Ремонт: Bitmain Antminer s7, s9, l3+

[dimmm]

Скрытый текст

bring up chain 1
2020-01-16 06:32:01 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffa
2020-01-16 06:32:33 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fff8
2020-01-16 06:32:34 driver-btm-soc.c:3810:check_asic_num: without pre_open_core chain 1, find asic num = 60

По всем платам посмотри.

[dimmm]

3 минуты назад, kias сказал:

2020-01-23 09:11:49 dspic33ep16gs202.c:158:dsPIC33EP16GS202_reset_pic: ERROR! failed on Chain[1] after 3 times try!

смотри среднюю плату если шлейфы подряд подключены.

прошей пик .Что то в нём.

[kias]

Спасибо dimmm все получилось, был трабл c pic тоже не пойму пока почему, я его pickit 3 все вроде нормально без ошибок заливал, но он почему то не заработал. Буду пытаться сливать прошивку c ATH812, дальше разбираться че к чему, трупов s9k хватает есть на чем тренироваться. 

[dimmm]

1 минуту назад, kias сказал:

трупов s9k хватает

Аналогично Выгорают жуть.

[Splinter]

9 часов назад, Rómulo Gil сказал:

firmware pic16f1704 en la placa hash s9, Pickit 3, descarga MPLAB IPE v4.15 desde el sitio de microchip.

Puedo leer y
puedo borrar el chip. Luego importo el firmware de una buena placa con la misma versión de v4.21. Cuando intento programar ... falla

 

Используйте MPLAB X IPE v5.20. В Advanced Mode перейдите в раздел Power.  VDD = 3.3V, установите Power target circuit from Tool. Подключите плату только к PicKit3, без дополнительного питания. Читайте/пишите PIC.

[Rómulo Gil]

3 часа назад, Splinter сказал:

Utilice MPLAB X IPE v5.20. En modo avanzado, vaya a la sección de energía. VDD = 3.3V, establezca el circuito de destino de potencia desde la herramienta Conecte la placa solo a PicKit3, sin alimentación adicional. Leer / Escribir PIC.

Я следую указанным шагам

показал это сообщение

 

Я изменил напряжение до 4,675 вольт

 

Последовательная схема выполняемых процессов. У меня все еще есть ошибка Pic Flash. Импортированная прошивка от той же версии платы. Спасибо за все ваше внимание.

 

 

[Splinter]

@Rómulo Gil Должно все работать при 3.3В, если подать больше то может сгореть схема. Программатор сообщает что USB порт не тянет. Это значит что либо хэшплата потребляет по линии 3.3В больше чем нужно (неисправность), либо вы подключаете программатор к слабому USB порту (напрмер, через USB хаб).

Что касается того, что хэш-плата после прошивки не видится платой управления - прикрепите к сообщению hex-дам памяти PIC этой платы.

[Petr4]

Добрый день! Подскажите пожалуйста какой прошивкой лучше искать неисправные чипы. Или какие еще варианты?

я про antminer s9

 

[kias]

Подскажите кто знанет нумерацию чипов на S11_20  плата BHB7501

[babus]

Ребят вопрос немного не по теме, кто нибудь знает как расположены чипы на плате antminer s17?

Изменено 30 янв 2020, 14:39 пользователем babus

[DemoN071]

Народ помогите понять куда копать,асик s9k неработает одна плата?

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203696K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25680K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12640K (ccea9000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Broadcom BCM5241 e000b000.etherne:00: attached PHY driver [Broadcom BCM5241] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 21/10, WL threshold: 4096, image sequence number: 1562532237
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 4A1FE789-2482-407F-81B0-3DA9FF3C2E2D, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 209/77, WL threshold: 4096, image sequence number: 2511544773
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID B72BFACA-01E2-4DDA-9D1B-61292F81B174, small LPT model
alloc_contig_range: [e043, e044) PFNs busy
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
alloc_contig_range: [e043, e044) PFNs busy
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
 [2020-01-31 14:39:37.181] httpListenThread start ret=0
 [2020-01-31 14:40:07.182] start listen on 6060 ...
 [2020-01-31 14:44:47.279] setStartTimePoint total_tv_start_sys=350 total_tv_end_sys=351

2020-01-31 14:39:37 driver-btm-soc.c:6298:bitmain_soc_init: This is Antminer S9k scan user version
2020-01-31 14:39:37 driver-btm-soc.c:6304:bitmain_soc_init: special mode: disabled
2020-01-31 14:39:37 driver-btm-soc.c:6311:bitmain_soc_init: This is high performance mode
2020-01-31 14:39:37 driver-btm-soc.c:6316:bitmain_soc_init: last commit version: 5914201 commit time: 2019-09-29 11:57:01 build: 2019-09-29 15:32:19
2020-01-31 14:39:37 driver-btm-soc.c:6337:bitmain_soc_init: Detect 256MB control board of XILINX
2020-01-31 14:39:37 driver-btm-soc.c:6340:bitmain_soc_init: Miner compile time: Sun Sep 29 15:25:10 CST 2019 type: Antminer S9k
2020-01-31 14:39:37 driver-btm-soc.c:849:check_chain: get_hash_on_plug is 0x7
2020-01-31 14:39:37 driver-btm-soc.c:861:check_chain: !! chain[0]is exist
2020-01-31 14:39:37 driver-btm-soc.c:861:check_chain: !! chain[1]is exist
2020-01-31 14:39:37 driver-btm-soc.c:861:check_chain: !! chain[2]is exist
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fc 28 fc ff
00000080 ff ff ff ff ff ff ff c3   49 49 49 49 49 49 49 49
00000090 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000a0 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000b0 49 49 49 49 49 49 49 49   49 49 49 49 49 49 49 49
000000c0 49 49 49 49 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff 97 10 00 00   00 ff ff ff 39 10 44 c9
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fb 28 fc ff
00000080 ff ff ff ff ff ff ff c3   4d 4d 4d 4d 4d 4d 4d 4d
00000090 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000a0 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000b0 4d 4d 4d 4d 4d 4d 4d 4d   4d 4d 4d 4d 4d 4d 4d 4d
000000c0 4d 4d 4d 4d 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff b4 12 00 00   00 ff ff ff 39 10 1d 16
         00 01 02 03 04 05 06 07   08 09 0A 0B 0C 0D 0E 0F
00000000 7e ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000010 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff   ff 01 02 1f fb 28 fd ff
00000080 ff ff ff ff ff ff ff c3   4b 4b 4b 4b 4b 4b 4b 4b
00000090 4b 4b 4b 4b 4b 4b 4b 4b   4b 4b 4b 4b 4b 4b 4b 4b
000000a0 4b 4b 4b 4b 4b 4b 4b 4b   4b 4b 4b 4b 4b 4b 4b 4b
000000b0 4b 4b 4b 4b 4b 4b 4b 4b   4b 4b 4b 4b 4b 4b 4b 4b
000000c0 4b 4b 4b 4b 00 ff ff ff   ff ff ff ff ff ff ff ff
000000d0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000e0 ff ff ff ff ff ff ff ff   ff ff ff ff ff ff ff ff
000000f0 ff ff ff ff fc 11 00 00   00 ff ff ff 39 10 e3 ab

read chain[0] hardware info:
major type: 0
minor type: 0
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

read chain[1] hardware info:
major type: 0
minor type: 0
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

read chain[2] hardware info:
major type: 0
minor type: 0
chip level: 0
bom version: 0x10
pcb version: 0x39
fixture 8pattern result: L0

sweep config for eco mode: 
sweep_start_voltage: 9.25
max_aging_voltage:   9.65
sweep_min_freq:      300M
sweep_max_freq:      350M

sweep config for hpf mode: 
sweep_start_voltage: 9.90
max_aging_voltage:   10.30
sweep_min_freq:      355M
sweep_max_freq:      385M
2020-01-31 14:39:48 driver-btm-soc.c:5757:get_freq_result_from_eeprom: orginal chip freq: 
chain 0 freq:
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 
365 365 365 365 365 365 365 365 365 365 

chain 1 freq:
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 
385 385 385 385 385 385 385 385 385 385 

chain 2 freq:
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 
375 375 375 375 375 375 375 375 375 375 

2020-01-31 14:39:48 driver-btm-soc.c:6430:bitmain_soc_init: reset all...
2020-01-31 14:39:50 driver-btm-soc.c:6438:bitmain_soc_init: miner ID : 806c442a18c08854
2020-01-31 14:39:50 driver-btm-soc.c:6099:init_miner_version: FPGA Version = 0xB00D
2020-01-31 14:40:10 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[0] PIC software version: 177
2020-01-31 14:40:11 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[1] PIC software version: 177
2020-01-31 14:40:11 dspic33ep16gs202.c:486:get_pic_software_version_all_chain: chain[2] PIC software version: 177
2020-01-31 14:40:11 power.c:185:power_init: power init ... 
2020-01-31 14:40:11 driver-btm-soc.c:4864:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[0] eeprom
2020-01-31 14:40:11 power.c:232:set_working_voltage_by_chain: chain[0] working_voltage = 9.90
2020-01-31 14:40:11 driver-btm-soc.c:4864:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[1] eeprom
2020-01-31 14:40:11 power.c:232:set_working_voltage_by_chain: chain[1] working_voltage = 9.90
2020-01-31 14:40:11 driver-btm-soc.c:4864:get_working_voltage_from_eeprom: get working vol [ 9.90] from chain[2] eeprom
2020-01-31 14:40:11 power.c:232:set_working_voltage_by_chain: chain[2] working_voltage = 9.90
2020-01-31 14:40:11 driver-btm-soc.c:5547:update_highest_voltage: chain 0 hpf working voltage 9.90
2020-01-31 14:40:11 driver-btm-soc.c:5547:update_highest_voltage: chain 1 hpf working voltage 9.90
2020-01-31 14:40:11 driver-btm-soc.c:5547:update_highest_voltage: chain 2 hpf working voltage 9.90
2020-01-31 14:40:11 driver-btm-soc.c:5556:update_highest_voltage: open core at max voltage 10.20
2020-01-31 14:40:11 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[0] setting to highest voltage: 10.20 ...
2020-01-31 14:40:12 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 
2020-01-31 14:40:12 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[1] setting to highest voltage: 10.20 ...
2020-01-31 14:40:14 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 
2020-01-31 14:40:14 power.c:781:set_iic_power_to_highest_voltage_by_chain: chain[2] setting to highest voltage: 10.20 ...
2020-01-31 14:40:15 power.c:707:set_iic_power_by_voltage: now setting voltage to : 10.20 
2020-01-31 14:40:16 driver-btm-soc.c:1259:get_ideal_hash_rate: get ideal hash rate 13500
2020-01-31 14:40:16 eeprom.c:675:travel_eeprom_store: chain[0] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:365 IC[001]:365 IC[002]:365 IC[003]:365 IC[004]:365 IC[005]:365 IC[006]:365 IC[007]:365 IC[008]:365 IC[009]:365 
IC[010]:365 IC[011]:365 IC[012]:365 IC[013]:365 IC[014]:365 IC[015]:365 IC[016]:365 IC[017]:365 IC[018]:365 IC[019]:365 
IC[020]:365 IC[021]:365 IC[022]:365 IC[023]:365 IC[024]:365 IC[025]:365 IC[026]:365 IC[027]:365 IC[028]:365 IC[029]:365 
IC[030]:365 IC[031]:365 IC[032]:365 IC[033]:365 IC[034]:365 IC[035]:365 IC[036]:365 IC[037]:365 IC[038]:365 IC[039]:365 
IC[040]:365 IC[041]:365 IC[042]:365 IC[043]:365 IC[044]:365 IC[045]:365 IC[046]:365 IC[047]:365 IC[048]:365 IC[049]:365 
IC[050]:365 IC[051]:365 IC[052]:365 IC[053]:365 IC[054]:365 IC[055]:365 IC[056]:365 IC[057]:365 IC[058]:365 IC[059]:365 
voltage in mode2: 9.90 V
hash rate in mode2: 04247 GH/s

2020-01-31 14:40:16 eeprom.c:675:travel_eeprom_store: chain[1] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:385 IC[001]:385 IC[002]:385 IC[003]:385 IC[004]:385 IC[005]:385 IC[006]:385 IC[007]:385 IC[008]:385 IC[009]:385 
IC[010]:385 IC[011]:385 IC[012]:385 IC[013]:385 IC[014]:385 IC[015]:385 IC[016]:385 IC[017]:385 IC[018]:385 IC[019]:385 
IC[020]:385 IC[021]:385 IC[022]:385 IC[023]:385 IC[024]:385 IC[025]:385 IC[026]:385 IC[027]:385 IC[028]:385 IC[029]:385 
IC[030]:385 IC[031]:385 IC[032]:385 IC[033]:385 IC[034]:385 IC[035]:385 IC[036]:385 IC[037]:385 IC[038]:385 IC[039]:385 
IC[040]:385 IC[041]:385 IC[042]:385 IC[043]:385 IC[044]:385 IC[045]:385 IC[046]:385 IC[047]:385 IC[048]:385 IC[049]:385 
IC[050]:385 IC[051]:385 IC[052]:385 IC[053]:385 IC[054]:385 IC[055]:385 IC[056]:385 IC[057]:385 IC[058]:385 IC[059]:385 
voltage in mode2: 9.90 V
hash rate in mode2: 04788 GH/s

2020-01-31 14:40:16 eeprom.c:675:travel_eeprom_store: chain[2] data in eeprom is:
magic number: 0x7e
freq data per ASIC:
IC[000]:1275 IC[001]:1275 IC[002]:1275 IC[003]:1275 IC[004]:1275 IC[005]:1275 IC[006]:1275 IC[007]:1275 IC[008]:1275 IC[009]:1275 
IC[010]:1275 IC[011]:1275 IC[012]:1275 IC[013]:1275 IC[014]:1275 IC[015]:1275 IC[016]:1275 IC[017]:1275 IC[018]:1275 IC[019]:1275 
IC[020]:1275 IC[021]:1275 IC[022]:1275 IC[023]:1275 IC[024]:1275 IC[025]:1275 IC[026]:1275 IC[027]:1275 IC[028]:1275 IC[029]:1275 
IC[030]:1275 IC[031]:1275 IC[032]:1275 IC[033]:1275 IC[034]:1275 IC[035]:1275 IC[036]:1275 IC[037]:1275 IC[038]:1275 IC[039]:1275 
IC[040]:1275 IC[041]:1275 IC[042]:1275 IC[043]:1275 IC[044]:1275 IC[045]:1275 IC[046]:1275 IC[047]:1275 IC[048]:1275 IC[049]:1275 
IC[050]:1275 IC[051]:1275 IC[052]:1275 IC[053]:1275 IC[054]:1275 IC[055]:1275 IC[056]:1275 IC[057]:1275 IC[058]:1275 IC[059]:1275 
voltage: 11.10 V
hash rate: -0001 GH/s

freq data per ASIC in mode2:
IC[000]:375 IC[001]:375 IC[002]:375 IC[003]:375 IC[004]:375 IC[005]:375 IC[006]:375 IC[007]:375 IC[008]:375 IC[009]:375 
IC[010]:375 IC[011]:375 IC[012]:375 IC[013]:375 IC[014]:375 IC[015]:375 IC[016]:375 IC[017]:375 IC[018]:375 IC[019]:375 
IC[020]:375 IC[021]:375 IC[022]:375 IC[023]:375 IC[024]:375 IC[025]:375 IC[026]:375 IC[027]:375 IC[028]:375 IC[029]:375 
IC[030]:375 IC[031]:375 IC[032]:375 IC[033]:375 IC[034]:375 IC[035]:375 IC[036]:375 IC[037]:375 IC[038]:375 IC[039]:375 
IC[040]:375 IC[041]:375 IC[042]:375 IC[043]:375 IC[044]:375 IC[045]:375 IC[046]:375 IC[047]:375 IC[048]:375 IC[049]:375 
IC[050]:375 IC[051]:375 IC[052]:375 IC[053]:375 IC[054]:375 IC[055]:375 IC[056]:375 IC[057]:375 IC[058]:375 IC[059]:375 
voltage in mode2: 9.90 V
hash rate in mode2: 04604 GH/s

2020-01-31 14:40:16 driver-btm-soc.c:6481:bitmain_soc_init: fan_eft : 0  fan_pwm : 0
2020-01-31 14:40:16 driver-btm-soc.c:6128:bring_up_chain: 

bring up chain 0
2020-01-31 14:40:16 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2020-01-31 14:40:48 zynq.c:212:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2020-01-31 14:40:49 driver-btm-soc.c:3794:check_asic_num: without pre_open_core chain 0, find asic num = 60
2020-01-31 14:40:53 driver-btm-soc.c:4617:set_freq_by_chain: chain[0] set freq:100.00
2020-01-31 14:40:53 driver-btm-soc.c:3840:open_core_BM1393_pre_open: pre open core = 13
2020-01-31 14:40:53 driver-btm-soc.c:3720:pre_open_core_one_chain: for chain 0
2020-01-31 14:40:53 temperature.c:591:is_eeprom_tempsensor_data_correct: check sensor info

Изменено 31 янв 2020, 18:13 пользователем DemoN071
Не могу

[Splinter]

 

33 минуты назад, DemoN071 сказал:

2020-01-31 14:42:08 driver-btm-soc.c:3794:check_asic_num: without pre_open_core chain 2, find asic num = 0

33 минуты назад, DemoN071 сказал:

Народ помогите понять куда копать,асик s9k неработает одна плата?

В сторону сервиса.

И спрячьте лог под спойлер или прикрепите текстовым файлом.

[DemoN071]

2 часа назад, Splinter сказал:

 

В сторону сервиса.

И спрячьте лог под спойлер или прикрепите текстовым файлом.

Асик или плату?

[Ishtulov]

Приветствую ребята.

Изменено 8 фев 2020, 12:04 пользователем Ishtulov

[Splinter]

14 часов назад, DemoN071 сказал:

Асик или плату?

Это уже зависит от сервиса. Обычно достаточно отдать в ремонт только неисправную плату. 

[megabits]

Видел у китайцев универсальный (S9 T9 S11 S15 T15 S17 T17) тестер хешплат. Контролька там вроде CTRL_C44  ver v1.3010, я так понимаю нужен только UART шнур и прошивка  к на контрольку (дисплей как я понял вещь бесполезная). Есть ли у кого такая прошивка? И работает ли эта контролька со всеми перечисленными китайцами моделями асиков?

[dimmm]

01.02.2020 в 17:55, megabits сказал:

Есть ли у кого такая прошивка?

Есть.Со всеми не проверял НО с S9k ,S9,T9 работает.

[kias]

01.02.2020 в 17:55, megabits сказал:

Видел у китайцев универсальный (S9 T9 S11 S15 T15 S17 T17) тестер хешплат. Контролька там вроде CTRL_C44  ver v1.3010, я так понимаю нужен только UART шнур и прошивка  к на контрольку (дисплей как я понял вещь бесполезная). Есть ли у кого такая прошивка? И работает ли эта контролька со всеми перечисленными китайцами моделями асиков?

Сам пользуюсь такой, работает но под каждую плату, нужна своя прошивка.  

Изменено 3 фев 2020, 06:29 пользователем kias

[xtcjv]

21.12.2019 в 07:30, Splinter сказал:

@xtcjv Рад что помогло. Похоже что на флэше есть бэды или не стабильно читающиеся блоки. Обычно полная прошивка помогает. Но часто плата опять слетает с катушек через некоторое время. Хорошая новость, что повторная прошивка также помогает. Если асик легко доступен и прошивка не является проблемой то с этим можно жить. 

В общем только доделал ремонт, после прошивки, Асик заработал, но одна плата оказалась не рабочей, и в логах было Чайн Хаз 0 Асик.

Сделал все необходимые замеры, и выявил что питание на Чипы вообще не идет (от сюда и 0 асиков). Стал проверять ключи и обвязки по питанию. Понял что управление с Пик Контролера не приходит. (Судя по изначальной поломке, и логе в котором было указана проблема с Пик контроллером, решил все таки попробовать его прошить, для этого заказал программатор ПиКит с Китая)

 

Параллельно проверил как идет сигнал с Пика на рабочей плате, и Имитируя работу как на рабочей плате, на неисправной подал минус на выход Пик контроллера на неисправной плате, в те моменты когда появляется сигнал на исправной. В итоге Плата увидела все асики и даже начала майнить ).

 

Пришел недавно Программатор, прошил по этому ролику https://www.youtube.com/watch?v=yf1LrDgIfAU, скачал дамп с рабочей и залил на неисправную, в Итоге плата полноценно заработала.  

 

Спасибо Splinter, за помощь в ремонте и всему этому форуму.

Изменено 6 фев 2020, 20:02 пользователем xtcjv

[Gor Hakobyan]

21.01.2020 в 10:34, Splinter сказал:

@Gor Hakobyan запускайте хэшплаты по одной и копируйте лог, от неиспользуемых плат отключайте все разъемы. Полученные 3 лога прикрепите сюда. 

Или, если есть возможность, сразу замените блок питания на заведомо исправный. 

Спасибо, прошил заново и все заработало. видимо у этой мат платы глюки, пока полет нормальный. всем спс!

[tojlst9lk]

Товарищи, отвалилась сначала одна плата, теперь вторая пропала.

Блок питания менял на заведомо исправный, все разъемы перепроверил. 

Видно только 7 плату.

Лог приложил:

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]     Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000291] ps7-ttc #0 at df804000, irq=43
[    0.000588] Console: colour dummy device 80x30
[    0.000618] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040198] pid_max: default: 32768 minimum: 301
[    0.040409] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040427] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042522] CPU: Testing write buffer coherency: ok
[    0.042831] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042887] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043104] L310 cache controller enabled
[    0.043124] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.120989] CPU1: Booted secondary processor
[    0.210220] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210352] Brought up 2 CPUs
[    0.210371] SMP: Total of 2 processors activated.
[    0.210379] CPU: All CPU(s) started in SVC mode.
[    0.211032] devtmpfs: initialized
[    0.213426] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214604] regulator-dummy: no parameters
[    0.221948] NET: Registered protocol family 16
[    0.224222] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226486] cpuidle: using governor ladder
[    0.226499] cpuidle: using governor menu
[    0.233783] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235280] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235293] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235403] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.256887] bio: create slab <bio-0> at 0
[    0.258246] vgaarb: loaded
[    0.258959] SCSI subsystem initialized
[    0.259827] usbcore: registered new interface driver usbfs
[    0.260001] usbcore: registered new interface driver hub
[    0.260248] usbcore: registered new device driver usb
[    0.260779] media: Linux media interface: v0.10
[    0.260936] Linux video capture interface: v2.00
[    0.261399] pps_core: LinuxPPS API ver. 1 registered
[    0.261411] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.261535] PTP clock support registered
[    0.261894] EDAC MC: Ver: 3.0.0
[    0.262930] Advanced Linux Sound Architecture Driver Initialized.
[    0.265640] DMA-API: preallocated 4096 debug entries
[    0.265654] DMA-API: debugging enabled by kernel config
[    0.265720] Switched to clocksource arm_global_timer
[    0.286850] NET: Registered protocol family 2
[    0.287501] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.287557] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.287642] TCP: Hash tables configured (established 4096 bind 4096)
[    0.287686] TCP: reno registered
[    0.287703] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.287732] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.287960] NET: Registered protocol family 1
[    0.288284] RPC: Registered named UNIX socket transport module.
[    0.288295] RPC: Registered udp transport module.
[    0.288304] RPC: Registered tcp transport module.
[    0.288312] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288324] PCI: CLS 0 bytes, default 64
[    0.288750] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.290712] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292744] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.292930] msgmni has been set to 967
[    0.293693] io scheduler noop registered
[    0.293706] io scheduler deadline registered
[    0.293746] io scheduler cfq registered (default)
[    0.306012] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.306032] dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.428477] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.995731] console [ttyPS0] enabled
[    0.999970] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.007569] [drm] Initialized drm 1.1.0 20060810
[    1.024482] brd: module loaded
[    1.033825] loop: module loaded
[    1.043212] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.049179] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.057316] libphy: XEMACPS mii bus: probed
[    1.061683] ------------- phy_id = 0x3625e62
[    1.066451] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.075014] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.081664] ehci-pci: EHCI PCI platform driver
[    1.088891] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.095683] usbcore: registered new interface driver usb-storage
[    1.102540] mousedev: PS/2 mouse device common for all mice
[    1.108695] i2c /dev entries driver
[    1.115515] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.121029] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.127018] Xilinx Zynq CpuIdle Driver started
[    1.131853] sdhci: Secure Digital Host Controller Interface driver
[    1.138050] sdhci: Copyright(c) Pierre Ossman
[    1.142319] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.149135] mmc0: no vqmmc regulator found
[    1.153147] mmc0: no vmmc regulator found
[    1.195743] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.204421] usbcore: registered new interface driver usbhid
[    1.209928] usbhid: USB HID core driver
[    1.214625] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.220918] nand: Micron MT29F2G08ABAEAWP
[    1.224886] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.230824] Bad block table found at page 131008, version 0x01
[    1.237044] Bad block table found at page 130944, version 0x01
[    1.243098] 3 ofpart partitions found on MTD device pl353-nand
[    1.248875] Creating 3 MTD partitions on "pl353-nand":
[    1.253968] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.262018] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.269318] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.278198] TCP: cubic registered
[    1.281428] NET: Registered protocol family 17
[    1.286135] Registering SWP/SWPB emulation handler
[    1.292010] regulator-dummy: disabling
[    1.296320] UBI: attaching mtd1 to ubi0
[    1.821986] UBI: scanning is finished
[    1.833562] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.840646] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.847409] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.854073] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.860952] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.866931] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.874038] UBI: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1847073604
[    1.883168] UBI: available PEBs: 26, total reserved PEBs: 1126, PEBs reserved for bad PEB handling: 40
[    1.892470] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.892475] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.896370] ALSA device list:
[    1.896373]   No soundcards found.
[    1.912754] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.941840] UBIFS: recovery needed
[    2.034617] UBIFS: recovery completed
[    2.038301] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.044221] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.053385] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.063242] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.068280] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 275AFE31-7141-4303-9C1B-C61F86AB50DD, small LPT model
[    2.079557] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.086286] devtmpfs: mounted
[    2.089395] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.926616] random: dd urandom read with 0 bits of entropy available
[    3.315765] 
[    3.315765] bcm54xx_config_init
[    3.925764] 
[    3.925764] bcm54xx_config_init
[    7.926586] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    7.932692] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   22.898836] In axi fpga driver!
[   22.901900] request_mem_region OK!
[   22.905290] AXI fpga dev virtual address is 0xdf9fc000
[   22.910429] *base_vir_addr = 0xc51a
[   22.924688] In fpga mem driver!
[   22.928110] request_mem_region OK!
[   22.931618] fpga mem virtual address is 0xe2000000
[   23.715771] 
[   23.715771] bcm54xx_config_init
[   24.335739] 
[   24.335739] bcm54xx_config_init
[   28.336589] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   28.342696] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[  145.150692] random: nonblocking pool is initialized
Detect 512MB control board of XILINX
Miner Type = S9
Fan[0] too slow ...
Fan[0] too slow ...
Fan[0] too slow ...
Fan[0] too slow ...
Fan[0] too slow ...
Fan[0] too slow ...
Fan[0] too slow ...
Fan[0] too slow ...
Fan[0] too slow ...
Fan[0] too slow ...
Fan[4] speed is 5520
Fan[0] too slow ...
Fan[4] speed is 5520
Fan[5] speed is 5160
Fan[4] speed is 5520
Fan[5] speed is 5160
Fan[5] too slow ...
Fan[4] speed is 5520
Fan[5] speed is 5160
Fan[4] speed is 5520
Fan[5] speed is 5160
Fan[4] OK.. Speed is 5520
Fan[5] OK.. Speed is 5160
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Chain[5] secure status [OK]
Chain[6] secure status [OK]
Chain[7] secure status [OK]
Check chain[5] PIC fw version=0x00
chain[5] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
After restore: chain[5] PIC fw version=0x00
chain[5] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
After restore: chain[5] PIC fw version=0x00
Check chain[6] PIC fw version=0x00
chain[6] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
After restore: chain[6] PIC fw version=0x00
chain[6] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[6]
After restore: chain[6] PIC fw version=0x00
Check chain[7] PIC fw version=0x03
Fix freq=750 Chain[5] voltage_pic=74 value=900
Set voltage=860 on chain=6
Fix freq=750 Chain[6] voltage_pic=142 value=860
Fix freq=750 Chain[7] voltage_pic=74 value=900
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
Chain[J8] has 63 asic
Chain[J8] has no freq in PIC, set default freq=750M
Chain[J8] has no core num in PIC

Set PCB PowerOff Temp=90C

Miner fix freq ...
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Asic[ 0]:800 
Asic[ 1]:875 Asic[ 2]:875 Asic[ 3]:875 Asic[ 4]:875 Asic[ 5]:693 Asic[ 6]:875 Asic[ 7]:850 Asic[ 8]:743 
Asic[ 9]:743 Asic[10]:875 Asic[11]:768 Asic[12]:875 Asic[13]:737 Asic[14]:775 Asic[15]:875 Asic[16]:706 
Asic[17]:825 Asic[18]:875 Asic[19]:875 Asic[20]:718 Asic[21]:787 Asic[22]:875 Asic[23]:825 Asic[24]:875 
Asic[25]:850 Asic[26]:781 Asic[27]:875 Asic[28]:875 Asic[29]:781 Asic[30]:875 Asic[31]:875 Asic[32]:612 
Asic[33]:850 Asic[34]:875 Asic[35]:825 Asic[36]:875 Asic[37]:825 Asic[38]:850 Asic[39]:875 Asic[40]:825 
Asic[41]:875 Asic[42]:875 Asic[43]:681 Asic[44]:875 Asic[45]:875 Asic[46]:850 Asic[47]:825 Asic[48]:700 
Asic[49]:875 Asic[50]:875 Asic[51]:850 Asic[52]:781 Asic[53]:875 Asic[54]:875 Asic[55]:875 Asic[56]:825 
Asic[57]:875 Asic[58]:875 Asic[59]:693 Asic[60]:825 Asic[61]:875 Asic[62]:768 
Chain:7 max freq=875
Chain:7 min freq=612

max freq = 875
set baud=0
Chain[7] PIC temp offset=62,-5,0,0,0,0,33,0
chain[7] temp chip I2C addr=0x98
New offset Chain[7] chip[244] local:19 remote:21 offset:28 
Chain[7] chip[244] get middle temp offset=28 typeID=55
Chain[J8] set working voltage=900 [74]
setStartTimePoint total_tv_start_sys=490 total_tv_end_sys=491
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=87.1240 Asic[02]=92.3410 Asic[03]=96.3340 Asic[04]=90.8310 Asic[05]=97.9620 Asic[06]=79.2050 Asic[07]=100.730 Asic[08]=91.4860 
Asic[09]=89.3720 Asic[10]=81.7380 Asic[11]=98.4480 Asic[12]=82.6940 Asic[13]=98.5150 Asic[14]=85.2610 Asic[15]=90.3280 Asic[16]=97.8440 
Asic[17]=79.5740 Asic[18]=91.7880 Asic[19]=106.937 Asic[20]=99.8570 Asic[21]=84.0200 Asic[22]=88.3480 Asic[23]=91.3850 Asic[24]=87.1740 
Asic[25]=96.4180 Asic[26]=92.9280 Asic[27]=94.9420 Asic[28]=102.592 Asic[29]=100.378 Asic[30]=92.8280 Asic[31]=99.0520 Asic[32]=101.502 
Asic[33]=50.2640 Asic[34]=97.7600 Asic[35]=96.6530 Asic[36]=95.2610 Asic[37]=93.6830 Asic[38]=94.2710 Asic[39]=99.1190 Asic[40]=104.136 
Asic[41]=93.9520 Asic[42]=101.183 Asic[43]=96.7870 Asic[44]=82.5600 Asic[45]=106.753 Asic[46]=101.854 Asic[47]=97.5760 Asic[48]=91.7710 
Asic[49]=80.5300 Asic[50]=98.7670 Asic[51]=96.2340 Asic[52]=96.4680 Asic[53]=84.5230 Asic[54]=101.535 Asic[55]=96.0320 Asic[56]=97.5930 
Asic[57]=97.8780 Asic[58]=103.498 Asic[59]=90.6130 Asic[60]=79.3220 Asic[61]=94.6060 Asic[62]=105.511 Asic[63]=88.9360 
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Asic[07]=100.730000
Asic[19]=106.937000
Asic[28]=102.592000
Asic[29]=100.378000
Asic[32]=101.502000
Asic[40]=104.136000
Asic[42]=101.183000
Asic[45]=106.753000
Asic[46]=101.854000
Asic[54]=101.535000
Asic[58]=103.498000
Asic[62]=105.511000
Done check_asic_reg
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=28
Chain[7] Chip[62] local Temp=60
Chain[7] Chip[62] middle Temp=72
Done read temp on Chain[7]
set FAN speed according to: temp_highest=72 temp_top1[PWM_T]=72 temp_top1[TEMP_POS_LOCAL]=60 temp_change=-2 fix_fan_steps=0
set normal FAN speed...with fix_fan_steps=0
FAN PWM: 64
read_temp_func Done!
CRC error counter=0
 

 

Изменено 9 фев 2020, 21:18 пользователем tojlst9lk

[Splinter]

@tojlst9lk На 2-х платах слетели прошивки PIC (микроконтроллеры на хэшплатах отвечающие за питание). Нужен программатор PicKit3 если планируете самостоятельно решать проблему. Или несите их в сервис. Адекватный сервис за это дорого не возьмет.

[tojlst9lk]

7 часов назад, Splinter сказал:

@tojlst9lk На 2-х платах слетели прошивки PIC (микроконтроллеры на хэшплатах отвечающие за питание). Нужен программатор PicKit3 если планируете самостоятельно решать проблему. Или несите их в сервис. Адекватный сервис за это дорого не возьмет.

Спасибо. я достаточно далеко живу и пересыл встанет от 1000 за 3 платы (есть еще один асик с9и с такими же признаками) в одну сторону, лучше сам попробую. Т.е. нужен программатор, живая плата и немного гугла. 

Где взять ПО при помощи которого нужно прошивать?

Из-за чего такое происходит?

Не посоветуете проверенные ссылки с али?

[Splinter]

10 часов назад, tojlst9lk сказал:

Где взять ПО при помощи которого нужно прошивать?

Родное ПО от Microchip называется MPLAB X IPE.

10 часов назад, tojlst9lk сказал:

Из-за чего такое происходит?

Точно сложно сказать. Разные причины бывают. В контрольке есть механизм обновления прошивки пика если считывается неверная версия зашитой в него программы. Бывает что читается версия 0 и инициируется процесс прошивки. Но на самом деле это проблема где-то в коммуникации, плохой контакт, зависший пик или еще какой глюк. Процесс прошивки начинается криво и затирается часть памяти но ничего путного не записывается. Это одна из причин, возможно могут быть и другие.

10 часов назад, tojlst9lk сказал:

Не посоветуете проверенные ссылки с али?

Думаю ссылку посчитают за рекламу и забанят.  Да и думаю можно брать у любого продавца с нормальной репутацией. Я брал у первого попавшегося, никаких проблем. 

[vovchik]

4 минуты назад, Splinter сказал:

Думаю ссылку посчитают за рекламу и забанят.

Если ссылка не реферальная то можно.