Ремонт: Bitmain Antminer s7, s9, l3+

profipc · 7 апр 2018, 18:55

@yaroslav1980@mail.ru шлейф проверьте. Либо подкиньте с соседнего лезвия.

yaroslav1980@mail.ru · 7 апр 2018, 18:56

Только что, profipc сказал:

@yaroslav1980@mail.ru шлейф проверьте. Либо подкиньте с соседнего лезвия.

Просто поменять местами шлейфы ?

Splinter · 7 апр 2018, 18:56

@yaroslav1980@mail.ru У вас нет обмена с крайним лезвии Chain[5] - это то, которое подключено к разъему J6 на плате управления. Отключите это лезвие (отключите от него шлейф данных и питание) и запустите майнер с 2 оставшимися лезвиями. Если оставшиеся поднимутся, то попробуйте неисправное поставить на место исправного. Если не пойдет, то его в ремонт. Если пойдет, меняйте шлейф.

Изменено 7 апр 2018, 19:00 пользователем Splinter

yaroslav1980@mail.ru · 7 апр 2018, 19:00

3 минуты назад, Splinter сказал:

@yaroslav1980@mail.ru У вас нет обмена с МК PIC на крайнем лезвии Chain[5] - это то, которое подключено к разъему J6 на плате управления. Отключите это лезвие (отключите от него шлейф данных и питание) и запустите майнер с 2 оставшимися лезвиями. Если оставшиеся поднимутся, то попробуйте неисправное поставить на место исправного. Если не пойдет, то его в ремонт.

Простите за тупость а разъём j6 это какой ? Их же три ..

Splinter · 7 апр 2018, 19:02

8 минут назад, yaroslav1980@mail.ru сказал:

Простите за тупость а разъём j6 это какой ? Их же три ..

Потому и написал что их три. J6 подписано белой краской около разъема, смотрите внимательней. Он ближе к разъему питания.

Изменено 7 апр 2018, 19:09 пользователем Splinter

Splinter · 7 апр 2018, 21:44

7 часов назад, vladiksam сказал:

Кто знает напишите где у них датчик температуры, был бы очень благодарен. Ведь не через чипы же снимается температура?

версия платы 4.31

snowbim · 8 апр 2018, 04:17

Так случилось, что попала вода на s9, на контрольной плате окисления. Асик запускается , но в miner status пустота, сетевой диод горит , зеленые лампочки на контрольной плате горят. Больше ничего не горит. Как понять проблема в контрольной плате или все зашло глубже ?

Lee660 · 8 апр 2018, 05:45

Если вода попала только на контрольку, то проблема только в ней. Попробуйте с другого, испровного временно поставить.

sander4506 · 8 апр 2018, 07:08

@Splinter @profipc температура считывается с чипов.

snowbim · 8 апр 2018, 07:14

1 час назад, Lee660 сказал:

Если вода попала только на контрольку, то проблема только в ней. Попробуйте с другого, испровного временно поставить.

Ситуация комичная стояло 4 в ряд, над ними проходил шов плит перекрытий, сильная оттепель в пт , 4 к ряду. На одном только работает 2 из 3, попробую с неё переставить на все поочереди. Если у кого есть контролька на тест в Москве буду благодарен.

Halavshk · 8 апр 2018, 08:04

Господа железячники, у меня вопрос:
На контрольке имеется куча не распаянных разъемов под хеш-платы и вентиляторы. И еще место под какую-то БГА.
Может ли одна контролька контролировать более 3х хеш плат и двух вентиляторов?
Вопрос праздный, но любопытство мучает.

profipc · 8 апр 2018, 08:07

@Halavshk в буржуйском нете была инфа. Что можно. Народ распаивал. Править прошивку не надо. С вентилями сам лично пробовал.

Изменено 8 апр 2018, 08:11 пользователем profipc

Splinter · 8 апр 2018, 09:29

2 часа назад, snowbim сказал:

Ситуация комичная стояло 4 в ряд, над ними проходил шов плит перекрытий, сильная оттепель в пт , 4 к ряду. На одном только работает 2 из 3, попробую с неё переставить на все поочереди. Если у кого есть контролька на тест в Москве буду благодарен.

Не экспериментируйте с теми платами, которые как вы говорите "окислились". Бегите в магазин за бензином "Калоша" (только не вздумайте обычным бензином) или доставайте спирт из запасов. Берите в руки зубную щетку. Сначала щеткой насухую пройдитесь по всей плате и сдуйте всю сухую крошку окислов. Потом с бензином. Старайтесь не мочить разъемные соединения - они могут покрыться тонкой пленкой смеси говна, флюса и фиг знает чего. Если разъемы тоже окисленные, то проходите их чистой щеткой отдельно. В идеале после этого бы еще пропаять.

Я так понял сроку только двое суток как. Так что если еще не пожгли, то коррозия не должна была успеть сильно повредить плату (хотя фиг знает что там с талой водой могло быть намешано).

P.S. Если воду засосало под проц, то скорее всего таким способом ее не отчистить, нужна ультрозвуковая ванна. И не откладывайте чистку, чем дольше вы платы оставляете в таком состоянии, тем меньше шансов их восстановить.

Splinter · 8 апр 2018, 09:53

1 час назад, Halavshk сказал:

И еще место под какую-то БГА.

Если вы про мое фото несколькими постами ранее, то там просто проц снят, плата ожидает его замены. А так там нет свободных мест под BGA, все запаяны.

zoomrik · 8 апр 2018, 16:43

Всем привет, есть в наличии асик s9, на нем была сломана одна из 3х плат. Поменяли по гарантии и приехала(как утверждают) абсолютно новая. я поставил но она не работает... менял местами питание, перекидывал шлейфа к платам, делал сброс настроек. Ничего не помогло... имеет смысл менять прошивку?

bigzi · 8 апр 2018, 17:13

В 03.04.2018 в 17:47, profipc сказал:

@GLLOBUS в логе asic0. Плату в ремонт.

Нашел в его логе только "Chain[J2] has 0 asic" - вы это имели в виду?

Просто у меня так же, только J6: "Chain[J6] has 0 asic". Плату не видно, красный диод не горит, пробовал переподключения, резет и т.д и т.п. В ремонт?

log3.txt

Изменено 8 апр 2018, 17:14 пользователем bigzi

profipc · 8 апр 2018, 18:53

1 час назад, bigzi сказал:

Нашел в его логе только "Chain[J2] has 0 asic" - вы это имели в виду?

Просто у меня так же, только J6: "Chain[J6] has 0 asic". Плату не видно, красный диод не горит, пробовал переподключения, резет и т.д и т.п. В ремонт?

log3.txt

Все верно.

Splinter · 9 апр 2018, 10:42

Кто нибудь покупал интерфейсные разъемы (угловой, который на HASH плате). Никак не могу найти. Кто знает как они правильно называются, чтобы спросить у гугла?

777AV777 · 9 апр 2018, 21:42

10 часов назад, Splinter сказал:

Кто нибудь покупал интерфейсные разъемы (угловой, который на HASH плате). Никак не могу найти. Кто знает как они правильно называются, чтобы спросить у гугла?

https://m.ebay.com/itm/200Pcs-2-54mm-2x9-Pin-18-Pin-Right-Angle-Male-Shrouded-IDC-Box-Header-Connector-/172306993468?_mwBanner=1

Splinter · 10 апр 2018, 05:00

@777AV777 Спасибо, но к сожалению это не он. Это обычный IDC с шагом 2,54 мм, таких в чип-дипе полно. Тут же хитрый, с шагом 2 мм.

sergkrec85 · 10 апр 2018, 18:35

появилась новая проблема, помогите дилетанту...

kernel log.txt

жесть какая-то сначала вылетела одна плата, теперь проблема еще с одной...

vitaliy_sv · 11 апр 2018, 06:33

В 08.04.2018 в 11:17, snowbim сказал:

Так случилось, что попала вода на s9, на контрольной плате окисления. Асик запускается , но в miner status пустота, сетевой диод горит , зеленые лампочки на контрольной плате горят. Больше ничего не горит. Как понять проблема в контрольной плате или все зашло глубже ?

Посмотрите лог файл во вкладке Kernel log скопируйте его сюда я вам подскажу что у вас с майнером.

Антон Коваленко · 11 апр 2018, 10:07

S9 не завелись. Платы отображаются, хешрейт 0.

Ранее писал о проблеме. Пулы меняли, сбрасывали, прошивали.

Логи после запуска. Иногда асик заводится, и отпадает минут через 5 работы.

Скрытый текст


[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000307] ps7-ttc #0 at f0006000, irq=43
[    0.000619] Console: colour dummy device 80x30
[    0.000655] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040208] pid_max: default: 32768 minimum: 301
[    0.040438] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040460] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042618] CPU: Testing write buffer coherency: ok
[    0.042982] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043046] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043272] L310 cache controller enabled
[    0.043291] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121040] CPU1: Booted secondary processor
[    0.210227] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210358] Brought up 2 CPUs
[    0.210378] SMP: Total of 2 processors activated.
[    0.210387] CPU: All CPU(s) started in SVC mode.
[    0.211052] devtmpfs: initialized
[    0.213473] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214724] regulator-dummy: no parameters
[    0.223392] NET: Registered protocol family 16
[    0.225710] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.228013] cpuidle: using governor ladder
[    0.228027] cpuidle: using governor menu
[    0.235538] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.237086] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.237101] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.237224] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.259383] bio: create slab <bio-0> at 0
[    0.261754] vgaarb: loaded
[    0.262465] SCSI subsystem initialized
[    0.263351] usbcore: registered new interface driver usbfs
[    0.263544] usbcore: registered new interface driver hub
[    0.263773] usbcore: registered new device driver usb
[    0.264297] media: Linux media interface: v0.10
[    0.264455] Linux video capture interface: v2.00
[    0.264710] pps_core: LinuxPPS API ver. 1 registered
[    0.264722] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.264846] PTP clock support registered
[    0.265206] EDAC MC: Ver: 3.0.0
[    0.266259] Advanced Linux Sound Architecture Driver Initialized.
[    0.269236] DMA-API: preallocated 4096 debug entries
[    0.269250] DMA-API: debugging enabled by kernel config
[    0.269337] Switched to clocksource arm_global_timer
[    0.289765] NET: Registered protocol family 2
[    0.290451] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.290548] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.290707] TCP: Hash tables configured (established 8192 bind 8192)
[    0.290775] TCP: reno registered
[    0.290797] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.290850] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.291126] NET: Registered protocol family 1
[    0.291506] RPC: Registered named UNIX socket transport module.
[    0.291519] RPC: Registered udp transport module.
[    0.291527] RPC: Registered tcp transport module.
[    0.291535] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.291550] PCI: CLS 0 bytes, default 64
[    0.292010] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.294096] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.295549] bounce pool size: 64 pages
[    0.296468] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.296678] msgmni has been set to 1486
[    0.297498] io scheduler noop registered
[    0.297512] io scheduler deadline registered
[    0.297551] io scheduler cfq registered (default)
[    0.306391] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.306411] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.434974] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.007765] console [ttyPS0] enabled
[    1.012082] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.019893] [drm] Initialized drm 1.1.0 20060810
[    1.036926] brd: module loaded
[    1.046349] loop: module loaded
[    1.056044] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.061837] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.069915] libphy: XEMACPS mii bus: probed
[    1.074289] ------------- phy_id = 0x3625e62
[    1.079028] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.087887] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.094547] ehci-pci: EHCI PCI platform driver
[    1.101786] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.108588] usbcore: registered new interface driver usb-storage
[    1.115532] mousedev: PS/2 mouse device common for all mice
[    1.121733] i2c /dev entries driver
[    1.128678] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.134242] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.140187] Xilinx Zynq CpuIdle Driver started
[    1.145026] sdhci: Secure Digital Host Controller Interface driver
[    1.151151] sdhci: Copyright(c) Pierre Ossman
[    1.155462] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.162370] mmc0: no vqmmc regulator found
[    1.166385] mmc0: no vmmc regulator found
[    1.209360] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.218060] usbcore: registered new interface driver usbhid
[    1.223577] usbhid: USB HID core driver
[    1.228319] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.234621] nand: Micron MT29F2G08ABAEAWP
[    1.238585] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.244543] Bad block table found at page 131008, version 0x01
[    1.250774] Bad block table found at page 130944, version 0x01
[    1.256829] 3 ofpart partitions found on MTD device pl353-nand
[    1.262612] Creating 3 MTD partitions on "pl353-nand":
[    1.267707] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.275756] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.283088] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.292111] TCP: cubic registered
[    1.295345] NET: Registered protocol family 17
[    1.300073] Registering SWP/SWPB emulation handler
[    1.306019] regulator-dummy: disabling
[    1.310423] UBI: attaching mtd1 to ubi0
[    1.838717] UBI: scanning is finished
[    1.850439] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.857495] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.864292] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.870967] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.877805] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.883816] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.890926] UBI: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1134783803
[    1.899956] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.909154] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.909159] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.913204] ALSA device list:
[    1.913209]   No soundcards found.
[    1.929674] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.990436] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.996364] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.005507] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.015384] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.020462] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[    2.031954] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.039392] devtmpfs: mounted
[    2.042501] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.892610] random: dd urandom read with 0 bits of entropy available
[    3.289375] 
[    3.289375] bcm54xx_config_init
[    3.899401] 
[    3.899401] bcm54xx_config_init
[    6.900215] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    6.906305] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   19.600650] In axi fpga driver!
[   19.603720] request_mem_region OK!
[   19.607110] AXI fpga dev virtual address is 0xf01fe000
[   19.612247] *base_vir_addr = 0x8c510
[   19.627989] In fpga mem driver!
[   19.631130] request_mem_region OK!
[   19.634639] fpga mem virtual address is 0xf3000000
[   20.428671] 
[   20.428671] bcm54xx_config_init
[   21.058615] 
[   21.058615] bcm54xx_config_init
[   24.059107] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   24.065131] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=0008c510
miner ID : 816c350c6880881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[0] has core num=1
Chain[5] ASIC[1] has core num=1
Chain[5] ASIC[2] has core num=1
Chain[5] ASIC[3] has core num=1
Chain[5] ASIC[4] has core num=2
Chain[5] ASIC[5] has core num=1
Chain[5] ASIC[6] has core num=1
Chain[5] ASIC[7] has core num=1
Chain[5] ASIC[8] has core num=1
Chain[5] ASIC[9] has core num=2
Chain[5] ASIC[10] has core num=1
Chain[5] ASIC[11] has core num=2
Chain[5] ASIC[12] has core num=1
Chain[5] ASIC[13] has core num=15
Chain[5] ASIC[14] has core num=1
Chain[5] ASIC[15] has core num=2
Chain[5] ASIC[16] has core num=1
Chain[5] ASIC[17] has core num=2
Chain[5] ASIC[18] has core num=1
Chain[5] ASIC[19] has core num=1
Chain[5] ASIC[20] has core num=2
Chain[5] ASIC[21] has core num=1
Chain[5] ASIC[22] has core num=1
Chain[5] ASIC[23] has core num=1
Chain[5] ASIC[24] has core num=1
Chain[5] ASIC[25] has core num=1
Chain[5] ASIC[27] has core num=1
Chain[5] ASIC[28] has core num=1
Chain[5] ASIC[29] has core num=1
Chain[5] ASIC[30] has core num=1
Chain[5] ASIC[31] has core num=2
Chain[5] ASIC[32] has core num=1
Chain[5] ASIC[33] has core num=1
Chain[5] ASIC[34] has core num=1
Chain[5] ASIC[35] has core num=1
Chain[5] ASIC[36] has core num=1
Chain[5] ASIC[37] has core num=1
Chain[5] ASIC[38] has core num=1
Chain[5] ASIC[39] has core num=2
Chain[5] ASIC[40] has core num=1
Chain[5] ASIC[41] has core num=1
Chain[5] ASIC[42] has core num=2
Chain[5] ASIC[43] has core num=2
Chain[5] ASIC[44] has core num=1
Chain[5] ASIC[46] has core num=1
Chain[5] ASIC[47] has core num=1
Chain[5] ASIC[48] has core num=1
Chain[5] ASIC[49] has core num=1
Chain[5] ASIC[50] has core num=2
Chain[5] ASIC[51] has core num=1
Chain[5] ASIC[52] has core num=1
Chain[5] ASIC[53] has core num=1
Chain[5] ASIC[54] has core num=1
Chain[5] ASIC[55] has core num=1
Chain[5] ASIC[56] has core num=1
Chain[5] ASIC[57] has core num=1
Chain[5] ASIC[58] has core num=1
Chain[5] ASIC[59] has core num=1
Chain[5] ASIC[60] has core num=1
Chain[5] ASIC[61] has core num=1
Chain[5] ASIC[62] has core num=1
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[26] has core num=1
Check chain[7] PIC fw version=0x03
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=91 on chain[7], value=890
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1378 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found= 1615 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 816c350c6880881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[5] speed=4560
get fan[2] speed=6120
get fan[5] speed=4560
get fan[2] speed=6120
get fan[5] speed=4560
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=890
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=890
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=125 value=870
Chain[J7] orignal chain_voltage_pic=91 value=890
Chain[J8] orignal chain_voltage_pic=91 value=890
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[0] has core num=1
Chain[J6] ASIC[1] has core num=1
Chain[J6] ASIC[2] has core num=1
Chain[J6] ASIC[3] has core num=1
Chain[J6] ASIC[4] has core num=2
Chain[J6] ASIC[5] has core num=1
Chain[J6] ASIC[6] has core num=1
Chain[J6] ASIC[7] has core num=1
Chain[J6] ASIC[8] has core num=1
Chain[J6] ASIC[9] has core num=2
Chain[J6] ASIC[10] has core num=1
Chain[J6] ASIC[11] has core num=2
Chain[J6] ASIC[12] has core num=1
Chain[J6] ASIC[13] has core num=15
Chain[J6] ASIC[14] has core num=1
Chain[J6] ASIC[15] has core num=2
Chain[J6] ASIC[16] has core num=1
Chain[J6] ASIC[17] has core num=2
Chain[J6] ASIC[18] has core num=1
Chain[J6] ASIC[19] has core num=1
Chain[J6] ASIC[20] has core num=2
Chain[J6] ASIC[21] has core num=1
Chain[J6] ASIC[22] has core num=1
Chain[J6] ASIC[23] has core num=1
Chain[J6] ASIC[24] has core num=1
Chain[J6] ASIC[25] has core num=1
Chain[J6] ASIC[27] has core num=1
Chain[J6] ASIC[28] has core num=1
Chain[J6] ASIC[29] has core num=1
Chain[J6] ASIC[30] has core num=1
Chain[J6] ASIC[31] has core num=2
Chain[J6] ASIC[32] has core num=1
Chain[J6] ASIC[33] has core num=1
Chain[J6] ASIC[34] has core num=1
Chain[J6] ASIC[35] has core num=1
Chain[J6] ASIC[36] has core num=1
Chain[J6] ASIC[37] has core num=1
Chain[J6] ASIC[38] has core num=1
Chain[J6] ASIC[39] has core num=2
Chain[J6] ASIC[40] has core num=1
Chain[J6] ASIC[41] has core num=1
Chain[J6] ASIC[42] has core num=2
Chain[J6] ASIC[43] has core num=2
Chain[J6] ASIC[44] has core num=1
Chain[J6] ASIC[46] has core num=1
Chain[J6] ASIC[47] has core num=1
Chain[J6] ASIC[48] has core num=1
Chain[J6] ASIC[49] has core num=1
Chain[J6] ASIC[50] has core num=2
Chain[J6] ASIC[51] has core num=1
Chain[J6] ASIC[52] has core num=1
Chain[J6] ASIC[53] has core num=1
Chain[J6] ASIC[54] has core num=1
Chain[J6] ASIC[55] has core num=1
Chain[J6] ASIC[56] has core num=1
Chain[J6] ASIC[57] has core num=1
Chain[J6] ASIC[58] has core num=1
Chain[J6] ASIC[59] has core num=1
Chain[J6] ASIC[60] has core num=1
Chain[J6] ASIC[61] has core num=1
Chain[J6] ASIC[62] has core num=1
Chain[J7] has core num in PIC
Chain[J8] has core num in PIC
Chain[J8] ASIC[26] has core num=1
miner total rate=13737GH/s fixed rate=13500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=668
Asic[ 0]:668 
Asic[ 1]:668 Asic[ 2]:668 Asic[ 3]:668 Asic[ 4]:668 Asic[ 5]:668 Asic[ 6]:668 Asic[ 7]:668 Asic[ 8]:668 
Asic[ 9]:668 Asic[10]:668 Asic[11]:668 Asic[12]:668 Asic[13]:668 Asic[14]:668 Asic[15]:668 Asic[16]:668 
Asic[17]:668 Asic[18]:668 Asic[19]:668 Asic[20]:668 Asic[21]:668 Asic[22]:668 Asic[23]:668 Asic[24]:668 
Asic[25]:668 Asic[26]:668 Asic[27]:668 Asic[28]:668 Asic[29]:668 Asic[30]:668 Asic[31]:668 Asic[32]:668 
Asic[33]:668 Asic[34]:668 Asic[35]:668 Asic[36]:668 Asic[37]:668 Asic[38]:668 Asic[39]:668 Asic[40]:668 
Asic[41]:668 Asic[42]:668 Asic[43]:668 Asic[44]:668 Asic[45]:668 Asic[46]:668 Asic[47]:668 Asic[48]:668 
Asic[49]:668 Asic[50]:668 Asic[51]:668 Asic[52]:668 Asic[53]:668 Asic[54]:668 Asic[55]:668 Asic[56]:668 
Asic[57]:668 Asic[58]:668 Asic[59]:668 Asic[60]:668 Asic[61]:668 Asic[62]:668 
Chain:5 max freq=668
Chain:5 min freq=668

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=631
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631 
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631 
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631 
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631 
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631 
Chain:6 max freq=631
Chain:6 min freq=631

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=631
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631 
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631 
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631 
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631 
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631 
Chain:7 max freq=631
Chain:7 min freq=631


Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=668
Asic[ 0]:650 
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Detect a bad chip=13 on chain[5], fixed to 400M
Asic[13]:668 Asic[14]:650 Asic[15]:650 Asic[16]:650 
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 
Asic[25]:650 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656 
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656 
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656 
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656 
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656 
Chain:5 max freq=668
Chain:5 min freq=650

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=631
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631 
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631 
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631 
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631 
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631 
Chain:6 max freq=631
Chain:6 min freq=631

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=631
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631 
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631 
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631 
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631 
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631 
Chain:7 max freq=631
Chain:7 min freq=631

max freq = 668
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:57 remote:60 offset:30 
Chain[J6] chip[244] get middle temp offset=30 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:52 remote:55 offset:29 
Chain[J7] chip[244] get middle temp offset=29 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:49 remote:52 offset:29 
Chain[J8] chip[244] get middle temp offset=29 typeID=55
single board rate=4573 voltage limit=890 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 890
retryFlag=1 will set the voltage limited on chain[5], change voltage=890
now set pic voltage=91 on chain[5]
single board rate=4531 voltage limit=890 on chain[6]
get PIC voltage=890 on chain[6], check: must be < 890
retryFlag=1 will set the voltage limited on chain[6], change voltage=890
now set pic voltage=91 on chain[6]
single board rate=4531 voltage limit=890 on chain[7]
get PIC voltage=890 on chain[7], check: must be < 890
retryFlag=1 will set the voltage limited on chain[7], change voltage=890
now set pic voltage=91 on chain[7]
Chain[J6] set working voltage=890 [91]
Chain[J7] set working voltage=890 [91]
Chain[J8] set working voltage=890 [91]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=30
Chain[5] Chip[62] local Temp=75
Chain[5] Chip[62] middle Temp=89
Special fix Chain[5] Chip[62] middle Temp = 90
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=29
Chain[6] Chip[62] local Temp=70
Chain[6] Chip[62] middle Temp=82
Special fix Chain[6] Chip[62] middle Temp = 85
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=29
Chain[7] Chip[62] local Temp=68
Chain[7] Chip[62] middle Temp=82
Special fix Chain[7] Chip[62] middle Temp = 83
Done read temp on Chain[7]
set FAN speed according to: temp_highest=75 temp_top1[PWM_T]=75 temp_top1[TEMP_POS_LOCAL]=75 temp_change=1 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=0

Логи при обвале

Скрытый текст


[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000314] ps7-ttc #0 at df804000, irq=43
[    0.000626] Console: colour dummy device 80x30
[    0.000659] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040209] pid_max: default: 32768 minimum: 301
[    0.040438] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040457] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042623] CPU: Testing write buffer coherency: ok
[    0.042972] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043031] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043256] L310 cache controller enabled
[    0.043276] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121041] CPU1: Booted secondary processor
[    0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210365] Brought up 2 CPUs
[    0.210384] SMP: Total of 2 processors activated.
[    0.210393] CPU: All CPU(s) started in SVC mode.
[    0.211089] devtmpfs: initialized
[    0.213494] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214751] regulator-dummy: no parameters
[    0.223767] NET: Registered protocol family 16
[    0.226081] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.228393] cpuidle: using governor ladder
[    0.228406] cpuidle: using governor menu
[    0.235923] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.237457] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.237471] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.237590] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.259666] bio: create slab <bio-0> at 0
[    0.261419] vgaarb: loaded
[    0.262145] SCSI subsystem initialized
[    0.263047] usbcore: registered new interface driver usbfs
[    0.263219] usbcore: registered new interface driver hub
[    0.263449] usbcore: registered new device driver usb
[    0.263980] media: Linux media interface: v0.10
[    0.264140] Linux video capture interface: v2.00
[    0.264393] pps_core: LinuxPPS API ver. 1 registered
[    0.264405] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.264537] PTP clock support registered
[    0.264903] EDAC MC: Ver: 3.0.0
[    0.265972] Advanced Linux Sound Architecture Driver Initialized.
[    0.269001] DMA-API: preallocated 4096 debug entries
[    0.269014] DMA-API: debugging enabled by kernel config
[    0.269106] Switched to clocksource arm_global_timer
[    0.290350] NET: Registered protocol family 2
[    0.291033] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.291092] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.291177] TCP: Hash tables configured (established 4096 bind 4096)
[    0.291230] TCP: reno registered
[    0.291250] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.291282] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.291533] NET: Registered protocol family 1
[    0.291877] RPC: Registered named UNIX socket transport module.
[    0.291890] RPC: Registered udp transport module.
[    0.291898] RPC: Registered tcp transport module.
[    0.291907] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.291920] PCI: CLS 0 bytes, default 64
[    0.292371] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.294435] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.296638] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.296832] msgmni has been set to 967
[    0.297639] io scheduler noop registered
[    0.297652] io scheduler deadline registered
[    0.297693] io scheduler cfq registered (default)
[    0.307077] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.307098] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.432788] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.000064] console [ttyPS0] enabled
[    1.004350] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.011987] [drm] Initialized drm 1.1.0 20060810
[    1.029169] brd: module loaded
[    1.038616] loop: module loaded
[    1.048211] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.054343] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.062316] libphy: XEMACPS mii bus: probed
[    1.066684] ------------- phy_id = 0x3625e62
[    1.071677] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.080319] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.086939] ehci-pci: EHCI PCI platform driver
[    1.094185] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.101024] usbcore: registered new interface driver usb-storage
[    1.107887] mousedev: PS/2 mouse device common for all mice
[    1.114034] i2c /dev entries driver
[    1.120998] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.126487] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.132403] Xilinx Zynq CpuIdle Driver started
[    1.137246] sdhci: Secure Digital Host Controller Interface driver
[    1.143399] sdhci: Copyright(c) Pierre Ossman
[    1.147684] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.154509] mmc0: no vqmmc regulator found
[    1.158520] mmc0: no vmmc regulator found
[    1.199124] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.207813] usbcore: registered new interface driver usbhid
[    1.213322] usbhid: USB HID core driver
[    1.218046] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.224339] nand: Micron MT29F2G08ABAEAWP
[    1.228307] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.234249] Bad block table found at page 131008, version 0x01
[    1.240472] Bad block table found at page 130944, version 0x01
[    1.246526] 3 ofpart partitions found on MTD device pl353-nand
[    1.252305] Creating 3 MTD partitions on "pl353-nand":
[    1.257397] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.265463] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.272806] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.281833] TCP: cubic registered
[    1.285067] NET: Registered protocol family 17
[    1.289794] Registering SWP/SWPB emulation handler
[    1.295708] regulator-dummy: disabling
[    1.300104] UBI: attaching mtd1 to ubi0
[    1.824466] UBI: scanning is finished
[    1.836150] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.843233] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.849995] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.856660] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.863538] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.869518] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.876626] UBI: max/mean erase counter: 47/23, WL threshold: 4096, image sequence number: 1283732989
[    1.885842] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.895059] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.895064] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.899073] ALSA device list:
[    1.899077]   No soundcards found.
[    1.915530] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.986843] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.992799] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.001903] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.011791] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.016821] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model
[    2.028390] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.035826] devtmpfs: mounted
[    2.038939] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.879056] random: dd urandom read with 0 bits of entropy available
[    3.279128] 
[    3.279128] bcm54xx_config_init
[    3.889129] 
[    3.889129] bcm54xx_config_init
[    6.889981] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    6.896074] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   19.383355] In axi fpga driver!
[   19.386425] request_mem_region OK!
[   19.389847] AXI fpga dev virtual address is 0xdf9fc000
[   19.394923] *base_vir_addr = 0x8c510
[   19.410316] In fpga mem driver!
[   19.413386] request_mem_region OK!
[   19.416950] fpga mem virtual address is 0xe2000000
[   20.198479] 
[   20.198479] bcm54xx_config_init
[   20.828392] 
[   20.828392] bcm54xx_config_init
[   23.828897] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   23.834915] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  402.269242] random: nonblocking pool is initialized
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 8014650c68808814
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[26] has core num=1
Chain[5] ASIC[47] has core num=8
Chain[5] ASIC[48] has core num=2
Chain[5] ASIC[54] has core num=4
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[42] has core num=1
Chain[6] ASIC[53] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[26] has core num=2
Chain[7] ASIC[32] has core num=1
Chain[7] ASIC[53] has core num=4
Check chain[7] PIC fw version=0x03
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=91 on chain[7], value=890
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1375 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:37:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 8014650c68808814
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[5] speed=4560
get fan[2] speed=6120
get fan[5] speed=4560
get fan[2] speed=6120
get fan[5] speed=4560
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=890
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=870
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=91 value=890
Chain[J6] will use backup chain_voltage_pic=870 [125]
Chain[J6] get working chain_voltage_pic=125
Chain[J7] orignal chain_voltage_pic=91 value=890
Chain[J8] orignal chain_voltage_pic=91 value=890
Chain[J8] will use backup chain_voltage_pic=870 [125]
Chain[J8] get working chain_voltage_pic=125
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[26] has core num=1
Chain[J6] ASIC[47] has core num=8
Chain[J6] ASIC[48] has core num=2
Chain[J6] ASIC[54] has core num=4
Chain[J7] has core num in PIC
Chain[J7] ASIC[42] has core num=1
Chain[J7] ASIC[53] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[26] has core num=2
Chain[J8] ASIC[32] has core num=1
Chain[J8] ASIC[53] has core num=4
miner total rate=13938GH/s fixed rate=13500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=656
Asic[ 0]:656 
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656 
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656 
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656 
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656 
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656 
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656 
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656 
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656 
Chain:5 max freq=656
Chain:5 min freq=656

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=631
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631 
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631 
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631 
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631 
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631 
Chain:6 max freq=631
Chain:6 min freq=631

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=656
Asic[ 0]:656 
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656 
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656 
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656 
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656 
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656 
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656 
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656 
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656 
Chain:7 max freq=656
Chain:7 min freq=656


Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=656
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637 
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637 
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637 
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637 
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637 
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637 
Chain:5 max freq=637
Chain:5 min freq=631

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=631
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631 
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631 
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631 
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631 
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631 
Chain:6 max freq=631
Chain:6 min freq=631

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=656
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637 
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637 
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637 
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637 
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637 
Chain:7 max freq=637
Chain:7 min freq=631

max freq = 637
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:37 remote:41 offset:27 
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:36 remote:39 offset:28 
Chain[J7] chip[244] get middle temp offset=28 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:36 remote:39 offset:28 
Chain[J8] chip[244] get middle temp offset=28 typeID=55
single board rate=4552 voltage limit=890 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 890
single board rate=4530 voltage limit=890 on chain[6]
get PIC voltage=890 on chain[6], check: must be < 890
single board rate=4553 voltage limit=890 on chain[7]
get PIC voltage=870 on chain[7], check: must be < 890
Chain[J6] set working voltage=870 [125]
Chain[J7] set working voltage=890 [91]
Chain[J8] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=631	freq[01]=631	freq[02]=631	freq[03]=631	freq[04]=631	freq[05]=631	freq[06]=631	freq[07]=631	
freq[08]=631	freq[09]=631	freq[10]=631	freq[11]=631	freq[12]=631	freq[13]=631	freq[14]=631	freq[15]=631	
freq[16]=631	freq[17]=631	freq[18]=631	freq[19]=637	freq[20]=637	freq[21]=637	freq[22]=637	freq[23]=637	
freq[24]=637	freq[25]=637	freq[26]=637	freq[27]=637	freq[28]=637	freq[29]=637	freq[30]=637	freq[31]=637	
freq[32]=637	freq[33]=637	freq[34]=637	freq[35]=637	freq[36]=637	freq[37]=637	freq[38]=637	freq[39]=637	
freq[40]=637	freq[41]=637	freq[42]=637	freq[43]=637	freq[44]=637	freq[45]=637	freq[46]=637	freq[47]=637	
freq[48]=637	freq[49]=637	freq[50]=637	freq[51]=637	freq[52]=637	freq[53]=637	freq[54]=637	freq[55]=637	
freq[56]=637	freq[57]=637	freq[58]=637	freq[59]=637	freq[60]=637	freq[61]=637	freq[62]=637	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26032
last_nonce_num:29211
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=631	freq[01]=631	freq[02]=631	freq[03]=631	freq[04]=631	freq[05]=631	freq[06]=631	freq[07]=631	
freq[08]=631	freq[09]=631	freq[10]=631	freq[11]=631	freq[12]=631	freq[13]=631	freq[14]=631	freq[15]=631	
freq[16]=631	freq[17]=631	freq[18]=631	freq[19]=631	freq[20]=631	freq[21]=631	freq[22]=631	freq[23]=631	
freq[24]=631	freq[25]=631	freq[26]=631	freq[27]=631	freq[28]=631	freq[29]=631	freq[30]=631	freq[31]=631	
freq[32]=631	freq[33]=631	freq[34]=631	freq[35]=631	freq[36]=631	freq[37]=631	freq[38]=631	freq[39]=631	
freq[40]=631	freq[41]=631	freq[42]=631	freq[43]=631	freq[44]=631	freq[45]=631	freq[46]=631	freq[47]=631	
freq[48]=631	freq[49]=631	freq[50]=631	freq[51]=631	freq[52]=631	freq[53]=631	freq[54]=631	freq[55]=631	
freq[56]=631	freq[57]=631	freq[58]=631	freq[59]=631	freq[60]=631	freq[61]=631	freq[62]=631	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25854
last_nonce_num:36327
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=631	freq[01]=631	freq[02]=631	freq[03]=631	freq[04]=631	freq[05]=631	freq[06]=631	freq[07]=631	
freq[08]=631	freq[09]=631	freq[10]=631	freq[11]=631	freq[12]=631	freq[13]=631	freq[14]=631	freq[15]=631	
freq[16]=631	freq[17]=631	freq[18]=631	freq[19]=631	freq[20]=631	freq[21]=631	freq[22]=631	freq[23]=631	
freq[24]=631	freq[25]=637	freq[26]=637	freq[27]=637	freq[28]=637	freq[29]=637	freq[30]=637	freq[31]=637	
freq[32]=637	freq[33]=637	freq[34]=637	freq[35]=637	freq[36]=637	freq[37]=637	freq[38]=637	freq[39]=637	
freq[40]=637	freq[41]=637	freq[42]=637	freq[43]=637	freq[44]=637	freq[45]=637	freq[46]=637	freq[47]=637	
freq[48]=637	freq[49]=637	freq[50]=637	freq[51]=637	freq[52]=637	freq[53]=637	freq[54]=637	freq[55]=637	
freq[56]=637	freq[57]=637	freq[58]=637	freq[59]=637	freq[60]=637	freq[61]=637	freq[62]=637	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26006
last_nonce_num:43458
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: OK!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: OK!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: OK!
setStartTimePoint total_tv_start_sys=161 total_tv_end_sys=162
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[5]: (asic index start from 1-63)

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=74.5410 Asic[02]=69.5580 Asic[03]=69.2730 Asic[04]=68.5510 Asic[05]=71.3360 Asic[06]=72.1420 Asic[07]=9.29400 Asic[08]=74.5410 
Asic[09]=69.1050 Asic[10]=75.7320 Asic[11]=69.2890 Asic[12]=71.2860 Asic[13]=67.2090 Asic[14]=72.2760 Asic[15]=69.9940 Asic[16]=71.3360 
Asic[17]=69.9270 Asic[18]=71.3030 Asic[19]=73.2490 Asic[20]=72.3930 Asic[21]=72.1250 Asic[22]=70.4130 Asic[23]=73.6180 Asic[24]=69.0550 
Asic[25]=76.5040 Asic[26]=74.3900 Asic[27]=66.9070 Asic[28]=74.3900 Asic[29]=68.6690 Asic[30]=73.5000 Asic[31]=69.5080 Asic[32]=68.6850 
Asic[33]=75.8160 Asic[34]=69.2560 Asic[35]=67.2930 Asic[36]=51.0020 Asic[37]=69.4570 Asic[38]=57.5450 Asic[39]=69.0380 Asic[40]=40.0970 
Asic[41]=67.4940 Asic[42]=72.2930 Asic[43]=30.4840 Asic[44]=73.7350 Asic[45]=76.0670 Asic[46]=72.0410 Asic[47]=59.5920 Asic[48]=2.18100 
Asic[49]=72.1580 Asic[50]=74.8930 Asic[51]=69.7930 Asic[52]=68.5510 Asic[53]=2.29800 Asic[54]=71.3530 Asic[55]=17.9180 Asic[56]=55.4650 
Asic[57]=68.4510 
get RT hashrate from Chain[7]: (asic index start from 1-63)
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=27
read failed, old value: Chain[5] Chip[62] local Temp=71
read failed on Chain[5] Chip[62] middle Temp old value:86
Special fix Chain[5] Chip[62] middle Temp = 86
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=28
Chain[6] Chip[62] local Temp=61
Chain[6] Chip[62] middle Temp=71
Special fix Chain[6] Chip[62] middle Temp = 76
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=28
read failed, old value: Chain[7] Chip[62] local Temp=66
read failed on Chain[7] Chip[62] middle Temp old value:81
Special fix Chain[7] Chip[62] middle Temp = 81
Done read temp on Chain[7]
Set fixed full fan speed
FAN PWM: 100
read_temp_func Done!
CRC error counter=0

При обвале на одной плате идут HW по одной плате.

Кто подскажет где копать?

Изменено 11 апр 2018, 10:18 пользователем Антон Коваленко

Splinter · 11 апр 2018, 16:16

@Антон Коваленко Странные логи у вас. В них разные платы в разъеме J6? У них разные таблицы плохих чипов и частот. В первом логе вообще все чипы на этой плате помечены как плохие, при этом частоты стоят самые высокие. Первый лог обрезан? Там не хватает части с тестированием хэширования. Во втором нормально отрабатывает только средняя плата, с двух других после пробного хеширования не читается температура и RT hashrate. Такое ощущение, что платы отваливаются после прогрева. В последнем случае, если оставить одну среднюю плату, то она должна работать. Блок питания используете заведомо исправный?

В логах полная каша, тестируйте каждую плату по отдельности - так легче будет разобраться.

yaroslav1980@mail.ru · 11 апр 2018, 18:04

В 07.04.2018 в 22:02, Splinter сказал:

Потому и написал что их три. J6 подписано белой краской около разъема, смотрите внимательней. Он ближе к разъему питания.

В сервисе поменяли контрольку и все завелось .... оказалось дело в ней ((Можно ли починить старую ? Или сразу покупать другую а эту выкинуть ? Она ведь стартует и даже че то показывает ... есть у кого нибудь опыт перепрошивки быть может ?

Ремонт: Bitmain Antminer s7, s9, l3+

Рекомендуемые сообщения

Ссылка на комментарий

Поделиться на другие сайты

Топ авторов темы

Популярные дни

Топ авторов темы

Популярные дни

Популярные посты

alexey7mechanic

adv

adv

Изображения в теме

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Для публикации сообщений создайте учётную запись или авторизуйтесь

Создать учетную запись

Войти

Последние посетители 0 пользователей онлайн

Similar Topics

Ресурсы

О Форуме

Соц.сети

Почта