Перейти к содержанию

Antminer D3


Hlorofos
Сообщение добавил Hlorofos

Все полезные ссылки и FAQ можно найти в первом сообщении. Прежде чем задать вопрос, посмотрите там.

Рекомендуемые сообщения

03.08.2018 в 21:32, mir913 сказал:

Всем привет! Возникла проблема с найсхешем.. Стоит несколько д3. Постоянно теряют связь с пулом (dead). Минут 5-15 работают, перестают майнить и уходят в кресты. помогает только ребут. С другими пулами все отлично. Прошивки менял - не помогает.  Остается грешить на пул?


Найсхеш меняет часто добываему монету, что ведет к программному сбою чипов и выпадения их в "хххххх". Спасать будет только ребут.
Без постоянного надзора майнить на найсхеше будет проблематично.

Ссылка на комментарий
Поделиться на другие сайты

07.08.2018 в 11:43, alextj59 сказал:

Начал разбираться с напряжением. На индукторе напряжение 8,5 В на неработающей плате, на работающей 8,1 В. Возможно не работает PIC. Как его проверить?

платы из одного аппарат? одной ревизии?

Ссылка на комментарий
Поделиться на другие сайты

20 часов назад, 13Gat сказал:


Найсхеш меняет часто добываему монету, что ведет к программному сбою чипов и выпадения их в "хххххх". Спасать будет только ребут.
Без постоянного надзора майнить на найсхеше будет проблематично.

Awesome Miner нормально спсправляется с такими задачами.

 

настроил такое, что чипы востанавливались при пониженной частоте и продолжали видется, когда устанавлива частоту нормальную. А сразу при нормальной частоте - чипы не запускались.

 Awesome Miner - см на этом форуме, есть тема такая

Ссылка на комментарий
Поделиться на другие сайты

@Станислав Литовка руками или автоматизацией? - так-то баг известный для этого треша - D3 - но проще или выбрать частоту, на которой стабильно все видит, или забить на отвалившиеся, если их 4-5 штук

Ссылка на комментарий
Поделиться на другие сайты

Подскажите, пожалуйста, в чем может быть проблема - на одной плате исчезло 5 asic чипов на дефолтной частоте 537. Температура нормальная - 70-71 градус, выше не поднимались. Если опустить частоту на один шаг вниз до 531, то на плате появляются все 60 asic чипов. Мне просто интересно чем вызвана данная неисправность и какие дальнейшие варианты ее развития. Спасибо.

Ссылка на комментарий
Поделиться на другие сайты

У меня что-то подобное.

08.08.2018 в 10:39, 13Gat сказал:

Найсхеш меняет часто добываему монету, что ведет к программному сбою чипов и выпадения их в "хххххх". Спасать будет только ребут.
Без постоянного надзора майнить на найсхеше будет проблематично.

Я майню на D3 на найсхеш и без таких инцидентов (вот если действительно проблемы с и-нетом - то вылетает в кресты).

 

Ссылка на комментарий
Поделиться на другие сайты

18 часов назад, iRybin сказал:

@Станислав Литовка руками или автоматизацией? - так-то баг известный для этого треша - D3 - но проще или выбрать частоту, на которой стабильно все видит, или забить на отвалившиеся, если их 4-5 штук

Руками настроил правила, потом автоматизация работает.

по вопросу забить - можно было отдать по гарантии, но этот глюк происходит при перезагрузке и не каждый ра.

на другом Д3 так же бывает выпадают чипы, но там поставил правило - перегрузить и все.

 

 

6 часов назад, gdivochka сказал:

Подскажите, пожалуйста, в чем может быть проблема - на одной плате исчезло 5 asic чипов на дефолтной частоте 537. Температура нормальная - 70-71 градус, выше не поднимались. Если опустить частоту на один шаг вниз до 531, то на плате появляются все 60 asic чипов. Мне просто интересно чем вызвана данная неисправность и какие дальнейшие варианты ее развития. Спасибо.

чем вызвана не знаю, но проблему решил. Как?  см выше. в таком режиме работает с начала лета.

 

Ссылка на комментарий
Поделиться на другие сайты

вот пример что на почту приходит d3-02 только ребут, по D3-01 ребут с изменением частоты...

IMG_5411.PNG

Ссылка на комментарий
Поделиться на другие сайты

По техническим вопросам, вопросам самостоятельного ремонта D3,  кто то встречал обсуждение ?

Ссылка на комментарий
Поделиться на другие сайты

@Triton 

17 минут назад, Triton сказал:

По техническим вопросам, вопросам самостоятельного ремонта D3,  кто то встречал обсуждение ?

тут весь этот раздел практически о самостоятельном ремонте ?
Что именно интересует? ( можно сразу в личку, что бы тут не сорить очередной раз)
А лучше поиском воспользоваться ? 

Ссылка на комментарий
Поделиться на другие сайты

26 минут назад, Triton сказал:

По техническим вопросам, вопросам самостоятельного ремонта D3,  кто то встречал обсуждение ?

Тестер в руки и контрольные напряжения и наличие кз сперва проверить.

Ссылка на комментарий
Поделиться на другие сайты

4 часа назад, Artemka сказал:

Ну как окупились d3 уже? :biggrin:

 

давно

Ссылка на комментарий
Поделиться на другие сайты

Подскажите, что за чип выглядывает из под радиатора ? Маркировка Т250 PK44. Разводка на плате под каждую линейку чипов, но стоит всего два.

ant_D3.jpg

Ссылка на комментарий
Поделиться на другие сайты

9 часов назад, Triton сказал:

Подскажите, что за чип выглядывает из под радиатора ? Маркировка Т250 PK44. Разводка на плате под каждую линейку чипов, но стоит всего два.

ant_D3.jpg

датчик температуры

Ссылка на комментарий
Поделиться на другие сайты

Спасибо, так и предполагал... А какое у него "человеческое" название ? Чем его заменить ? судя по тому, что у него 4 контакта, два из которых земля, это что то вроде терморезистора или p-n переход ?

Ссылка на комментарий
Поделиться на другие сайты

Пытаюсь  починить хеш-плату.

Прошивал альтернативными прошивками и даже иногда она как то начинала работать. - плату видно не было, но хэшрейт от нее был.

 

Но!! Теперь однозначно не работает!

По схемотехнике примерно все понятно. 10 доменов по 6 чипов. Пик контролер посредством которого происходит управление питанием и асиками.

С питанием все ок! На прошивке blissz можно менять напругу - все меняется!

 

Плату достал, подключил и стал щупать чипы на нагрев

55 асик был очень горячий против остальных. Снял его. Он был в КЗ. Купил несколько бу чипов. Сопротивление 40-50 Ом. Поставил. 

 

В процессе экспериментов включил без этого асика. Включать так не стоило. Где то прочитал что возникнет перекос  по питанию и может выбить все чипы в домене.

Походу так и произошло... Теперь стал греться в этом домене 57 асик. Снял его и... он в КЗ

Заменил его и ... после включения 57 асик умер мгновенно. До установки было 50 Ом после установки стало 0 Ом. Че за фигня???

 

Решил поставить официальную прошивку.

Еще раз заменл 57 асик. Не вылетел. И теперь ничего не греется... Все домены звонятся  по 1,1 ом.

В логах плату видно, но асиков нет. Датчика температуры нет и софт все время пытается делать сброс.

лог:

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 65280
[    0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 64768 pages, LIFO batch:15
[    0.000000] AM335X ES1.0 (neon )
[    0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768
[    0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
[    0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 255MB = 255MB total
[    0.000000] Memory: 238676k/238676k available, 23468k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0612cf0   (6188 kB)
[    0.000000]       .init : 0xc0613000 - 0xc06554c0   ( 266 kB)
[    0.000000]       .data : 0xc0656000 - 0xc06cc020   ( 473 kB)
[    0.000000]        .bss : 0xc06cc020 - 0xc0725e3c   ( 360 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000358] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[    0.015440] pid_max: default: 32768 minimum: 301
[    0.015669] Security Framework initialized
[    0.015763] Mount-cache hash table entries: 512
[    0.024593] Initializing cgroup subsys cpuacct
[    0.024625] Initializing cgroup subsys memory
[    0.024686] Initializing cgroup subsys blkio
[    0.024823] CPU: Testing write buffer coherency: ok
[    0.025394] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.025471] Setting up static identity map for 0x8038c820 - 0x8038c86c
[    0.026795] Brought up 1 CPUs
[    0.026819] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[    0.028117] devtmpfs: initialized
[    0.092516] pinctrl core: initialized pinctrl subsystem
[    0.092732] rstctl core: initialized rstctl subsystem
[    0.093224] regulator-dummy: no parameters
[    0.093787] NET: Registered protocol family 16
[    0.094489] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.104162] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
[    0.104347] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.105441] platform 49000000.edma: alias fck already exists
[    0.105476] platform 49000000.edma: alias fck already exists
[    0.105504] platform 49000000.edma: alias fck already exists
[    0.106657] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.106839] OMAP GPIO hardware version 0.1
[    0.108254] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.109571] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.110885] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.111519] of_get_named_gpio_flags exited with status 52
[    0.111549] gpio-rctrl rstctl.3: loaded OK
[    0.116657] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.119855] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.122047] cpsw.0: No hwaddr in dt. Using 3c:a3:08:4a:c7:8a from efuse
[    0.122080] cpsw.1: No hwaddr in dt. Using 3c:a3:08:4a:c7:8c from efuse
[    0.137630] bio: create slab <bio-0> at 0
[    0.149767] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[    0.150012] of_get_named_gpio_flags: can't parse gpios property
[    0.150303] vmmcsd_fixed: 3300 mV 
[    0.153423] SCSI subsystem initialized
[    0.153877] usbcore: registered new interface driver usbfs
[    0.153992] usbcore: registered new interface driver hub
[    0.154323] usbcore: registered new device driver usb
[    0.156425] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
[    0.156459] omap_i2c 4819c000.i2c: unable to select pin group
[    0.156653] media: Linux media interface: v0.10
[    0.156748] Linux video capture interface: v2.00
[    0.156865] pps_core: LinuxPPS API ver. 1 registered
[    0.156881] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.157598] Advanced Linux Sound Architecture Driver Initialized.
[    0.158788] Switching to clocksource gp_timer
[    0.176813] NET: Registered protocol family 2
[    0.177802] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.177891] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[    0.177980] TCP: Hash tables configured (established 2048 bind 2048)
[    0.178072] TCP: reno registered
[    0.178100] UDP hash table entries: 256 (order: 1, 12288 bytes)
[    0.178147] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[    0.178643] NET: Registered protocol family 1
[    0.179233] RPC: Registered named UNIX socket transport module.
[    0.179252] RPC: Registered udp transport module.
[    0.179265] RPC: Registered tcp transport module.
[    0.179279] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.179666] Trying to unpack rootfs image as initramfs...
[    1.941812] Freeing initrd memory: 12240K
[    1.942554] CPU PMU: probing PMU on CPU 0
[    1.942587] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[    1.943129] omap2_mbox_probe: platform not supported
[    1.947006] VFS: Disk quotas dquot_6.5.2
[    1.947244] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.948646] NFS: Registering the id_resolver key type
[    1.948740] Key type id_resolver registered
[    1.948757] Key type id_legacy registered
[    1.948825] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.949255] msgmni has been set to 490
[    1.952127] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.952154] io scheduler noop registered
[    1.952170] io scheduler deadline registered
[    1.952228] io scheduler cfq registered (default)
[    1.956298] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.958731] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[    1.959008] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[    2.619868] console [ttyO0] enabled
[    2.624426] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
[    2.633090] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
[    2.641777] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
[    2.650376] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
[    2.659405] [drm] Initialized drm 1.1.0 20060810
[    2.678063] brd: module loaded
[    2.688354] loop: module loaded
[    2.692586] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
[    2.702521] nand_get_flash_type: 2c,f1 against 2c,f1
[    2.708041] ONFI param page 0 valid
[    2.711714] ONFI flash detected
[    2.715034] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABAEAWP), 128MiB, page size: 2048, OOB size: 64
[    2.726945] omap2-nand: detected x8 NAND flash
[    2.731612] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    2.737194] omap2-nand: using custom ecc layout
[    2.742037] 10 ofpart partitions found on MTD device omap2-nand.0
[    2.748431] Creating 10 MTD partitions on "omap2-nand.0":
[    2.754108] 0x000000000000-0x000000020000 : "spl"
[    2.760912] 0x000000020000-0x000000040000 : "spl_backup1"
[    2.768369] 0x000000040000-0x000000060000 : "spl_backup2"
[    2.775752] 0x000000060000-0x000000080000 : "spl_backup3"
[    2.783168] 0x000000080000-0x000000240000 : "u-boot"
[    2.791375] 0x000000240000-0x000000260000 : "bootenv"
[    2.798329] 0x000000260000-0x000000280000 : "fdt"
[    2.804942] 0x000000280000-0x000000780000 : "kernel"
[    2.815969] 0x000000800000-0x000001c00000 : "root"
[    2.839440] 0x000001c00000-0x000003000000 : "config"
[    2.863190] OneNAND driver initializing
[    2.868924] usbcore: registered new interface driver asix
[    2.874735] usbcore: registered new interface driver cdc_ether
[    2.880982] usbcore: registered new interface driver smsc95xx
[    2.887101] usbcore: registered new interface driver net1080
[    2.893127] usbcore: registered new interface driver cdc_subset
[    2.899418] usbcore: registered new interface driver zaurus
[    2.905424] usbcore: registered new interface driver cdc_ncm
[    2.912154] usbcore: registered new interface driver cdc_acm
[    2.918114] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.926494] Initializing USB Mass Storage driver...
[    2.931734] usbcore: registered new interface driver usb-storage
[    2.938035] USB Mass Storage support registered.
[    2.943075] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    2.949790] musb-hdrc musb-hdrc.0.auto: pdev->id = 0
[    2.955033] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.963804] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.963826] musb-hdrc: MHDRC RTL version 2.0 
[    2.963841] musb-hdrc: setup fifo_mode 4
[    2.963869] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.964016] musb-hdrc musb-hdrc.0.auto: *** mode=3
[    2.969060] musb-hdrc musb-hdrc.0.auto: *** power=250
[    2.975074] musb-hdrc musb-hdrc.1.auto: pdev->id = 1
[    2.980321] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.989092] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.989113] musb-hdrc: MHDRC RTL version 2.0 
[    2.989127] musb-hdrc: setup fifo_mode 4
[    2.989149] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.989289] musb-hdrc musb-hdrc.1.auto: *** mode=1
[    2.994332] musb-hdrc musb-hdrc.1.auto: *** power=250
[    2.999641] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    3.006264] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
[    3.014526] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup
[    3.014631] usb usb1: default language 0x0409
[    3.014690] usb usb1: udev 1, busnum 1, minor = 0
[    3.014714] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.021843] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.029414] usb usb1: Product: MUSB HDRC host driver
[    3.034629] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd
[    3.040296] usb usb1: SerialNumber: musb-hdrc.1.auto
[    3.046301] usb usb1: usb_probe_device
[    3.046329] usb usb1: configuration #1 chosen from 1 choice
[    3.046395] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    3.046598] hub 1-0:1.0: usb_probe_interface
[    3.046620] hub 1-0:1.0: usb_probe_interface - got id
[    3.046648] hub 1-0:1.0: USB hub found
[    3.050654] hub 1-0:1.0: 1 port detected
[    3.054794] hub 1-0:1.0: standalone hub
[    3.054814] hub 1-0:1.0: individual port power switching
[    3.054832] hub 1-0:1.0: no over-current protection
[    3.054849] hub 1-0:1.0: Single TT
[    3.054871] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    3.054891] hub 1-0:1.0: power on to power good time: 10ms
[    3.054946] hub 1-0:1.0: local power source is good
[    3.055059] hub 1-0:1.0: enabling power on all ports
[    3.056157] mousedev: PS/2 mouse device common for all mice
[    3.064123] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[    3.071886] i2c /dev entries driver
[    3.076934] pps_ldisc: PPS line discipline registered
[    3.082405] Driver for 1-wire Dallas network protocol.
[    3.089685] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    3.097252] cpuidle: using governor ladder
[    3.101580] cpuidle: using governor menu
[    3.106177] of_get_named_gpio_flags exited with status 6
[    3.106197] of_get_named_gpio_flags: can't parse gpios property
[    3.106213] of_get_named_gpio_flags: can't parse gpios property
[    3.106250] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[    3.113477] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[    3.120288] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[    3.127510] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[    3.134834] mmc.4 supply vmmc_aux not found, using dummy regulator
[    3.141789] omap_hsmmc mmc.4: pins are not configured from the driver
[    3.155085] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[    3.175110] of_get_named_gpio_flags exited with status -517
[    3.175177] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.182956] ledtrig-cpu: registered to indicate activity on CPUs
[    3.189736] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[    3.196931] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[    3.205028] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[    3.211378] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[    3.218559] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[    3.230830] usbcore: registered new interface driver usbhid
[    3.236749] usbhid: USB HID core driver
[    3.243644] TCP: cubic registered
[    3.247169] Initializing XFRM netlink socket
[    3.251734] NET: Registered protocol family 17
[    3.256612] NET: Registered protocol family 15
[    3.261488] Key type dns_resolver registered
[    3.266121] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    3.274201] ThumbEE CPU extension supported.
[    3.278711] Registering SWP/SWPB emulation handler
[    3.284719] registered taskstats version 1
[    3.291346] of_get_named_gpio_flags exited with status -517
[    3.291421] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.348397] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[    3.354810] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[    3.369317] libphy: 4a101000.mdio: probed
[    3.373630] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[    3.383861] Detected MACID = 3c:a3:08:4a:c7:8a
[    3.388542] cpsw 4a100000.ethernet: NAPI disabled
[    3.393934] of_get_named_gpio_flags exited with status -517
[    3.394001] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.402721] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    3.411982] cpu0 supply cpu0 not found, using dummy regulator
[    3.418491] cpufreq_cpu0: failed to scale voltage up: -22
[    3.424313] cpufreq_cpu0: failed to scale voltage up: -22
[    3.437071] ALSA device list:
[    3.440305]   No soundcards found.
[    3.444874] Freeing init memory: 264K
[    3.448931] Failed to execute /init
[    4.463987] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    5.761817] net eth0: initializing cpsw version 1.12 (0)
[    5.770878] net eth0: phy found : id is : 0x7c0f1
[    5.776329] libphy: PHY 4a101000.mdio:01 not found
[    5.781519] net eth0: phy 4a101000.mdio:01 not found on slave 1
[    8.848893] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
Aug 30 06:20:54 (none) local0.err cgminer: Miner compile time: Mon Nov 20 17:06:56 CST 2017 type: Antminer D3
Aug 30 06:20:54 (none) local0.warn cgminer: Started cgminer 4.9.0
Aug 30 06:20:54 (none) local0.warn cgminer[375]: bitmain_DASH_init
Aug 30 06:20:55 (none) local0.err cgminer[375]: FAN1 too slow ...
Aug 30 06:20:55 (none) local0.err cgminer[375]: FAN2 too slow ...
Aug 30 06:20:55 (none) local0.err cgminer[375]: FAN1 too slow ...
Aug 30 06:20:55 (none) local0.err cgminer[375]: FAN2 too slow ...
Aug 30 06:20:56 (none) local0.err cgminer[375]: FAN1 too slow ...
Aug 30 06:20:56 (none) local0.err cgminer[375]: FAN2 too slow ...
Aug 30 06:20:56 (none) local0.err cgminer[375]: FAN2 too slow ...
Aug 30 06:20:57 (none) local0.err cgminer[375]: FAN2 too slow ...
Aug 30 06:20:57 (none) local0.err cgminer[375]: FAN2 too slow ...
Aug 30 06:20:58 (none) local0.warn cgminer[375]: check_fan_speed OK
Aug 30 06:20:58 (none) local0.notice cgminer[375]: detected at /sys/class/gpio/gpio51/value  chain 0
Aug 30 06:20:58 (none) local0.notice cgminer[375]: detect total chain num 1
Aug 30 06:20:58 (none) local0.notice cgminer[375]: i2c init ok
Aug 30 06:20:58 (none) local0.notice cgminer[375]: check_whether_need_update_pic_program
Aug 30 06:20:59 (none) local0.notice cgminer[375]: reset_PIC16F1704_pic_new ok
Aug 30 06:20:59 (none) local0.notice cgminer[375]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 30 06:21:00 (none) local0.notice cgminer[375]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 30 06:21:00 (none) local0.notice cgminer[375]: every_chain_reset_PIC16F1704_pic_new
Aug 30 06:21:01 (none) local0.notice cgminer[375]: reset_PIC16F1704_pic_new ok
Aug 30 06:21:02 (none) local0.notice cgminer[375]: every_chain_jump_from_loader_to_app_PIC16F1704_new
Aug 30 06:21:02 (none) local0.notice cgminer[375]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 30 06:21:03 (none) local0.notice cgminer[375]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:21:03 (none) local0.notice cgminer[375]: pic_heart_beat_func_new
Aug 30 06:21:03 (none) local0.notice cgminer[375]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:21:04 (none) local0.notice cgminer[375]: reset_all_hash_board
Aug 30 06:21:04 (none) local0.notice cgminer[375]: tty_init
Aug 30 06:21:04 (none) local0.notice cgminer[375]: tty_init_chain
Aug 30 06:21:04 (none) local0.notice cgminer[375]: tty_init_chain chainid = 0
Aug 30 06:21:04 (none) local0.err cgminer[375]: create rx read thread for chain 0 ok
Aug 30 06:21:04 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[0]
Aug 30 06:21:05 (none) local0.err cgminer[375]: create tx read thread for chain 0 ok
Aug 30 06:21:05 (none) local0.notice cgminer[375]: open device over
Aug 30 06:21:05 (none) local0.notice cgminer[375]: tty_init_chain
Aug 30 06:21:05 (none) local0.notice cgminer[375]: open device over
Aug 30 06:21:05 (none) local0.notice cgminer[375]: tty_init_chain
Aug 30 06:21:05 (none) local0.notice cgminer[375]: open device over
Aug 30 06:21:05 (none) local0.notice cgminer[375]: tty_init_chain
Aug 30 06:21:05 (none) local0.notice cgminer[375]: open device over
Aug 30 06:21:05 (none) local0.notice cgminer[375]: check_every_chain_asic_number
Aug 30 06:21:05 (none) local0.warn cgminer[375]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:21:06 (none) local0.notice cgminer[375]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:21:07 (none) local0.notice cgminer[375]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:21:08 (none) local0.notice cgminer[375]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:21:08 (none) local0.notice cgminer[375]: reset_all_hash_board
Aug 30 06:21:09 (none) local0.notice cgminer[375]: check_every_chain_asic_number
Aug 30 06:21:09 (none) local0.warn cgminer[375]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:21:10 (none) local0.notice cgminer[375]: recheck_asic_num DONE!
Aug 30 06:21:10 (none) local0.notice cgminer[375]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:21:11 (none) local0.notice cgminer[375]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:21:11 (none) local0.notice cgminer[375]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:21:12 (none) local0.notice cgminer[375]: reset_all_hash_board
Aug 30 06:21:13 (none) local0.notice cgminer[375]: check_every_chain_asic_number
Aug 30 06:21:13 (none) local0.warn cgminer[375]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:21:13 (none) local0.notice cgminer[375]: recheck_asic_num DONE!
Aug 30 06:21:13 (none) local0.notice cgminer[375]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:21:15 (none) local0.notice cgminer[375]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:21:15 (none) local0.notice cgminer[375]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:21:16 (none) local0.notice cgminer[375]: reset_all_hash_board
Aug 30 06:21:17 (none) local0.notice cgminer[375]: check_every_chain_asic_number
Aug 30 06:21:17 (none) local0.warn cgminer[375]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:21:17 (none) local0.notice cgminer[375]: recheck_asic_num DONE!
Aug 30 06:21:17 (none) local0.err cgminer[375]: calculate_address_interval: temp_asic_number = -1, set addrInterval = '7'
Aug 30 06:21:17 (none) local0.notice cgminer[375]: set_ticket_mask ticket_mask = 0x0000001b
Aug 30 06:21:17 (none) local0.notice cgminer[375]: set_frequency: frequency = 100
Aug 30 06:21:17 (none) local0.notice cgminer[375]: software_set_address_chain: chain 0 has 0 ASIC, and addrInterval is 7
Aug 30 06:21:17 (none) local0.notice cgminer[375]: Now Set [0] Chain Address
Aug 30 06:21:18 (none) local0.notice cgminer[375]: software_set_address_chain: chain 1 has 0 ASIC, and addrInterval is 7
Aug 30 06:21:18 (none) local0.notice cgminer[375]: software_set_address_chain: chain 2 has 0 ASIC, and addrInterval is 7
Aug 30 06:21:18 (none) local0.notice cgminer[375]: software_set_address_chain: chain 3 has 0 ASIC, and addrInterval is 7
Aug 30 06:21:18 (none) local0.notice cgminer[375]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:21:18 (none) local0.notice cgminer[375]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:21:18 (none) local0.notice cgminer[375]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:21:18 (none) local0.notice cgminer[375]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:21:18 (none) local0.notice cgminer[375]: select_core_to_check_temperature: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:21:18 (none) local0.notice cgminer[375]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:21:18 (none) local0.notice cgminer[375]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:21:18 (none) local0.notice cgminer[375]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:21:18 (none) local0.notice cgminer[375]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:21:18 (none) local0.notice cgminer[375]: 0 calibration_sensor_offset_chain
Aug 30 06:21:19 (none) local0.notice cgminer[375]: chain:0 local:0 remote:0
Aug 30 06:21:19 (none) local0.warn cgminer[375]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 30 06:21:19 (none) local0.notice cgminer[375]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 30 06:21:19 (none) local0.warn cgminer[375]: Chain 0 set_temperature_offset_value_chain
Aug 30 06:21:19 (none) local0.warn cgminer[375]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 30 06:21:20 (none) local0.notice cgminer[375]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 30 06:21:20 (none) local0.notice cgminer[375]: frequency = '100'
Aug 30 06:21:20 (none) local0.notice cgminer[375]: dev.timeout = 21474828 us
Aug 30 06:21:20 (none) local0.notice cgminer[375]: open_core_chain
Aug 30 06:21:20 (none) local0.notice cgminer[375]: open_core_chain
Aug 30 06:21:20 (none) local0.notice cgminer[375]: open_core_chain
Aug 30 06:21:20 (none) local0.notice cgminer[375]: open_core_chain
Aug 30 06:21:22 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:23 (none) local0.err cgminer[375]: cgminer time error total_secs = 1535610083.784465 last_total_secs = 1.000000
Aug 30 06:21:23 (none) local0.warn cgminer[375]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:21:23 (none) local0.warn cgminer[375]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:21:23 (none) local0.warn cgminer[375]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:21:25 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:28 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:31 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:33 (none) local0.warn cgminer[375]: Waiting for work to be available from pools.
Aug 30 06:21:33 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:36 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:39 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:42 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:44 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:47 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:50 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:52 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:55 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:21:58 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:01 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:03 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:06 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:09 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:11 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:14 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:17 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:20 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:22 (none) local0.err cgminer[375]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:22:23 (none) local0.err cgminer[375]: No servers were found that could be used to get work from.
Aug 30 06:22:23 (none) local0.err cgminer[375]: Please check the details from the list below of the servers you have input
Aug 30 06:22:23 (none) local0.err cgminer[375]: Most likely you have input the wrong URL, forgotten to add a port, or have not set up workers
Aug 30 06:22:23 (none) local0.warn cgminer[375]: Pool: 0  URL:   User:   Password: 
Aug 30 06:22:23 (none) local0.warn cgminer[375]: Pool: 1  URL:   User:   Password: 
Aug 30 06:22:23 (none) local0.warn cgminer[375]: Pool: 2  URL:   User:   Password: 
Aug 30 06:22:23 (none) local0.err cgminer[375]: No servers could be used! Exiting.
Aug 30 06:22:35 (none) local0.err cgminer: Miner compile time: Mon Nov 20 17:06:56 CST 2017 type: Antminer D3
Aug 30 06:22:35 (none) local0.warn cgminer: Started cgminer 4.9.0
Aug 30 06:22:35 (none) local0.warn cgminer[11751]: bitmain_DASH_init
Aug 30 06:22:36 (none) local0.err cgminer[11751]: FAN1 too slow ...
Aug 30 06:22:36 (none) local0.err cgminer[11751]: FAN2 too slow ...
Aug 30 06:22:36 (none) local0.err cgminer[11751]: FAN1 too slow ...
Aug 30 06:22:36 (none) local0.err cgminer[11751]: FAN2 too slow ...
Aug 30 06:22:37 (none) local0.warn cgminer[11751]: check_fan_speed OK
Aug 30 06:22:37 (none) local0.notice cgminer[11751]: detected at /sys/class/gpio/gpio51/value  chain 0
Aug 30 06:22:37 (none) local0.notice cgminer[11751]: detect total chain num 1
Aug 30 06:22:37 (none) local0.notice cgminer[11751]: i2c init ok
Aug 30 06:22:37 (none) local0.notice cgminer[11751]: check_whether_need_update_pic_program
Aug 30 06:22:38 (none) local0.notice cgminer[11751]: reset_PIC16F1704_pic_new ok
Aug 30 06:22:38 (none) local0.notice cgminer[11751]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 30 06:22:39 (none) local0.notice cgminer[11751]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 30 06:22:39 (none) local0.notice cgminer[11751]: every_chain_reset_PIC16F1704_pic_new
Aug 30 06:22:40 (none) local0.notice cgminer[11751]: reset_PIC16F1704_pic_new ok
Aug 30 06:22:40 (none) local0.notice cgminer[11751]: every_chain_jump_from_loader_to_app_PIC16F1704_new
Aug 30 06:22:41 (none) local0.notice cgminer[11751]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 30 06:22:42 (none) local0.notice cgminer[11751]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:22:42 (none) local0.notice cgminer[11751]: pic_heart_beat_func_new
Aug 30 06:22:42 (none) local0.notice cgminer[11751]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:22:42 (none) local0.notice cgminer[11751]: reset_all_hash_board
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: tty_init
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: tty_init_chain
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: tty_init_chain chainid = 0
Aug 30 06:22:43 (none) local0.err cgminer[11751]: create rx read thread for chain 0 ok
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: Start A New Asic Response.Chain Id:[0]
Aug 30 06:22:43 (none) local0.err cgminer[11751]: create tx read thread for chain 0 ok
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: open device over
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: tty_init_chain
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: open device over
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: tty_init_chain
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: open device over
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: tty_init_chain
Aug 30 06:22:43 (none) local0.notice cgminer[11751]: open device over
Aug 30 06:22:44 (none) local0.notice cgminer[11751]: check_every_chain_asic_number
Aug 30 06:22:44 (none) local0.warn cgminer[11751]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:22:45 (none) local0.notice cgminer[11751]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:22:46 (none) local0.notice cgminer[11751]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:22:46 (none) local0.notice cgminer[11751]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:22:47 (none) local0.notice cgminer[11751]: reset_all_hash_board
Aug 30 06:22:48 (none) local0.notice cgminer[11751]: check_every_chain_asic_number
Aug 30 06:22:48 (none) local0.warn cgminer[11751]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:22:48 (none) local0.notice cgminer[11751]: recheck_asic_num DONE!
Aug 30 06:22:48 (none) local0.notice cgminer[11751]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:22:50 (none) local0.notice cgminer[11751]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:22:50 (none) local0.notice cgminer[11751]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:22:51 (none) local0.notice cgminer[11751]: reset_all_hash_board
Aug 30 06:22:51 (none) local0.notice cgminer[11751]: check_every_chain_asic_number
Aug 30 06:22:52 (none) local0.warn cgminer[11751]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:22:52 (none) local0.notice cgminer[11751]: recheck_asic_num DONE!
Aug 30 06:22:52 (none) local0.notice cgminer[11751]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:22:54 (none) local0.notice cgminer[11751]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:22:54 (none) local0.notice cgminer[11751]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:22:54 (none) local0.notice cgminer[11751]: reset_all_hash_board
Aug 30 06:22:55 (none) local0.notice cgminer[11751]: check_every_chain_asic_number
Aug 30 06:22:55 (none) local0.warn cgminer[11751]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:22:56 (none) local0.notice cgminer[11751]: recheck_asic_num DONE!
Aug 30 06:22:56 (none) local0.err cgminer[11751]: calculate_address_interval: temp_asic_number = -1, set addrInterval = '7'
Aug 30 06:22:56 (none) local0.notice cgminer[11751]: set_ticket_mask ticket_mask = 0x0000001b
Aug 30 06:22:56 (none) local0.notice cgminer[11751]: set_frequency: frequency = 100
Aug 30 06:22:56 (none) local0.notice cgminer[11751]: software_set_address_chain: chain 0 has 0 ASIC, and addrInterval is 7
Aug 30 06:22:56 (none) local0.notice cgminer[11751]: Now Set [0] Chain Address
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: software_set_address_chain: chain 1 has 0 ASIC, and addrInterval is 7
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: software_set_address_chain: chain 2 has 0 ASIC, and addrInterval is 7
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: software_set_address_chain: chain 3 has 0 ASIC, and addrInterval is 7
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: select_core_to_check_temperature: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: 0 calibration_sensor_offset_chain
Aug 30 06:22:57 (none) local0.notice cgminer[11751]: chain:0 local:0 remote:0
Aug 30 06:22:57 (none) local0.warn cgminer[11751]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 30 06:22:58 (none) local0.notice cgminer[11751]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 30 06:22:58 (none) local0.warn cgminer[11751]: Chain 0 set_temperature_offset_value_chain
Aug 30 06:22:58 (none) local0.warn cgminer[11751]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 30 06:22:59 (none) local0.notice cgminer[11751]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 30 06:22:59 (none) local0.notice cgminer[11751]: frequency = '100'
Aug 30 06:22:59 (none) local0.notice cgminer[11751]: dev.timeout = 21474828 us
Aug 30 06:22:59 (none) local0.notice cgminer[11751]: open_core_chain
Aug 30 06:22:59 (none) local0.notice cgminer[11751]: open_core_chain
Aug 30 06:22:59 (none) local0.notice cgminer[11751]: open_core_chain
Aug 30 06:22:59 (none) local0.notice cgminer[11751]: open_core_chain
Aug 30 06:23:01 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:02 (none) local0.warn cgminer[11751]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:23:02 (none) local0.warn cgminer[11751]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:23:02 (none) local0.warn cgminer[11751]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:23:02 (none) local0.err cgminer[11751]: cgminer time error total_secs = 1535610182.473089 last_total_secs = 1.000000
Aug 30 06:23:04 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:07 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:09 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:12 (none) local0.warn cgminer[11751]: Waiting for work to be available from pools.
Aug 30 06:23:12 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:15 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:17 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:20 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:23 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:26 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:28 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:31 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:34 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:36 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:39 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:42 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:45 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:47 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:50 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:53 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:56 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:23:58 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:24:01 (none) local0.err cgminer[11751]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:24:02 (none) local0.err cgminer[11751]: No servers were found that could be used to get work from.
Aug 30 06:24:02 (none) local0.err cgminer[11751]: Please check the details from the list below of the servers you have input
Aug 30 06:24:02 (none) local0.err cgminer[11751]: Most likely you have input the wrong URL, forgotten to add a port, or have not set up workers
Aug 30 06:24:02 (none) local0.warn cgminer[11751]: Pool: 0  URL:   User:   Password: 
Aug 30 06:24:02 (none) local0.warn cgminer[11751]: Pool: 1  URL:   User:   Password: 
Aug 30 06:24:02 (none) local0.warn cgminer[11751]: Pool: 2  URL:   User:   Password: 
Aug 30 06:24:02 (none) local0.err cgminer[11751]: No servers could be used! Exiting.
Aug 30 06:24:16 (none) local0.err cgminer: Miner compile time: Mon Nov 20 17:06:56 CST 2017 type: Antminer D3
Aug 30 06:24:16 (none) local0.warn cgminer: Started cgminer 4.9.0
Aug 30 06:24:16 (none) local0.warn cgminer[23320]: bitmain_DASH_init
Aug 30 06:24:16 (none) local0.err cgminer[23320]: FAN1 too slow ...
Aug 30 06:24:16 (none) local0.err cgminer[23320]: FAN2 too slow ...
Aug 30 06:24:17 (none) local0.err cgminer[23320]: FAN1 too slow ...
Aug 30 06:24:17 (none) local0.err cgminer[23320]: FAN2 too slow ...
Aug 30 06:24:17 (none) local0.warn cgminer[23320]: check_fan_speed OK
Aug 30 06:24:17 (none) local0.notice cgminer[23320]: detected at /sys/class/gpio/gpio51/value  chain 0
Aug 30 06:24:17 (none) local0.notice cgminer[23320]: detect total chain num 1
Aug 30 06:24:17 (none) local0.notice cgminer[23320]: i2c init ok
Aug 30 06:24:17 (none) local0.notice cgminer[23320]: check_whether_need_update_pic_program
Aug 30 06:24:18 (none) local0.notice cgminer[23320]: reset_PIC16F1704_pic_new ok
Aug 30 06:24:19 (none) local0.notice cgminer[23320]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 30 06:24:19 (none) local0.notice cgminer[23320]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 30 06:24:19 (none) local0.notice cgminer[23320]: every_chain_reset_PIC16F1704_pic_new
Aug 30 06:24:20 (none) local0.notice cgminer[23320]: reset_PIC16F1704_pic_new ok
Aug 30 06:24:21 (none) local0.notice cgminer[23320]: every_chain_jump_from_loader_to_app_PIC16F1704_new
Aug 30 06:24:21 (none) local0.notice cgminer[23320]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 30 06:24:22 (none) local0.notice cgminer[23320]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:24:22 (none) local0.notice cgminer[23320]: pic_heart_beat_func_new
Aug 30 06:24:22 (none) local0.notice cgminer[23320]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:24:23 (none) local0.notice cgminer[23320]: reset_all_hash_board
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: tty_init
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: tty_init_chain
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: tty_init_chain chainid = 0
Aug 30 06:24:24 (none) local0.err cgminer[23320]: create rx read thread for chain 0 ok
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: Start A New Asic Response.Chain Id:[0]
Aug 30 06:24:24 (none) local0.err cgminer[23320]: create tx read thread for chain 0 ok
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: open device over
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: tty_init_chain
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: open device over
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: tty_init_chain
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: open device over
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: tty_init_chain
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: open device over
Aug 30 06:24:24 (none) local0.notice cgminer[23320]: check_every_chain_asic_number
Aug 30 06:24:24 (none) local0.warn cgminer[23320]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:24:25 (none) local0.notice cgminer[23320]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:24:27 (none) local0.notice cgminer[23320]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:24:27 (none) local0.notice cgminer[23320]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:24:27 (none) local0.notice cgminer[23320]: reset_all_hash_board
Aug 30 06:24:28 (none) local0.notice cgminer[23320]: check_every_chain_asic_number
Aug 30 06:24:28 (none) local0.warn cgminer[23320]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:24:29 (none) local0.notice cgminer[23320]: recheck_asic_num DONE!
Aug 30 06:24:29 (none) local0.notice cgminer[23320]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:24:30 (none) local0.notice cgminer[23320]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:24:31 (none) local0.notice cgminer[23320]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:24:31 (none) local0.notice cgminer[23320]: reset_all_hash_board
Aug 30 06:24:32 (none) local0.notice cgminer[23320]: check_every_chain_asic_number
Aug 30 06:24:32 (none) local0.warn cgminer[23320]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:24:33 (none) local0.notice cgminer[23320]: recheck_asic_num DONE!
Aug 30 06:24:33 (none) local0.notice cgminer[23320]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 30 06:24:34 (none) local0.notice cgminer[23320]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 30 06:24:34 (none) local0.notice cgminer[23320]: enable_PIC16F1704_dc_dc_new ok
Aug 30 06:24:35 (none) local0.notice cgminer[23320]: reset_all_hash_board
Aug 30 06:24:36 (none) local0.notice cgminer[23320]: check_every_chain_asic_number
Aug 30 06:24:36 (none) local0.warn cgminer[23320]: check_asic_reg: Chain0 has 0 ASICs
Aug 30 06:24:36 (none) local0.notice cgminer[23320]: recheck_asic_num DONE!
Aug 30 06:24:36 (none) local0.err cgminer[23320]: calculate_address_interval: temp_asic_number = -1, set addrInterval = '7'
Aug 30 06:24:36 (none) local0.notice cgminer[23320]: set_ticket_mask ticket_mask = 0x0000001b
Aug 30 06:24:36 (none) local0.notice cgminer[23320]: set_frequency: frequency = 100
Aug 30 06:24:36 (none) local0.notice cgminer[23320]: software_set_address_chain: chain 0 has 0 ASIC, and addrInterval is 7
Aug 30 06:24:36 (none) local0.notice cgminer[23320]: Now Set [0] Chain Address
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: software_set_address_chain: chain 1 has 0 ASIC, and addrInterval is 7
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: software_set_address_chain: chain 2 has 0 ASIC, and addrInterval is 7
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: software_set_address_chain: chain 3 has 0 ASIC, and addrInterval is 7
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: select_core_to_check_temperature: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 30 06:24:37 (none) local0.notice cgminer[23320]: 0 calibration_sensor_offset_chain
Aug 30 06:24:38 (none) local0.notice cgminer[23320]: chain:0 local:0 remote:0
Aug 30 06:24:38 (none) local0.warn cgminer[23320]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 30 06:24:39 (none) local0.notice cgminer[23320]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 30 06:24:39 (none) local0.warn cgminer[23320]: Chain 0 set_temperature_offset_value_chain
Aug 30 06:24:39 (none) local0.warn cgminer[23320]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 30 06:24:39 (none) local0.notice cgminer[23320]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 30 06:24:39 (none) local0.notice cgminer[23320]: frequency = '100'
Aug 30 06:24:39 (none) local0.notice cgminer[23320]: dev.timeout = 21474828 us
Aug 30 06:24:39 (none) local0.notice cgminer[23320]: open_core_chain
Aug 30 06:24:39 (none) local0.notice cgminer[23320]: open_core_chain
Aug 30 06:24:39 (none) local0.notice cgminer[23320]: open_core_chain
Aug 30 06:24:39 (none) local0.notice cgminer[23320]: open_core_chain
Aug 30 06:24:42 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:24:42 (none) local0.warn cgminer[23320]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:24:42 (none) local0.warn cgminer[23320]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:24:42 (none) local0.warn cgminer[23320]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 30 06:24:42 (none) local0.err cgminer[23320]: cgminer time error total_secs = 1535610282.994779 last_total_secs = 1.000000
Aug 30 06:24:44 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:24:47 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:24:50 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:24:52 (none) local0.warn cgminer[23320]: Waiting for work to be available from pools.
Aug 30 06:24:53 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:24:55 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:24:58 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:01 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:03 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:06 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:09 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:12 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:14 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:17 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:20 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:22 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:25 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:28 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:31 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:33 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:36 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:39 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:41 (none) local0.err cgminer[23320]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 30 06:25:42 (none) local0.err cgminer[23320]: No servers were found that could be used to get work from.
Aug 30 06:25:42 (none) local0.err cgminer[23320]: Please check the details from the list below of the servers you have input
Aug 30 06:25:42 (none) local0.err cgminer[23320]: Most likely you have input the wrong URL, forgotten to add a port, or have not set up workers
Aug 30 06:25:42 (none) local0.warn cgminer[23320]: Pool: 0  URL:   User:   Password: 
Aug 30 06:25:42 (none) local0.warn cgminer[23320]: Pool: 1  URL:   User:   Password: 
Aug 30 06:25:42 (none) local0.warn cgminer[23320]: Pool: 2  URL:   User:   Password: 
Aug 30 06:25:42 (none) local0.err cgminer[23320]: No servers could be used! Exiting.
Aug 30 06:25:56 (none) local0.err cgminer: Miner compile time: Mon Nov 20 17:06:56 CST 2017 type: Antminer D3
Aug 30 06:25:56 (none) local0.warn cgminer: Started cgminer 4.9.0
Aug 30 06:25:56 (none) local0.warn cgminer[2315]: bitmain_DASH_init
Aug 30 06:25:57 (none) local0.err cgminer[2315]: FAN1 too slow ...
Aug 30 06:25:57 (none) local0.err cgminer[2315]: FAN2 too slow ...
Aug 30 06:25:57 (none) local0.err cgminer[2315]: FAN1 too slow ...
Aug 30 06:25:57 (none) local0.err cgminer[2315]: FAN2 too slow ...
Aug 30 06:25:58 (none) local0.warn cgminer[2315]: check_fan_speed OK
Aug 30 06:25:58 (none) local0.notice cgminer[2315]: detected at /sys/class/gpio/gpio51/value  chain 0
Aug 30 06:25:58 (none) local0.notice cgminer[2315]: detect total chain num 1
Aug 30 06:25:58 (none) local0.notice cgminer[2315]: i2c init ok
Aug 30 06:25:58 (none) local0.notice cgminer[2315]: check_whether_need_update_pic_program
Aug 30 06:25:59 (none) local0.notice cgminer[2315]: reset_PIC16F1704_pic_new ok
Aug 30 06:25:59 (none) local0.notice cgminer[2315]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 30 06:26:00 (none) local0.notice cgminer[2315]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 30 06:26:00 (none) local0.notice cgminer[2315]: every_chain_reset_PIC16F1704_pic_new
Aug 30 06:26:01 (none) local0.notice cgminer[2315]: reset_PIC16F1704_pic_new ok
Aug 30 06:26:01 (none) local0.notice cgminer[2315]: every_chain_jump_from_loader_to_app_PIC16F1704_new
Aug 30 06:26:02 (none) local0.notice cgminer[2315]: jump_from_loader_to_app_PIC16F1704_new ok

Завтра-послезавтра возьму осциллограф.

 

выбрал частоту 100  и удалил все пулы.

Плата на этой частоте теперь довольно долго прогревается. Можно будет потыкать осциллографом.

 

Куда теперь копать? 

В СЦ нести смысла нет. Ремонт выходит дороже чем исправная хэш-плата. 

 

Изменено пользователем MasterSat
Ссылка на комментарий
Поделиться на другие сайты

нашел такой вот пост:

Цитата

Есть шесть нерабочих лезвий D3. На всех антмайнер определяет «0 ASICs». Диагностировал умершие чипы по методу, предложенном автором данной статьи в коментах выше. Итак: На всех шести (!) лезвиях если подать на последний ряд 0.9В ограничив ток 1.5А, то проваливается напряжение до 0.3-0.7В, на остальных рядах потребление остается около 0.9В 0.8-0,9А. Через некоторое время температура одного из чипов становится чуть выше остальных. После демонтирования этого греющегося чипа напряжение перестает проваливаться. Было принято решение раздеребанить одну плату на донорские чипы и запаять вместо демонтированных. Результат: На всех платах (уже 5шт) определяется 55 (?) чипов. И самое интересное: на всех плата один и тотже чип был нерабочим: по маркировке на плате №55. Физически это крайний верхний чип со стороны подачи воздуха. На двух платах пробовал на местах демонтированого чипа кидать перемычки на информационные каналы, определялось 54 чипа, но напряжение очень превышало 0,9В. Не могу пока решить как двигаться дальше.

у меня тоже U55

Напряжения между доменами 0,72-0,75  Если  частоту с 100 увеличить до 537 напряжения немного подрастают. Плата нагреваться начинает быстрей. Но  особо горячих чипов не нахожу.
Засада!

На каждый ряд подавал 0,9В. Потребление 0,72-0,79 ампер. Ничего не греется.

Еще раз залил прошивку blissz. Менял напругу: lowest - 7.3 вольт, default 8 вольт и highest 8.7 вольт. На исправной плате так же.

все равно 0 ASICs.

 

Изменено пользователем MasterSat
Ссылка на комментарий
Поделиться на другие сайты

Маленькая победа!!!

Reset проходит до 60 асика. С0 и B0 тоже меняются.А вот RI1- RI54 всегда в нуле! 

RI55 - RI60 1,8 вольта!

Выпаял U54 асик. Вместо него, чтоб избежать перекосов по питанию, поставил сопротивление 50 ом.

Теперь 36 ASICs

Как так? почему не 53?  

Изменено пользователем MasterSat
Ссылка на комментарий
Поделиться на другие сайты

02.09.2018 в 16:52, MasterSat сказал:

Выпаял U54 асик. Вместо него, чтоб избежать перекосов по питанию, поставил сопротивление 50 ом.

Теперь 36 ASICs

Как так? почему не 53?  

а потому что 37 асик тоже сдох!  сопротивление в одну сторону 30 Ом, в другую 20 Ом.

 

Я тут сам с собой разговариваю...

В общем разобрался. 

Блин, хоть сервис по ремонту теперь открывай... 

 

 

Ссылка на комментарий
Поделиться на другие сайты

) Я слежу за тобой.

Добавлю информации. 

http://agansk.ru/tech/2017/11/30/control-board-bitmain-antminer-d3-dump-29f2g08abaea/

Ссылка на комментарий
Поделиться на другие сайты

  • 1 месяц спустя...

Какая реальная прибыль сейчас выходит грязными? Втм говорит, что найс на 60% выгоднее, чем копать дэш напрямую. Что же он роет?

Изменено пользователем Kamsaltumn
Ссылка на комментарий
Поделиться на другие сайты

Найс берет в аренду майнеры и продает их услуги третьим лицам, а что они копают, одному Богу известно.

Ссылка на комментарий
Поделиться на другие сайты

Если есть вопросы по ремонту Д3 и других муравьёв, пишите в личку. Если видит 0 асик, то либо кз, либо порты битые, если ХХ асик, то смотрите  RI по очереди с конца, подавая 1,8 в.

Ссылка на комментарий
Поделиться на другие сайты

Для публикации сообщений создайте учётную запись или авторизуйтесь

Вы должны быть пользователем, чтобы оставить комментарий

Создать учетную запись

Зарегистрируйте новую учётную запись в нашем сообществе. Это очень просто!

Регистрация нового пользователя

Войти

Уже есть аккаунт? Войти в систему.

Войти
  • Последние посетители   0 пользователей онлайн

    • Ни одного зарегистрированного пользователя не просматривает данную страницу
  • Similar Topics

    • Antminer L3, L3+

      Доброй ночи! пожалуйста помогите кто знает с antminer l3+  работает 1.5 недели, все было хорошо.  В один момент вижу, что он выключен пришел его перезагрузил и началось   Вообщем выдает ошибку socket connect failed. connection refused то иногда включается и показывает на второй плате 21 чип место 71  много раз перезагружал, перекинул с другого асика блок питания он все равно так   не майнит уходит в ошибку   что делать подскажите пожалуйста, асику всего полторы недели скрины приложил

      в ASIC/FPGA майнеры

    • Ремонт: Bitmain Antminer s7, s9, l3+

      Официальный сайт | Antminer. Все модели. Вопросы, помощь, обсуждение.   В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы.   Статьи на bits.media:   Полезное:   (!) FAQ (часто задаваемые вопросы)   -Как найти в продаже разъемы питания, какая маркировка

      в ASIC/FPGA майнеры

    • блок питания Antminer T21

      Нужен ваш совет . Есть ли какой то способ подключить Bitcoin Miner T21 190T Power supply AC Input voltage  380~415 3610W к одной фазной сети 200 - 230 вольт !? Векторный преобразователь частоты 220 > 380В сможет !? Например - https://spc.com.ua/ru/products/nietz-splc-nz2200-15gs2-vector-frequency-inverter-15kw-ip20-1phase-220v-to-3phase-380v

      в Блоки питания, ИБП, силовая часть

    • Antminer S17, S17pro, S17+, S17e, T17, T17e, T17+

      Официальный сайт | Manual | Прошивка (официальный сайт) | Прошивка (bits.media)   В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда,  F.A.Q по майнингу. Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы. Сообщения, не относящиеся к теме обсуждения (оффтоп), удаляются без предупреждения.   Технические характеристики:   Статьи на Bits.me

      в ASIC/FPGA майнеры

    • Antminer S19,-pro, S19j,-pro, S19a, S19i, S19 Hyd, S19pro Hyd, S19pro+ Hyd, T19 Hyd

      Официальный сайт | Manual | Прошивка (официальный сайт) | Прошивка (bits.media)   В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда,  F.A.Q по майнингу. Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы. Сообщения, не относящиеся к теме обсуждения (оффтоп), удаляются без предупреждения.   Технические характеристики:   Статьи на Bits.me

      в ASIC/FPGA майнеры

×
×
  • Создать...