Ремонт: Bitmain Antminer s7, s9, l3+

[Splinter]

@felixsheva346 Это зависит от ревизии платы. На древних платах ревизии 1.х использовались внутренние LDO чипов и там были задействованы ноги 10, 13 и 14. На платах с внешними LDO ревизий 3.x-5.x эти ноги не задействованы.

[lcat99]

4 часа назад, svm55 сказал:

Странно... Но ведь к тестпойнту не один чип, а два. На вход и выход. Может второй? Но тогда показало бы на землю 33 ом. У вас полный ноль?

 

Да, ноль, причем и все чипы домена снял, все равно. Тоже подумал может следующий коротит. Вечером отпаяю нижние радиаторы и под микроскопом просмотрю, может там что.

[felixsheva346]

@Splinter Принято, спасибо. Не могу найти где лайкнуть.

 Версия платы 4.21. Значит проблема не в этих отсутствующих дорожках, буду копать дальше ( плата периодически работала, постоянно "сваливаясь" в 1 asic, а после замены 1го чипа стабильно 0 asic.).

[svm55]

18 часов назад, lcat99 сказал:

что у 58 чипа (средний в предпоследнем домене) короткое замыкание

Ну, если считать  с 1 до 63, это 59-й. Кроче, между средним и крайним в последнем домене тестпойнт RST показывает КЗ. Что на плюс, что на минус - неважно, там даже при отпаянных чипах есть резистор между + и - 0,5 Ом. Там всего ничего - площадка 1 - отверстие - переход на нижнюю сторону - резистор 33 ом - тестпойнт - где то внутри дорожка - отверстие - площадка 31 крайнего чипа. Не верится, что вот это"где-то внутри дорожка" замкнута на землю. Всё остальное открыто. Внимательно смотрим, можно и 33 ом отпаять, чтоб точнее определить, в какую сторону.Или эти 33 Ома съехали, оно как раз под нижним радиатором, не видно просто так.

[lcat99]

4 часа назад, svm55 сказал:

Ну, если считать  с 1 до 63, это 59-й. Кроче, между средним и крайним в последнем домене тестпойнт RST показывает КЗ. Что на плюс, что на минус - неважно, там даже при отпаянных чипах есть резистор между + и - 0,5 Ом. Там всего ничего - площадка 1 - отверстие - переход на нижнюю сторону - резистор 33 ом - тестпойнт - где то внутри дорожка - отверстие - площадка 31 крайнего чипа. Не верится, что вот это"где-то внутри дорожка" замкнута на землю. Всё остальное открыто. Внимательно смотрим, можно и 33 ом отпаять, чтоб точнее определить, в какую сторону.Или эти 33 Ома съехали, оно как раз под нижним радиатором, не видно просто так.

 

Нашел причину. Отпаял нижние радиаторы, внимательно изучил все дорожки 58 под микроскопом, и у следующего (59) чипа обнаружил что-то вроде серых окислов в районе тестпоинта, похожи внешне просто на пыль, но под микроскопом хорошо видно, что именно окислы. Там же был и старый флюс, видимо чип перепаивался. Смыл их, и КЗ пропало. Первый раз такое вижу. Получается, что КЗ было в сторону следующего чипа, но звонилось на этом.

 

[svm55]

18 часов назад, felixsheva346 сказал:

 Версия платы 4.21

А значит питание на чипы подастся без контрольки. Что очень удобно для начальной проверки. 

[Daut Dbar]

24.07.2021 в 22:03, Daut Dbar сказал:

Кто знает у кого можно приобрести платные видеоролик? Как находить температуру ? когда все теспоинты в норме? 

 

[lcat99]

1 час назад, Daut Dbar сказал:

 

 

А зачем платные уроки? Тут в теме все подробно и не раз рассказывалось, просто и понятно, и здесь есть очень хорошие мастера, которые помогут советом.

Достаточно почитать например посты Splinter, svm55, и почти все вопросы отпадут.

 

[Helber]

1 час назад, Daut Dbar сказал:

Кто знает у кого можно приобрести платные видеоролик? Как находить температуру ? когда все теспоинты в норме? 

https://forum.bits.media/index.php?/topic/185468-ищу-себе-занятиеработусборка-подбор-комплектующих-консультация-обслуживание-ферм/
 

https://forum.bits.media/index.php?/topic/85182-консультации-любого-уровня-по-майнингу-монетам-помощь-новичкам-фермы-на-воде-свосжо-сборка-эксклюзивов-администрирование/#comments

 

@lcat99  , ну мало ли, может ему читать лень, а спрашивать много)

[Splinter]

24.07.2021 в 23:03, Daut Dbar сказал:

63 чипа нет хештрета. Ни как не могу найти чип который не видет темп ... Все показатели в норме по всем прошёлся  нигде ничего не коротит. Но как найти тот чип? Одно идинственое на  clk прыгает показатель 0.81-1.8. На фотке где отмечено крас точка у них так . Сделал замыкания rst на своих доменах, как должно показывать показывает , все чипы на своём месте, проверил bo  тоже в норме. Не знаю куда дальше копать. Сменил датчик темп  тоже, ничего не поменялось. В начали в этой плате не было питание , менял ШИМ контроля, плата завилась

LDO последних 5-ти доменов смотрите. Ну и посмотрите осциллограммы что там с вашим клоком в указанных вами точках происходит.

[Daut Dbar]

24.07.2021 в 22:03, Daut Dbar сказал:

Можно ставить донарский чип от т9+ на С9?

 

[Splinter]

@Daut Dbar Можно. Но может не тянуть по частоте. На T9+ обычно чипы похуже качеством.

[Daut Dbar]

@Splinter 

24.07.2021 в 22:03, Daut Dbar сказал:

Вы были правы. На тех местах где я ставил чипы от т9+, в красной зоне находилесь. После замены, все на место встало.))). Можете подсказать? где можно купить не дорого осциллограф? 

 

[ANDiOne]

Подскажите, проблема в чипах ? И не понятно сколько штук ?

Лог232.txt

[Splinter]

10 часов назад, Daut Dbar сказал:

где можно купить не дорого осциллограф? 

На авито. 

Хотя понятие "недорогой" очень относительно. 

1 час назад, ANDiOne сказал:

Подскажите, проблема в чипах ? И не понятно сколько штук ?

Лог232.txt 39 \u041a\u0431 · 2 downloads

Вирус похоже. Прошиавать пробовали? 

[ANDiOne]

Не пробовал прошивать еще, решил тут уточнить.

 

[Mora1]

Добрый день подскажите пожалуйста название микросхемы на фото 

[Splinter]

@ANDiOne Прошивайте, там дело до чипов даже не доходит, bmminer даже не запускается.

Изменено 28 июл 2021, 11:33 пользователем Splinter

[ANDiOne]

33 минуты назад, Splinter сказал:

@ANDiOne Прошивайте, там дело до чипов даже не доходит, bmminer даже не запускается.

Спасибо, очень помогли.

 

[svm55]

Какие разъёмы на вентиляторах? Приехали XH 2,54 мм 4pin c алиэкспресс. Вполне по шагу, но конструкция другая, это надо оба менять. А родные как называются?

[Splinter]

3 часа назад, svm55 сказал:

Какие разъёмы на вентиляторах? Приехали XH 2,54 мм 4pin c алиэкспресс. Вполне по шагу, но конструкция другая, это надо оба менять. А родные как называются?

Я както горсть в чипдипе брал, пришел и на витрине ткнул пальцем, так что точной тип незнаю, возможно вот этот коннектор 4 пин.

А если в Москве, то не заморачивайтесь и на авито возьмите - там никаких типов просто Разьемы вентилятора 4 пин

[svm55]

@Splinter Спасибо, разобрался. Называются они KF2510 - 4P, 2,54 мм. Их везде полно по рублю пучок.

[Daut Dbar]

] Добрый день@Splinter 

24.07.2021 в 22:03, Daut Dbar сказал:

Добрый день. Вопрос?  Кто-нибудь чинил С9к маленькие хеш платы ? И как искать неисправный чип? Вот лог 

Скрытый текст

 

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203784K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25592K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12552K (ccebe000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Broadcom BCM5241 e000b000.etherne:00: attached PHY driver [Broadcom BCM5241] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 113/50, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 11404/9457, WL threshold: 4096, image sequence number: 914180297
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BCBDE5E0-4C0B-4978-9734-FC58D9F68227, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
 [2021-07-29 07:31:25.828] httpListenThread start ret=0
 [2021-07-29 07:31:55.832] start listen on 6060 ...
 [2021-07-29 07:36:32.406] setStartTimePoint total_tv_start_sys=346 total_tv_end_sys=347

2021-07-29 07:31:25 cgminer.c:11470:cnt_of_proc: pidof cgminer command result is:1136

2021-07-29 07:31:25 cgminer.c:11471:cnt_of_proc: strlen is: 5
2021-07-29 07:31:25 cgminer.c:11492:cnt_of_proc: Parsed proc id is: 1136
2021-07-29 07:31:25 cgminer.c:11504:cnt_of_proc:  1 instance of cgminer is  already Running on this machine
2021-07-29 07:31:25 driver-btm-soc.c:6311:bitmain_soc_init: This is Antminer S9k scan user version
2021-07-29 07:31:25 driver-btm-soc.c:6317:bitmain_soc_init: special mode: disabled
2021-07-29 07:31:25 driver-btm-soc.c:6324:bitmain_soc_init: This is high performance mode
2021-07-29 07:31:25 driver-btm-soc.c:6329:bitmain_soc_init: last commit version: 94e8f08 commit time: 2019-10-31 10:33:22 build: 2019-12-13 10:14:11
2021-07-29 07:31:25 driver-btm-soc.c:6350:bitmain_soc_init: Detect 256MB control board of XILINX
2021-07-29 07:31:25 driver-btm-soc.c:6353:bitmain_soc_init: Miner compile time: Fri Dec 13 10:01:09 CST 2019 type: Antminer S9k
2021-07-29 07:31:25 driver-btm-soc.c:849:check_chain: get_hash_on_plug is 0x7
2021-07-29 07:31:25 driver-btm-soc.c:861:check_chain: !! chain[0]is exist
2021-07-29 07:31:25 driver-btm-soc.c:861:check_chain: !! chain[1]is exist
2021-07-29 07:31:25 driver-btm-soc.c:861:check_chain: !! chain[2]is exist
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fb 28 fe ff
00000080 ff ff ff ff ff ff ff c3   4d 4d 4d 4d 4d 4d 4d 4d
00000090 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000a0 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000b0 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000c0 4d 4d 4d 4d 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff a7 12 00 00   90 ff ff ff 39 10 f0 a4
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fb 28 fe ff
00000080 ff ff ff ff ff ff ff c3   4d 4d 4d 4d 4d 4d 4d 4d
00000090 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000a0 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000b0 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000c0 4d 4d 4d 4d 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff a7 12 00 00   90 ff ff ff 39 10 f0 a4
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fb 28 fe ff
00000080 ff ff ff ff ff ff ff c3   4d 4d 4d 4d 4d 4d 4d 4d
00000090 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000a0 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000b0 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000c0 4d 4d 4d 4d 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff a7 12 00 00   90 ff ff ff 39 10 f0 a4

read chain[0] hardware info:
major type: 0
minor type: 2
chip level: 2
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

read chain[1] hardware info:
major type: 0
minor type: 2
chip level: 2
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

read chain[2] hardware info:
major type: 0
minor type: 2
chip level: 2
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

sweep config for eco mode: 
sweep_start_voltage: 9.44
max_aging_voltage:   9.84
sweep_min_freq:      270M
sweep_max_freq:      310M

sweep config for hpf mode: 
sweep_start_voltage: 9.90
max_aging_voltage:   10.30
sweep_min_freq:      355M
sweep_max_freq:      385M
2021-07-29 07:31:38 driver-btm-soc.c:5770:get_freq_result_from_eeprom: orginal chip freq: 
chain 0 freq:
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 

chain 1 freq:
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 

chain 2 freq:
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 

2021-07-29 07:31:38 driver-btm-soc.c:6443:bitmain_soc_init: reset all...
2021-07-29 07:31:40 driver-btm-soc.c:6451:bitmain_soc_init: miner ID : 8028d42a7910481c
2021-07-29 07:31:40 driver-btm-soc.c:6112:init_miner_version: FPGA Version = 0xB00D
2021-07-29 07:32:00 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[0] PIC software version: 176
2021-07-29 07:32:00 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[1] PIC software version: 177
2021-07-29 07:32:01 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[2] PIC software version: 176
2021-07-29 07:32:01 power.c:185:power_init: power init ... 
2021-07-29 07:32:01 driver-btm-soc.c:4877:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[0] eeprom
2021-07-29 07:32:01 power.c:232:set_working_voltage_by_chain: chain[0] working_voltage = 9.90
2021-07-29 07:32:01 driver-btm-soc.c:4877:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[1] eeprom
2021-07-29 07:32:01 power.c:232:set_working_voltage_by_chain: chain[1] working_voltage = 9.90
2021-07-29 07:32:01 driver-btm-soc.c:4877:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[2] eeprom
2021-07-29 07:32:01 power.c:232:set_working_voltage_by_chain: chain[2] working_voltage = 9.90
2021-07-29 07:32:01 driver-btm-soc.c:5560:update_highest_voltage: chain 0 hpf working voltage 9.90
2021-07-29 07:32:01 driver-btm-soc.c:5560:update_highest_voltage: chain 1 hpf working voltage 9.90
2021-07-29 07:32:01 driver-btm-soc.c:5560:update_highest_voltage: chain 2 hpf working voltage 9.90
2021-07-29 07:32:01 driver-btm-soc.c:5569:update_highest_voltage: open core at max voltage 10.20
2021-07-29 07:32:01 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[0] setting to highest voltage: 10.20 ...
2021-07-29 07:32:03 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 
2021-07-29 07:32:04 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[1] setting to highest voltage: 10.20 ...
2021-07-29 07:32:04 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 
2021-07-29 07:32:04 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[2] setting to highest voltage: 10.20 ...
2021-07-29 07:32:05 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 
2021-07-29 07:32:06 driver-btm-soc.c:1259:get_ideal_hash_rate: get ideal hash rate 14000
2021-07-29 07:32:06 eeprom.c:675:travel_eeprom_store: chain[0] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:385 IC[001]:385 IC[002]:385 IC[003]:385 IC[004]:385 IC[005]:385 IC[006]:385 IC[007]:385 IC[008]:385 IC[009]:385 
IC[010]:385 IC[011]:385 IC[012]:385 IC[013]:385 IC[014]:385 IC[015]:385 IC[016]:385 IC[017]:385 IC[018]:385 IC[019]:385 
IC[020]:385 IC[021]:385 IC[022]:385 IC[023]:385 IC[024]:385 IC[025]:385 IC[026]:385 IC[027]:385 IC[028]:385 IC[029]:385 
IC[030]:385 IC[031]:385 IC[032]:385 IC[033]:385 IC[034]:385 IC[035]:385 IC[036]:385 IC[037]:385 IC[038]:385 IC[039]:385 
IC[040]:385 IC[041]:385 IC[042]:385 IC[043]:385 IC[044]:385 IC[045]:385 IC[046]:385 IC[047]:385 IC[048]:385 IC[049]:385 
IC[050]:385 IC[051]:385 IC[052]:385 IC[053]:385 IC[054]:385 IC[055]:385 IC[056]:385 IC[057]:385 IC[058]:385 IC[059]:385 
voltage in mode2: 9.90 V
hash rate in mode2: 04775 GH/s

2021-07-29 07:32:06 eeprom.c:675:travel_eeprom_store: chain[1] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:385 IC[001]:385 IC[002]:385 IC[003]:385 IC[004]:385 IC[005]:385 IC[006]:385 IC[007]:385 IC[008]:385 IC[009]:385 
IC[010]:385 IC[011]:385 IC[012]:385 IC[013]:385 IC[014]:385 IC[015]:385 IC[016]:385 IC[017]:385 IC[018]:385 IC[019]:385 
IC[020]:385 IC[021]:385 IC[022]:385 IC[023]:385 IC[024]:385 IC[025]:385 IC[026]:385 IC[027]:385 IC[028]:385 IC[029]:385 
IC[030]:385 IC[031]:385 IC[032]:385 IC[033]:385 IC[034]:385 IC[035]:385 IC[036]:385 IC[037]:385 IC[038]:385 IC[039]:385 
IC[040]:385 IC[041]:385 IC[042]:385 IC[043]:385 IC[044]:385 IC[045]:385 IC[046]:385 IC[047]:385 IC[048]:385 IC[049]:385 
IC[050]:385 IC[051]:385 IC[052]:385 IC[053]:385 IC[054]:385 IC[055]:385 IC[056]:385 IC[057]:385 IC[058]:385 IC[059]:385 
voltage in mode2: 9.90 V
hash rate in mode2: 04775 GH/s

2021-07-29 07:32:06 eeprom.c:675:travel_eeprom_store: chain[2] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:385 IC[001]:385 IC[002]:385 IC[003]:385 IC[004]:385 IC[005]:385 IC[006]:385 IC[007]:385 IC[008]:385 IC[009]:385 
IC[010]:385 IC[011]:385 IC[012]:385 IC[013]:385 IC[014]:385 IC[015]:385 IC[016]:385 IC[017]:385 IC[018]:385 IC[019]:385 
IC[020]:385 IC[021]:385 IC[022]:385 IC[023]:385 IC[024]:385 IC[025]:385 IC[026]:385 IC[027]:385 IC[028]:385 IC[029]:385 
IC[030]:385 IC[031]:385 IC[032]:385 IC[033]:385 IC[034]:385 IC[035]:385 IC[036]:385 IC[037]:385 IC[038]:385 IC[039]:385 
IC[040]:385 IC[041]:385 IC[042]:385 IC[043]:385 IC[044]:385 IC[045]:385 IC[046]:385 IC[047]:385 IC[048]:385 IC[049]:385 
IC[050]:385 IC[051]:385 IC[052]:385 IC[053]:385 IC[054]:385 IC[055]:385 IC[056]:385 IC[057]:385 IC[058]:385 IC[059]:385 
voltage in mode2: 9.90 V
hash rate in mode2: 04775 GH/s

2021-07-29 07:32:06 driver-btm-soc.c:6494:bitmain_soc_init: fan_eft : 0  fan_pwm : 0
2021-07-29 07:32:07 driver-btm-soc.c:6141:bring_up_chain: 

bring up chain 0
2021-07-29 07:32:07 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-07-29 07:32:40 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-07-29 07:32:41 driver-btm-soc.c:3807:check_asic_num: without pre_open_core chain 0, find asic num = 60
2021-07-29 07:32:45 driver-btm-soc.c:4630:set_freq_by_chain: chain[0] set freq:100.00
2021-07-29 07:32:45 driver-btm-soc.c:3853:open_core_BM1393_pre_open: pre open core = 13
2021-07-29 07:32:45 driver-btm-soc.c:3733:pre_open_core_one_chain: for chain 0
2021-07-29 07:32:45 temperature.c:591:is_eeprom_tempsensor_data_correct: check sensor info ...
2021-07-29 07:32:45 temperature.c:606:is_eeprom_tempsensor_data_correct: sensor type is TMP451
2021-07-29 07:32:45 temperature.c:618:is_eeprom_tempsensor_data_correct: 2
2021-07-29 07:32:45 temperature.c:632:is_eeprom_tempsensor_data_correct: sensor num is 2
2021-07-29 07:32:45 temperature.c:641:is_eeprom_tempsensor_data_correct: sensor pos = 31, 40, 0, 0
2021-07-29 07:32:46 temperature.c:659:is_eeprom_tempsensor_data_correct: chain[0] temp sensor info, correct!
2021-07-29 07:32:46 temperature.c:748:check_eeprom_calibration_data: chain[0] no need to calibrate !
2021-07-29 07:32:46 temperature.c:524:is_tempsensor_data_correct: Bad,temp_info.type = 0
2021-07-29 07:32:46 temperature.c:763:calibration_sensor_offset: chain[0] temp info,Bad. Reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0 
sensor offset: -5  -2  0  0  0  0 
2021-07-29 07:32:46 temperature.c:801:calibration_sensor_offset: get temp info from eeprom,just use it!
2021-07-29 07:32:46 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x7a61, cmd_buf[2]=0x1a000000, misc=0x7a61
2021-07-29 07:32:46 temperature.c:818:calibration_sensor_offset: Chain[0] chip[31] use PIC middle temp offset=-5, typeID=55
2021-07-29 07:32:46 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[0] Chip[31] local:0 remote:0 offset:-5 
2021-07-29 07:32:46 temperature.c:870:calibration_sensor_offset: Chain[0] Chip[31] get middle temp offset=-5 typeID=55
2021-07-29 07:32:46 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x7a61, cmd_buf[2]=0x13000000, misc=0x7a61
2021-07-29 07:32:46 temperature.c:818:calibration_sensor_offset: Chain[0] chip[40] use PIC middle temp offset=-2, typeID=55
2021-07-29 07:32:47 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[0] Chip[40] local:0 remote:0 offset:-2 
2021-07-29 07:32:47 temperature.c:870:calibration_sensor_offset: Chain[0] Chip[40] get middle temp offset=-2 typeID=55
2021-07-29 07:32:47 driver-btm-soc.c:6141:bring_up_chain: 

bring up chain 1
2021-07-29 07:32:47 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-07-29 07:33:19 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-07-29 07:33:20 driver-btm-soc.c:3807:check_asic_num: without pre_open_core chain 1, find asic num = 60
2021-07-29 07:33:24 driver-btm-soc.c:4630:set_freq_by_chain: chain[1] set freq:100.00
2021-07-29 07:33:24 driver-btm-soc.c:3853:open_core_BM1393_pre_open: pre open core = 13
2021-07-29 07:33:24 driver-btm-soc.c:3733:pre_open_core_one_chain: for chain 1
2021-07-29 07:33:24 temperature.c:591:is_eeprom_tempsensor_data_correct: check sensor info ...
2021-07-29 07:33:24 temperature.c:606:is_eeprom_tempsensor_data_correct: sensor type is TMP451
2021-07-29 07:33:25 temperature.c:618:is_eeprom_tempsensor_data_correct: 2
2021-07-29 07:33:25 temperature.c:632:is_eeprom_tempsensor_data_correct: sensor num is 2
2021-07-29 07:33:25 temperature.c:641:is_eeprom_tempsensor_data_correct: sensor pos = 31, 40, 0, 0
2021-07-29 07:33:25 temperature.c:659:is_eeprom_tempsensor_data_correct: chain[1] temp sensor info, correct!
2021-07-29 07:33:25 temperature.c:748:check_eeprom_calibration_data: chain[1] no need to calibrate !
2021-07-29 07:33:25 temperature.c:524:is_tempsensor_data_correct: Bad,temp_info.type = 0
2021-07-29 07:33:25 temperature.c:763:calibration_sensor_offset: chain[1] temp info,Bad. Reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0 
sensor offset: -5  -2  0  0  0  0 
2021-07-29 07:33:25 temperature.c:801:calibration_sensor_offset: get temp info from eeprom,just use it!
2021-07-29 07:33:25 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x7a61, cmd_buf[2]=0x1a000000, misc=0x7a61
2021-07-29 07:33:25 temperature.c:818:calibration_sensor_offset: Chain[1] chip[31] use PIC middle temp offset=-5, typeID=55
2021-07-29 07:33:25 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[1] Chip[31] local:0 remote:0 offset:-5 
2021-07-29 07:33:25 temperature.c:870:calibration_sensor_offset: Chain[1] Chip[31] get middle temp offset=-5 typeID=55
2021-07-29 07:33:25 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x7a61, cmd_buf[2]=0x13000000, misc=0x7a61
2021-07-29 07:33:25 temperature.c:818:calibration_sensor_offset: Chain[1] chip[40] use PIC middle temp offset=-2, typeID=55
2021-07-29 07:33:26 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[1] Chip[40] local:0 remote:0 offset:-2 
2021-07-29 07:33:26 temperature.c:870:calibration_sensor_offset: Chain[1] Chip[40] get middle temp offset=-2 typeID=55
2021-07-29 07:33:26 driver-btm-soc.c:6141:bring_up_chain: 

bring up chain 2
2021-07-29 07:33:26 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffc
2021-07-29 07:33:58 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2021-07-29 07:33:59 driver-btm-soc.c:3807:check_asic_num: without pre_open_core chain 2, find asic num = 60
2021-07-29 07:34:03 driver-btm-soc.c:4630:set_freq_by_chain: chain[2] set freq:100.00
2021-07-29 07:34:03 driver-btm-soc.c:3853:open_core_BM1393_pre_open: pre open core = 13
2021-07-29 07:34:04 driver-btm-soc.c:3733:pre_open_core_one_chain: for chain 2
2021-07-29 07:34:04 temperature.c:591:is_eeprom_tempsensor_data_correct: check sensor info ...
2021-07-29 07:34:04 temperature.c:606:is_eeprom_tempsensor_data_correct: sensor type is TMP451
2021-07-29 07:34:04 temperature.c:618:is_eeprom_tempsensor_data_correct: 2
2021-07-29 07:34:04 temperature.c:632:is_eeprom_tempsensor_data_correct: sensor num is 2
2021-07-29 07:34:04 temperature.c:641:is_eeprom_tempsensor_data_correct: sensor pos = 31, 40, 0, 0
2021-07-29 07:34:04 temperature.c:659:is_eeprom_tempsensor_data_correct: chain[2] temp sensor info, correct!
2021-07-29 07:34:04 temperature.c:748:check_eeprom_calibration_data: chain[2] no need to calibrate !
2021-07-29 07:34:04 temperature.c:524:is_tempsensor_data_correct: Bad,temp_info.type = 0
2021-07-29 07:34:04 temperature.c:763:calibration_sensor_offset: chain[2] temp info,Bad. Reload from eeprom..
sensor type = 1,sensor num = 2
sensor pos: 31  40  0  0  0  0 
sensor offset: -5  -2  0  0  0  0 
2021-07-29 07:34:04 temperature.c:801:calibration_sensor_offset: get temp info from eeprom,just use it!
2021-07-29 07:34:04 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x7a61, cmd_buf[2]=0x1a000000, misc=0x7a61
2021-07-29 07:34:04 temperature.c:818:calibration_sensor_offset: Chain[2] chip[31] use PIC middle temp offset=-5, typeID=55
2021-07-29 07:34:04 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[2] Chip[31] local:0 remote:0 offset:-5 
2021-07-29 07:34:04 temperature.c:870:calibration_sensor_offset: Chain[2] Chip[31] get middle temp offset=-5 typeID=55
2021-07-29 07:34:04 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x7a61, cmd_buf[2]=0x13000000, misc=0x7a61
2021-07-29 07:34:05 temperature.c:818:calibration_sensor_offset: Chain[2] chip[40] use PIC middle temp offset=-2, typeID=55
2021-07-29 07:34:05 temperature.c:346:do_calibration_sensor_offset_by_eeprom: New offset - Chain[2] Chip[40] local:0 remote:0 offset:-2 
2021-07-29 07:34:05 temperature.c:870:calibration_sensor_offset: Chain[2] Chip[40] get middle temp offset=-2 typeID=55
2021-07-29 07:34:05 asic.c:1153:set_baud: set baud=1
2021-07-29 07:34:05 asic.c:1126:set_baud_one_chain: cmd_buf[0]=0x51090018, cmd_buf[1]=0x2101, cmd_buf[2]=0x11000000, misc=0x2101
2021-07-29 07:34:05 asic.c:1126:set_baud_one_chain: cmd_buf[0]=0x51090018, cmd_buf[1]=0x2101, cmd_buf[2]=0x11000000, misc=0x2101
2021-07-29 07:34:05 asic.c:1126:set_baud_one_chain: cmd_buf[0]=0x51090018, cmd_buf[1]=0x2101, cmd_buf[2]=0x11000000, misc=0x2101
2021-07-29 07:34:05 asic.c:1164:set_baud: read bc write is 0x82001a
2021-07-29 07:34:05 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x6161, cmd_buf[2]=0x13000000, misc=0x6161
2021-07-29 07:34:05 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x6161, cmd_buf[2]=0x1a000000, misc=0x6161
2021-07-29 07:34:05 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x6161, cmd_buf[2]=0x13000000, misc=0x6161
2021-07-29 07:34:05 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x6161, cmd_buf[2]=0x1a000000, misc=0x6161
2021-07-29 07:34:05 asic.c:1429:set_misc_control: cmd_buf[0]=0x41097818, cmd_buf[1]=0x6161, cmd_buf[2]=0x13000000, misc=0x6161
2021-07-29 07:34:05 asic.c:1429:set_misc_control: cmd_buf[0]=0x41099c18, cmd_buf[1]=0x6161, cmd_buf[2]=0x1a000000, misc=0x6161
2021-07-29 07:34:05 driver-btm-soc.c:6509:bitmain_soc_init: set TICKET_MASK
2021-07-29 07:34:06 temperature.c:2081:detect_startup_environment_temperature: Environment temperature: [30]
2021-07-29 07:34:06 temperature.c:2098:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 1 times ...
2021-07-29 07:34:17 temperature.c:2081:detect_startup_environment_temperature: Environment temperature: [30]
2021-07-29 07:34:17 temperature.c:2098:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 2 times ...
2021-07-29 07:34:28 temperature.c:2081:detect_startup_environment_temperature: Environment temperature: [30]
2021-07-29 07:34:28 temperature.c:2098:detect_startup_environment_temperature: Enter 10 secs to cool down hash board, 3 times ...
2021-07-29 07:34:38 driver-btm-soc.c:3884:set_clock_delay_control: set mode 0
2021-07-29 07:34:38 driver-btm-soc.c:3903:set_clock_delay_control: core_data = 0x04
2021-07-29 07:34:38 driver-btm-soc.c:3974:open_core_bm1393: Start Open Core!!
2021-07-29 07:34:44 driver-btm-soc.c:4041:open_core_bm1393: End Open Core!!
2021-07-29 07:34:46 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 125
2021-07-29 07:34:48 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 150
2021-07-29 07:34:50 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 175
2021-07-29 07:34:52 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 200
2021-07-29 07:34:54 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 225
2021-07-29 07:34:56 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 250
2021-07-29 07:34:58 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 275
2021-07-29 07:35:01 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 300
2021-07-29 07:35:03 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 325
2021-07-29 07:35:05 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 350
2021-07-29 07:35:07 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 375
2021-07-29 07:35:09 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[0] increase to 385
2021-07-29 07:35:11 driver-btm-soc.c:5209:increase_freq_by_eeprom_slowly: max = 385 ,min = 385
2021-07-29 07:35:11 driver-btm-soc.c:5215:increase_freq_by_eeprom_slowly: chain[0] increaseing the diff freq ...
2021-07-29 07:35:11 driver-btm-soc.c:5243:increase_freq_by_eeprom_slowly: chain 0 final freq setting:
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
2021-07-29 07:35:11 driver-btm-soc.c:5255:increase_freq_by_eeprom_slowly: set chain 0 to working voltage
2021-07-29 07:35:11 power.c:1309:slowly_set_working_power_t11: set chain 0 to working voltage:
now setting chain[0]-volt[10.09]-data[013] 
now setting chain[0]-volt[09.99]-data[015] 
now setting chain[0]-volt[09.94]-data[016] 
2021-07-29 07:35:19 power.c:1331:slowly_set_working_power_t11: done!
2021-07-29 07:35:19 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 125
2021-07-29 07:35:21 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 150
2021-07-29 07:35:23 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 175
2021-07-29 07:35:25 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 200
2021-07-29 07:35:27 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 225
2021-07-29 07:35:30 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 250
2021-07-29 07:35:32 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 275
2021-07-29 07:35:34 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 300
2021-07-29 07:35:36 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 325
2021-07-29 07:35:38 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 350
2021-07-29 07:35:40 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 375
2021-07-29 07:35:42 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[1] increase to 385
2021-07-29 07:35:45 driver-btm-soc.c:5209:increase_freq_by_eeprom_slowly: max = 385 ,min = 385
2021-07-29 07:35:45 driver-btm-soc.c:5215:increase_freq_by_eeprom_slowly: chain[1] increaseing the diff freq ...
2021-07-29 07:35:45 driver-btm-soc.c:5243:increase_freq_by_eeprom_slowly: chain 1 final freq setting:
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
2021-07-29 07:35:45 driver-btm-soc.c:5255:increase_freq_by_eeprom_slowly: set chain 1 to working voltage
2021-07-29 07:35:45 power.c:1309:slowly_set_working_power_t11: set chain 1 to working voltage:
now setting chain[1]-volt[10.09]-data[013] 
now setting chain[1]-volt[09.99]-data[015] 
now setting chain[1]-volt[09.94]-data[016] 
2021-07-29 07:35:55 power.c:1331:slowly_set_working_power_t11: done!
2021-07-29 07:35:55 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 125
2021-07-29 07:35:57 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 150
2021-07-29 07:35:59 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 175
2021-07-29 07:36:02 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 200
2021-07-29 07:36:04 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 225
2021-07-29 07:36:06 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 250
2021-07-29 07:36:08 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 275
2021-07-29 07:36:10 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 300
2021-07-29 07:36:12 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 325
2021-07-29 07:36:15 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 350
2021-07-29 07:36:17 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 375
2021-07-29 07:36:19 driver-btm-soc.c:5193:increase_freq_by_eeprom_slowly: chain[2] increase to 385
2021-07-29 07:36:21 driver-btm-soc.c:5209:increase_freq_by_eeprom_slowly: max = 385 ,min = 385
2021-07-29 07:36:21 driver-btm-soc.c:5215:increase_freq_by_eeprom_slowly: chain[2] increaseing the diff freq ...
2021-07-29 07:36:21 driver-btm-soc.c:5243:increase_freq_by_eeprom_slowly: chain 2 final freq setting:
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
2021-07-29 07:36:21 driver-btm-soc.c:5255:increase_freq_by_eeprom_slowly: set chain 2 to working voltage
2021-07-29 07:36:21 power.c:1309:slowly_set_working_power_t11: set chain 2 to working voltage:
now setting chain[2]-volt[10.09]-data[013] 
now setting chain[2]-volt[09.99]-data[015] 
now setting chain[2]-volt[09.94]-data[016] 
2021-07-29 07:36:29 power.c:1331:slowly_set_working_power_t11: done!
2021-07-29 07:36:29 driver-btm-soc.c:6545:bitmain_soc_init: set to working voltage...
2021-07-29 07:36:29 power.c:1258:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage:
now setting chain[0]-volt[09.94]-data[016] chain[1]-volt[09.94]-data[016] chain[2]-volt[09.94]-data[016] 
2021-07-29 07:36:31 power.c:1278:slowly_set_iic_power_voltage_t11: parallel set all chain to working voltage end!
now setting chain[0]-volt[09.90]-data[016] chain[1]-volt[09.90]-data[016] chain[2]-volt[09.90]-data[016] 
2021-07-29 07:36:31 driver-btm-soc.c:4929:set_timeout: freq 385 final timeout=340
2021-07-29 07:36:31 driver-btm-soc.c:2925:low_temp_process_parm_init: chip miner_type = [2]
2021-07-29 07:36:31 driver-btm-soc.c:2925:low_temp_process_parm_init: chip miner_type = [2]
2021-07-29 07:36:31 driver-btm-soc.c:2925:low_temp_process_parm_init: chip miner_type = [2]
2021-07-29 07:36:31 driver-btm-soc.c:3539:check_system_work: check system thread start...
2021-07-29 07:36:32 driver-btm-soc.c:6614:bitmain_soc_init: Init done!
2021-07-29 07:36:32 driver-btm-soc.c:7257:bitmain_soc_prepare: bitmain soc init success.
2021-07-29 07:36:32 util.c:2178:process_version_mask: Pool 1 Version num is 2
2021-07-29 07:36:32 util.c:2178:process_version_mask: Pool 1 Version num is 2
2021-07-29 07:36:32 util.c:2178:process_version_mask: Pool 0 Version num is 2
2021-07-29 07:36:32 util.c:2178:process_version_mask: Pool 0 Version num is 2
2021-07-29 07:36:33 temperature.c:1542:read_temp_func: bring_up_pcb_temp = 36
2021-07-29 07:36:33 driver-btm-soc.c:6932:send_job: Version num 2

 

 

 

 

 

 

Изменено 29 июл 2021, 08:39 пользователем Daut Dbar

[VadimZ]

Подскажите, какие факторы (температура, напряжение питания, частота и др. сочетания факторов) влияют на долгосрочность работы хеш плат S9 ? Дохнут как мухи осенью. Не могу понять в чем причина. 

Изменено 29 июл 2021, 15:45 пользователем VadimZ

[vovchik]

@Daut Dbar 

Прячем под спойлер эту простыню.