03
Mon Jul 19 23:15:10 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 84.16.73.33
Mon Jul 19 23:15:10 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:15:10 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-0.009581 delay:0.039663 status:0x24 strat:2 refid:0x0714af59 rootdelay:0.002640 reach:0x0f
Mon Jul 19 23:15:10 2021 daemon.notice uhttpd[1208]: ntpd: reply from 84.16.73.33: offset:-0.011213 delay:0.075041 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000015 reach:0x07
Mon Jul 19 23:15:12 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 139.199.215.251
Mon Jul 19 23:15:12 2021 daemon.notice uhttpd[1208]: ntpd: reply from 139.199.215.251: offset:-0.029741 delay:0.235803 status:0x24 strat:2 refid:0x04247a64 rootdelay:0.002396 reach:0x07
Mon Jul 19 23:15:13 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 84.16.73.33
Mon Jul 19 23:15:13 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:15:13 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-0.008696 delay:0.039422 status:0x24 strat:2 refid:0x0714af59 rootdelay:0.002640 reach:0x1f
Mon Jul 19 23:15:13 2021 daemon.notice uhttpd[1208]: ntpd: reply from 84.16.73.33: offset:-0.015348 delay:0.084823 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000015 reach:0x0f
Mon Jul 19 23:15:15 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 84.16.73.33
Mon Jul 19 23:15:15 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:15:15 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 139.199.215.251
Mon Jul 19 23:15:15 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-0.008488 delay:0.039641 status:0x24 strat:2 refid:0x0714af59 rootdelay:0.002640 reach:0x3f
Mon Jul 19 23:15:15 2021 daemon.notice uhttpd[1208]: ntpd: reply from 84.16.73.33: offset:-0.012660 delay:0.080446 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000015 reach:0x1f
Mon Jul 19 23:15:17 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 84.16.73.33
Mon Jul 19 23:15:17 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:15:17 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-0.006200 delay:0.035980 status:0x24 strat:2 refid:0x0714af59 rootdelay:0.002640 reach:0x7f
Mon Jul 19 23:15:17 2021 daemon.notice uhttpd[1208]: ntpd: reply from 84.16.73.33: offset:-0.003862 delay:0.080326 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000015 reach:0x3f
Mon Jul 19 23:15:22 2021 daemon.notice uhttpd[1208]: ntpd: timed out waiting for 194.190.168.1, reach 0x02, next query in 32s
Mon Jul 19 23:15:31 2021 daemon.notice uhttpd[1208]: ntpd: timed out waiting for 139.199.215.251, reach 0x0e, next query in 33s
Mon Jul 19 23:15:41 2021 cron.err crond[1121]: time disparity of 27112095 minutes detected
Mon Jul 19 23:15:49 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 84.16.73.33
Mon Jul 19 23:15:49 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:15:49 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-0.003621 delay:0.031520 status:0x24 strat:2 refid:0x0714af59 rootdelay:0.002640 reach:0xff
Mon Jul 19 23:15:50 2021 daemon.notice uhttpd[1208]: ntpd: reply from 84.16.73.33: offset:-0.010467 delay:0.083543 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000015 reach:0x7f
Mon Jul 19 23:15:55 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 194.190.168.1
Mon Jul 19 23:15:55 2021 daemon.notice uhttpd[1208]: ntpd: reply from 194.190.168.1: offset:-0.090778 delay:0.223693 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000000 reach:0x05
Mon Jul 19 23:15:55 2021 daemon.notice uhttpd[1208]: Alarm clock
Mon Jul 19 23:15:55 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.cn.pool.ntp.org to 203.107.6.88
Mon Jul 19 23:15:55 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 203.107.6.88
Mon Jul 19 23:16:00 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.openwrt.pool.ntp.org to 128.0.142.251
Mon Jul 19 23:16:00 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:16:05 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.asia.pool.ntp.org to 211.233.84.186
Mon Jul 19 23:16:05 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 211.233.84.186
Mon Jul 19 23:16:05 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.pool.ntp.org to 91.207.136.50
Mon Jul 19 23:16:05 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 91.207.136.50
Mon Jul 19 23:16:05 2021 daemon.notice uhttpd[1208]: ntpd: reply from 203.107.6.88: offset:-5.024079 delay:10.065418 status:0x24 strat:2 refid:0x16fb6d59 rootdelay:0.042466 reach:0x01
Mon Jul 19 23:16:05 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-2.506052 delay:5.058677 status:0x24 strat:2 refid:0x18fb6d59 rootdelay:0.042542 reach:0x01
Mon Jul 19 23:16:05 2021 daemon.notice uhttpd[1208]: ntpd: reply from 211.233.84.186: offset:-0.015398 delay:0.055149 status:0x24 strat:2 refid:0x18fb6d59 rootdelay:0.042115 reach:0x01
Mon Jul 19 23:16:05 2021 daemon.notice uhttpd[1208]: Alarm clock
Mon Jul 19 23:16:10 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.cn.pool.ntp.org to 203.107.6.88
Mon Jul 19 23:16:10 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 203.107.6.88
Mon Jul 19 23:16:15 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.openwrt.pool.ntp.org to 128.0.142.251
Mon Jul 19 23:16:15 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 128.0.142.251
Mon Jul 19 23:16:20 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.asia.pool.ntp.org to 211.233.84.186
Mon Jul 19 23:16:20 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 211.233.84.186
Mon Jul 19 23:16:25 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.pool.ntp.org to 91.207.136.50
Mon Jul 19 23:16:25 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 91.207.136.50
Mon Jul 19 23:16:25 2021 daemon.notice uhttpd[1208]: ntpd: reply from 203.107.6.88: offset:-7.490951 delay:15.014731 status:0x24 strat:2 refid:0x16fb6d59 rootdelay:0.042222 reach:0x01
Mon Jul 19 23:16:25 2021 daemon.notice uhttpd[1208]: ntpd: reply from 128.0.142.251: offset:-4.990080 delay:10.011057 status:0x24 strat:2 refid:0x16fb6d59 rootdelay:0.042222 reach:0x01
Mon Jul 19 23:16:25 2021 daemon.notice uhttpd[1208]: ntpd: reply from 211.233.84.186: offset:-2.497237 delay:5.005860 status:0x24 strat:2 refid:0x18fb6d59 rootdelay:0.042542 reach:0x01
Mon Jul 19 23:16:25 2021 daemon.notice uhttpd[1208]: Alarm clock
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.cn.pool.ntp.org to 203.107.6.88
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 203.107.6.88
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.openwrt.pool.ntp.org to 91.207.136.50
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 91.207.136.50
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.asia.pool.ntp.org to 139.199.215.251
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 139.199.215.251
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: resolved peer 0.pool.ntp.org to 194.190.168.1
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 194.190.168.1
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: reply from 91.207.136.50: offset:+0.016413 delay:0.058302 status:0x24 strat:2 refid:0x18fb6d59 rootdelay:0.030549 reach:0x01
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: reply from 203.107.6.88: offset:+0.007443 delay:0.150128 status:0x24 strat:2 refid:0x5626890a rootdelay:0.012039 reach:0x01
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: reply from 194.190.168.1: offset:-0.075919 delay:0.190718 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000000 reach:0x01
Mon Jul 19 23:16:28 2021 daemon.notice uhttpd[1208]: ntpd: reply from 139.199.215.251: offset:-0.017289 delay:0.227870 status:0x24 strat:2 refid:0x04247a64 rootdelay:0.002411 reach:0x01
Mon Jul 19 23:16:29 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 139.199.215.251
Mon Jul 19 23:16:29 2021 daemon.notice uhttpd[1208]: ntpd: sending query to 194.190.168.1
Mon Jul 19 23:16:29 2021 daemon.notice uhttpd[1208]: ntpd: reply from 194.190.168.1: offset:-0.089136 delay:0.216416 status:0x24 strat:1 refid:0x00535047 rootdelay:0.000000 reach:0x03
Mon Jul 19 23:16:31 2021 daemon.info procd: - init complete -
Mon Jul 19 23:16:31 2021 local0.warn : Started cgminer 4.9.2 git-6089112
Mon Jul 19 23:16:31 2021 local0.notice : bitmicro_get_power_supply_limit, limit_str:3:000106:8:636:636:636:1:11650:11000:10500:600:0:1:6-4:000107:9:636:636:636:1:11650:11000:10500:600:0:1:6-1:000004:5:576:576:576-2:000105:5:612:612:612
Mon Jul 19 23:16:31 2021 local0.notice : bitmicro_get_power_supply_limit, 3:000106:8:636:636:636:1:11650:11000:10500:600:0:1:6:, count:6, id:3, version:0x106, voltage:8, freq:(636 636 636)
Mon Jul 19 23:16:31 2021 local0.notice : params for auto adjusting voltage: enable:1, good HS:11650, HS for sell:11000, HS using highest vol:10500, wait time:600, vol highest:0, vol step:1, freq step:6
Mon Jul 19 23:16:31 2021 local0.notice : bitmicro_get_power_supply_limit, 4:000107:9:636:636:636:1:11650:11000:10500:600:0:1:6:, count:6, id:4, version:0x107, voltage:9, freq:(636 636 636)
Mon Jul 19 23:16:31 2021 local0.notice : params for auto adjusting voltage: enable:1, good HS:11650, HS for sell:11000, HS using highest vol:10500, wait time:600, vol highest:0, vol step:1, freq step:6
Mon Jul 19 23:16:31 2021 local0.notice : bitmicro_get_power_supply_limit, 1:000004:5:576:576:576:, count:6, id:1, version:0x4, voltage:5, freq:(576 576 576)
Mon Jul 19 23:16:31 2021 local0.notice : bitmicro_get_power_supply_limit, 2:000105:5:612:612:612:, count:6, id:2, version:0x105, voltage:5, freq:(612 612 612)
Mon Jul 19 23:16:31 2021 local0.notice : Read power version:0x000106
Mon Jul 19 23:16:31 2021 kern.warn kernel: [  102.207035] sunxi_i2c_do_xfer()974 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x28)
Mon Jul 19 23:16:31 2021 local0.notice : Power voltage has been set to 8
Mon Jul 19 23:16:31 2021 local0.notice : board 0 plug status:1(0: plug, 1: unplug)
Mon Jul 19 23:16:31 2021 local0.notice : board 1 plug status:1(0: plug, 1: unplug)
Mon Jul 19 23:16:31 2021 local0.notice : board 2 plug status:0(0: plug, 1: unplug)
Mon Jul 19 23:16:31 2021 local0.notice : bitmicro: checking for /dev/ttyS3
Mon Jul 19 23:16:31 2021 local0.notice : SM:0: detected /dev/ttyS3: baud:1000000, chain_num:3, chip_num:63, core_num:100 chip_column_num:3
Mon Jul 19 23:16:31 2021 local0.notice : SM:0: chip_freq_limit:636, work_interval:700, temp_limit:85, voltage_limit:8
Mon Jul 19 23:16:31 2021 local0.notice : SM:0: temp_chips:1, temp_sensors_per_chip:1, upfreq_pass_cores_percent:90, upfreq_pass_chips_percent:95
Mon Jul 19 23:16:31 2021 local0.notice : SM:0: pre_heat_temp:25, pre_heat_timeout:300
Mon Jul 19 23:16:31 2021 local0.notice : Fan[0] node count 3, node[0](duty:0, speed:680), node[1](duty:60, speed:4050), node[2](duty:100, speed:6000), freq_times_by_speed:30
Mon Jul 19 23:16:31 2021 local0.notice : Fan[1] node count 3, node[0](duty:0, speed:680), node[1](duty:60, speed:4050), node[2](duty:100, speed:6000), freq_times_by_speed:30
Mon Jul 19 23:16:32 2021 daemon.err system-monitor[1338]: system error state: slot:1, cgminer:0, pool:1, fan:0, temp_sensor:0, temp_over_heat:0, power_supply:0, effective_chips_error:1
Mon Jul 19 23:16:32 2021 local0.notice : Detect fan[0].speed:0
Mon Jul 19 23:16:32 2021 local0.notice : Detect fan[1].speed:6180
Mon Jul 19 23:16:33 2021 local0.notice : Detect fan[0].speed:0
Mon Jul 19 23:16:33 2021 local0.notice : Detect fan[1].speed:6210
Mon Jul 19 23:16:34 2021 local0.notice : Detect fan[0].speed:0
Mon Jul 19 23:16:34 2021 local0.notice : Detect fan[1].speed:6210
Mon Jul 19 23:16:35 2021 local0.notice : Detect fan[0].speed:0
Mon Jul 19 23:16:35 2021 local0.notice : Detect fan[1].speed:6210
Mon Jul 19 23:16:36 2021 local0.notice : Detect fan[0].speed:0
Mon Jul 19 23:16:36 2021 local0.notice : Detect fan[1].speed:6210
Mon Jul 19 23:16:37 2021 local0.notice : Detect fan[0].speed:0
Mon Jul 19 23:16:37 2021 local0.notice : Detect fan[1].speed:6210
Mon Jul 19 23:16:38 2021 local0.notice : Detect fan[0].speed:0
Mon Jul 19 23:16:38 2021 local0.notice : Detect fan[1].speed:6240
Mon Jul 19 23:16:39 2021 local0.notice : Detect fan[0].speed:0
Mon Jul 19 23:16:39 2021 local0.notice : Detect fan[1].speed:6210
Mon Jul 19 23:16:39 2021 local0.warn : fan[0]:detected max fan speed:0 < max speed in fan spec:6000, please check params or repair the fan
Mon Jul 19 23:16:39 2021 local0.notice : fan[0].max_speed_detected:0
Mon Jul 19 23:16:39 2021 local0.notice : fan[1].max_speed_detected:6240
Mon Jul 19 23:16:39 2021 local0.notice cgminer[2033]: SM0: trying OSC frequency 24M
Mon Jul 19 23:16:40 2021 local0.notice cgminer[2033]: fd:4, read_chip_model ret:0 (tried 1 times)
Mon Jul 19 23:16:40 2021 local0.notice cgminer[2033]: SM0: OSC frequency is detected as 24M
Mon Jul 19 23:16:40 2021 local0.notice cgminer[2033]: SM0: open core done, ret:0
Mon Jul 19 23:16:40 2021 local0.notice cgminer[2033]: Probing for an alive pool
Mon Jul 19 23:16:40 2021 local0.notice cgminer[2033]: SM:0, all board pre heat complete, temp_now_max:45.5, pre_heat_temp:25, complete_count:1
Mon Jul 19 23:16:40 2021 local0.notice cgminer[2033]: SM:0, bitmicro_device_reinit
Mon Jul 19 23:16:41 2021 local0.notice cgminer[2033]: SM0: open core done, ret:0
Mon Jul 19 23:16:41 2021 local0.notice cgminer[2033]: fd:4, read_chip_model ret:0 (tried 1 times)
Mon Jul 19 23:16:41 2021 local0.err cgminer[2033]: SM:0, enter test, strategy:0, f_tested:0, f_testing:192, f_limit:636, st_cores:0, st_chips:59
Mon Jul 19 23:16:41 2021 local0.notice cgminer[2033]: Switching to pool 1 stratum+tcp://btc-na.f2pool.com:3333 - first alive pool
Mon Jul 19 23:16:41 2021 local0.notice cgminer[2033]: Pool 1 difficulty changed to 65536
Mon Jul 19 23:16:41 2021 local0.notice cgminer[2033]: Network diff set to 13.7T
Mon Jul 19 23:16:47 2021 local0.warn cgminer[2033]: API running in IP access mode on port 4028 (8)
Mon Jul 19 23:16:49 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:3039 > (2 * speed_get:0), err count:10, threshold:15
Mon Jul 19 23:16:50 2021 daemon.err system-monitor[1338]: system error state: slot:1, cgminer:0, pool:0, fan:0, temp_sensor:0, temp_over_heat:0, power_supply:0, effective_chips_error:1
Mon Jul 19 23:16:52 2021 kern.warn kernel: [  122.953554] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x50)
Mon Jul 19 23:16:52 2021 kern.warn kernel: [  122.977610] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x50)
Mon Jul 19 23:16:52 2021 kern.warn kernel: [  123.000821] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x51)
Mon Jul 19 23:16:52 2021 kern.warn kernel: [  123.027607] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x51)
Mon Jul 19 23:16:52 2021 kern.warn kernel: [  123.050725] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x52)
Mon Jul 19 23:16:52 2021 kern.warn kernel: [  123.077652] sunxi_i2c_do_xfer()974 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x52)
Mon Jul 19 23:16:54 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:2815 > (2 * speed_get:0), err count:0, threshold:15
Mon Jul 19 23:16:59 2021 local0.err cgminer[2033]: SM:0, exit test, strategy:0, f_tested:192, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Mon Jul 19 23:17:04 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:2365 > (2 * speed_get:0), err count:10, threshold:15
Mon Jul 19 23:17:09 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:2197 > (2 * speed_get:0), err count:0, threshold:15
Mon Jul 19 23:17:14 2021 local0.notice cgminer[2033]: Stratum from pool 1 requested work restart
Mon Jul 19 23:17:20 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1860 > (2 * speed_get:0), err count:10, threshold:15
Mon Jul 19 23:17:21 2021 local0.notice cgminer[2033]: Accepted 51e45533 Diff 205K/65536 SM 0 pool 1 
Mon Jul 19 23:17:25 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1691 > (2 * speed_get:0), err count:0, threshold:15
Mon Jul 19 23:17:35 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1523 > (2 * speed_get:0), err count:10, threshold:15
Mon Jul 19 23:17:40 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1523 > (2 * speed_get:0), err count:0, threshold:15
Mon Jul 19 23:17:49 2021 local0.warn cgminer[2033]: Pool 0 stratum+tcp://btc-eu.f2pool.com:3333 alive, testing stability
Mon Jul 19 23:17:49 2021 local0.notice cgminer[2033]: Pool 0 difficulty changed to 65536
Mon Jul 19 23:17:50 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1523 > (2 * speed_get:0), err count:10, threshold:15
Mon Jul 19 23:17:52 2021 local0.warn cgminer[2033]: Pool 0 stratum+tcp://btc-eu.f2pool.com:3333 stable for >120 seconds
Mon Jul 19 23:17:52 2021 local0.warn cgminer[2033]: Switching to pool 0 stratum+tcp://btc-eu.f2pool.com:3333
Mon Jul 19 23:17:55 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1523 > (2 * speed_get:0), err count:0, threshold:15
Mon Jul 19 23:18:05 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1523 > (2 * speed_get:0), err count:10, threshold:15
Mon Jul 19 23:18:08 2021 local0.err cgminer[2033]: SM:0, enter test, strategy:0, f_tested:192, f_testing:384, f_limit:636, st_cores:90, st_chips:59
Mon Jul 19 23:18:10 2021 local0.notice cgminer[2033]: Stratum connection to pool 0 interrupted
Mon Jul 19 23:18:10 2021 local0.notice cgminer[2033]: Pool 0 successfully negotiated resume with the same session ID
Mon Jul 19 23:18:10 2021 local0.notice cgminer[2033]: Pool 0 difficulty changed to 65536
Mon Jul 19 23:18:10 2021 local0.notice cgminer[2033]: Stratum from pool 0 requested work restart
Mon Jul 19 23:18:10 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1523 > (2 * speed_get:0), err count:0, threshold:15
Mon Jul 19 23:18:16 2021 local0.err cgminer[2033]: SM:0, exit test, strategy:0, f_tested:390, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Mon Jul 19 23:18:18 2021 local0.err cgminer[2033]: SM:0, enter test, strategy:0, f_tested:390, f_testing:396, f_limit:636, st_cores:90, st_chips:59
Mon Jul 19 23:18:20 2021 local0.err cgminer[2033]: fan[0] theoretical_speed:1523 > (2 * speed_get:0), err count:10, threshold:15

Эта проблема с м3

Ссылка на комментарий
Поделиться на другие сайты

Скрытый текст

Thu Jul 22 17:46:50 2021 local0.err cgminer[21036]: SM:2, enter test, strategy:0, f_tested:192, f_testing:384, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:46:50 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:192, f_testing:384, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:46:51 2021 local0.err cgminer[21036]: SM:1, enter test, strategy:0, f_tested:192, f_testing:384, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:46:59 2021 local0.notice cgminer[21036]: Stratum from pool 0 requested work restart
Thu Jul 22 17:46:59 2021 local0.err cgminer[21036]: SM:2, exit test, strategy:0, f_tested:390, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:46:59 2021 local0.err cgminer[21036]: SM:0, exit test, strategy:0, f_tested:390, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:00 2021 local0.err cgminer[21036]: SM:1, exit test, strategy:0, f_tested:390, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:01 2021 local0.err cgminer[21036]: SM:2, enter test, strategy:0, f_tested:390, f_testing:396, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:01 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:390, f_testing:396, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:02 2021 local0.err cgminer[21036]: SM:1, enter test, strategy:0, f_tested:390, f_testing:390, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:03 2021 daemon.err uhttpd[1205]: brctl: SIOCGIFBR: No error information
Thu Jul 22 17:47:03 2021 daemon.err uhttpd[1205]: brctl: SIOCGIFBR: No error information
Thu Jul 22 17:47:10 2021 local0.err cgminer[21036]: SM:2, exit test, strategy:0, f_tested:396, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:10 2021 local0.err cgminer[21036]: SM:0, exit test, strategy:0, f_tested:396, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:10 2021 local0.err cgminer[21036]: SM:1, exit test, strategy:0, f_tested:396, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:11 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:396, f_testing:402, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:20 2021 local0.err cgminer[21036]: SM:0, exit test, strategy:0, f_tested:402, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:22 2021 local0.notice cgminer[21036]: Pool 0 difficulty changed to 40000
Thu Jul 22 17:47:22 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:402, f_testing:408, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:30 2021 local0.err cgminer[21036]: SM:0, exit test, strategy:0, f_tested:408, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:31 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:408, f_testing:408, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:34 2021 local0.err cgminer[21036]: SM:2, enter test, strategy:0, f_tested:396, f_testing:396, f_limit:636, st_cores:90, st_chips:59

Скрытый текст

Скрины 

 

Доброго времени. Аналогичная проблема с М3. Большой кусок металлолома. мои логи 

2021-07-20_18-22-09.png

2021-07-20_18-22-42.png

основная панель.png

log.txt

Изменено пользователем alien900
Ссылка на комментарий
Поделиться на другие сайты

Всем доброго дня. Приобрел WhatsMiner M21S. Информация по версии прошивки на скрине.

Есть ли смысл обновлять? Возможно есть альтернативные прошивки. Мне бы сделать его чуть тише.....

WhatsMiner M21S.png

Ссылка на комментарий
Поделиться на другие сайты

22.07.2021 в 17:48, alien900 сказал:
  Показать содержимое

Thu Jul 22 17:46:50 2021 local0.err cgminer[21036]: SM:2, enter test, strategy:0, f_tested:192, f_testing:384, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:46:50 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:192, f_testing:384, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:46:51 2021 local0.err cgminer[21036]: SM:1, enter test, strategy:0, f_tested:192, f_testing:384, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:46:59 2021 local0.notice cgminer[21036]: Stratum from pool 0 requested work restart
Thu Jul 22 17:46:59 2021 local0.err cgminer[21036]: SM:2, exit test, strategy:0, f_tested:390, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:46:59 2021 local0.err cgminer[21036]: SM:0, exit test, strategy:0, f_tested:390, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:00 2021 local0.err cgminer[21036]: SM:1, exit test, strategy:0, f_tested:390, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:01 2021 local0.err cgminer[21036]: SM:2, enter test, strategy:0, f_tested:390, f_testing:396, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:01 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:390, f_testing:396, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:02 2021 local0.err cgminer[21036]: SM:1, enter test, strategy:0, f_tested:390, f_testing:390, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:03 2021 daemon.err uhttpd[1205]: brctl: SIOCGIFBR: No error information
Thu Jul 22 17:47:03 2021 daemon.err uhttpd[1205]: brctl: SIOCGIFBR: No error information
Thu Jul 22 17:47:10 2021 local0.err cgminer[21036]: SM:2, exit test, strategy:0, f_tested:396, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:10 2021 local0.err cgminer[21036]: SM:0, exit test, strategy:0, f_tested:396, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:10 2021 local0.err cgminer[21036]: SM:1, exit test, strategy:0, f_tested:396, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:11 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:396, f_testing:402, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:20 2021 local0.err cgminer[21036]: SM:0, exit test, strategy:0, f_tested:402, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:22 2021 local0.notice cgminer[21036]: Pool 0 difficulty changed to 40000
Thu Jul 22 17:47:22 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:402, f_testing:408, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:30 2021 local0.err cgminer[21036]: SM:0, exit test, strategy:0, f_tested:408, ok_chips:63, ok_cores_min:100, st_cores:90, st_chips:59
Thu Jul 22 17:47:31 2021 local0.err cgminer[21036]: SM:0, enter test, strategy:0, f_tested:408, f_testing:408, f_limit:636, st_cores:90, st_chips:59
Thu Jul 22 17:47:34 2021 local0.err cgminer[21036]: SM:2, enter test, strategy:0, f_tested:396, f_testing:396, f_limit:636, st_cores:90, st_chips:59

  Показать содержимое

Скрины 

 

Доброго времени. Аналогичная проблема с М3. Большой кусок металлолома. мои логи 

2021-07-20_18-22-09.png

2021-07-20_18-22-42.png

основная панель.png

log.txt 113 \u041a\u0431 · 2 downloads

Доброго дня. Решил проблему со своим М3, сняв охлаждение с процесса на плате управления, поставил жидкую терморезину. третий день полет нормальный, 10.5 TH/s стабильно. 

Ссылка на комментарий
Поделиться на другие сайты

Для публикации сообщений создайте учётную запись или авторизуйтесь

Вы должны быть пользователем, чтобы оставить комментарий

Создать учетную запись

Зарегистрируйте новую учётную запись в нашем сообществе. Это очень просто!

Регистрация нового пользователя

Войти

Уже есть аккаунт? Войти в систему.

Войти
  • Последние посетители   0 пользователей онлайн

    • Ни одного зарегистрированного пользователя не просматривает данную страницу
  • Similar Topics

    • Whatsminer m21, m21s

      Здравствуйте, не могу создать SD карту для прошивки Whatsminer m21s. Во время создания флешки нет строчки Bootloader, флешка получается пустая, если вставить в асик то асик не прошивается диоды не светятся. И у кого открывается программа нормально не можете подсказать надписи кнопок в программе. В приложении отображения программы у меня

      в ASIC/FPGA майнеры

    • Контрольная плата whatsminer

      Здравствуйте, подскажите пожалуйста datasheet на микросхемы U5 иU12 на контрольную плату whatsminer или может подскажите где искать boardview на контрольные платы?

      в ASIC/FPGA майнеры

    • Whatsminer M30s++

      Руководство по ремонту хэш-платы для M31S, M31S+, M30S, M30S++, M32 и т. д. Советы требуют вашего внимания: 1. Нормальное рабочее напряжение хэш-платы M3x составляет от 0,31 до 0,32 В * Количество групп (например, 0,31 В * 37 = 11,47 В, т. е. входное напряжение составляет 11,5 В), рекомендуется использовать это в качестве стандарта обслуживания. 2. Рекомендуется использовать осциллограф вместо мультиметра для проверки тактового напряжения. 3. Обеспечьте правильность вышеуказанной рабо

      в ASIC/FPGA майнеры

    • Whatsminer M31, M32

      Есть задача добраться до файлов с логами. чтобы периодически их копировать. Скачали WinSCP и дальше вопросы. как подключаться. Пробовали по порту 443. Вроде подключение есть, но выходит в ошибку. Подскажите как подключение сделать

      в ASIC/FPGA майнеры

    • BiXBiT Dev. кастомные прошивки Whatsminer и Удаленный мониторинг и Контроль: оптимизируйте производительность и эффективность (Devfee от 1% до 2.8%)

      Прошивка для Whatsminer! Разгон для M2x, M3x, M5x серий + Удаленный контроль и Мониторинг для Whatsminer - BiXBiT AMS. + Легкая установка через Whatsminertool + Hotel fee + Даунвольтинг + Прокси сервер + Иммерсионное охлаждение + Контроль и Мониторинг И многое другое!   Инструкция по установке прошивки для Whatsminer:  https://bixbit.io/ru/documentation/rukovodstvo-polzovatelia-whatsminer-asic     Удаленны

      в Прошивки

×
×
  • Создать...