Перейти к содержанию

Ремонт: Bitmain Antminer s7, s9, l3+


Hlorofos
Сообщение добавил Hlorofos

Все полезные ссылки и FAQ можно найти в первом сообщении. Прежде чем задать вопрос, посмотрите там.

Рекомендуемые сообщения

Здравствуйте, подскажите пожалуйста, на чипах bm1387b нанесена точка это означает что второй контакт? Как бы намекая верно установить? И еще кто шарит посмотрите фото первый раз менял чип правильно ли установлен по контактам?

20190821_001531.jpg

Изменено пользователем maxi686
Дополнил вопрос
Ссылка на комментарий
Поделиться на другие сайты

всем добрый вечер есть тестер для s9 скопировал флэшку с него. как нужно поставить джамперы на контрольке от S9 чтоб она загружалась с флэшки

заранее спасибо

 

Ссылка на комментарий
Поделиться на другие сайты

Ссылка на комментарий
Поделиться на другие сайты

что серьезно замкнуть микросхему памяти

 

то что там описано, описано для перепрошивки контрольки. мне нужно чтоб контролька запустилась с флэш карты и смогла работать как тэстер это возможно?

 

Ссылка на комментарий
Поделиться на другие сайты

2 минуты назад, dimmos747 сказал:

что серьезно замкнуть микросхему памяти

 

джампер переставь jp4

Ссылка на комментарий
Поделиться на другие сайты

2 часа назад, dimmos747 сказал:

то что там описано, описано для перепрошивки контрольки. мне нужно чтоб контролька запустилась с флэш карты и смогла работать как тэстер это возможно?

Я так полагаю вы пытаетесь контрольку на Xilinx заставить работать как тестер? Это невозможно, тестер собран на контрольке с Cyclon5 (старая версия контрольки для S9).

Ссылка на комментарий
Поделиться на другие сайты

22.08.2019 в 23:16, Splinter сказал:

Я так полагаю вы пытаетесь контрольку на Xilinx заставить работать как тестер? Это невозможно, тестер собран на контрольке с Cyclon5 (старая версия контрольки для S9).

спасибо понял. буду делать на основе контрольки от z9 mini

вроде должна подойти

 

 

25.02.2019 в 12:42, alexey7mechanic сказал:

Напишите почту, я скину.

Скиньте и мне если можно объяснить пожалуйста. Student.29ospn@mail.ru 

 

 

30.04.2018 в 21:05, Splinter сказал:

Как знают все ремонтники, плавающий дефект самый поганый. Строгой диагностики поддаются только стабильные неисправности. Вот и в вашем случае точных советов вряд ли можно дать. Скажу только из личного опыта. ASIC[x], где  x число якобы работающих чипов, совсем не означает, что неисправен x+1 чип, а только значит что любой за x. Мрут чипы чаще всего на границе доменов. Много холодной пайки. Чипы ревизии "B" мрут чаще. У чипов часто отрывает ноги.

Многие из этих дефектов ведут к нестабильному проявлению неисправности, в основном с прогревом, повышением частоты или повышением напряжения. Первые два в основном связанны с контактом. А вот последний более хитрый. Вся проблема в совершенно не логичной китайской схемотехнике. Из нее вытекают перекосы питания доменов и обрывы в прохождении сигнала опроса через всю цепочку чипов. Дело в том, что сигнал на границе доменов приходит или возвращается в чип с уровнем 1,8 В, но относительно уровня земли соседнего домена. Соответственно к нему нужно прибавить или вычесть напряжение питания домена. И если с уровнем RI в 2.2-2.3 вольта чипы вроде справляются, то вот занижение уровня до 1,3 В  особенно на RST не все чипы воспринимают и уходят в глухую несознанку. Замечено, что чипы без ревизии "B" легче это переносят.

Чтобы понимать что происходит в схеме, нужно четко представлять себе как работает интерфейс чипов и как они обмениваются в цепочке. По суте это обычный UART. Но есть несколько особенностей. 

1. Все сигналы проходят последовательно через чипы и если один чип хандрит, то пропадают все чипы за ним, а если он в добавок ложит линию RI в ноль, то встает вся цепочка (да, тот самый ASIC[0]).

2. Чипы на линии адресуются программно, но после сброса они все имеют адрес 0 и для того чтобы они все хором не отвечали в линию до того как им будет присвоены уникальные адреса, применяется сигнал BO (busy output), высокий уровень которого запрещает чипам отвечать, т.о. если BO после неисправного чипа высокий, то все чипы за ним покорно молчат, ожидая освобождение линии.

3. Активный уровень сигнала RST низкий, т.е. при нем все чипы находятся в состоянии сброс.. Чтобы чип работал RST должен быть высоким. На границе доменов его уровень падает до 1.3-1.4 В, что некоторые чипы иногда воспринимают как сброс, видимо это на границе уровня переключения. 

4. Ну и CO и RI это обычные RX и TX, активный уровень низкий, при отсутствии обмена пассивный уровень высокий. То что вошло на CO 1-го чипа сквозняком дойдет до последнего. И соответственно, какая бы фигня не появилась на выходе RI последнего чипа, она дойдет до первого и уйдет в контрольку.  (CO и RI  даны относительно контрольных точек, на чипах это соответственно CI и RO).

Т.о. берите вольтметр и осциллограф в руки и смотрите сигналы вокруг 3-го и 4-го чипов (как правило хватает вольтметра). Если как вы говорит перезагрузка помогает то крутитесь вокруг уровня сигнала RST.

 

P.S. Возможно вы все это итак знали, просто выдалось свободное время и решил написать, может кому еще будет интересно, схемотехника нетривиальная, потому многие чинят тыкаясь наобум. Да и улыбает, как некоторые здесь утверждают, что без ASIC-тестера ну прям никуда. Шнурок от сотового (преобразователь USB - UART) и пара строчек в терминалке дают пользы неменьше ( да неудобно, зато бесплатно ? )

Спасибо полное обьяснение. Подскажите как запустить контрольку в циклический опрос чипов? 

 

Ссылка на комментарий
Поделиться на другие сайты

5 часов назад, dimmos747 сказал:

Спасибо полное обьяснение. Подскажите как запустить контрольку в циклический опрос чипов? 

 

Пожалуйста. Зацикленный bmminer выкладывал в этой теме alexey7mechanic

Ссылка на комментарий
Поделиться на другие сайты

Подскажите пожалуйста кто знает, чем отличается подложка у чипов bm1387b есть золотистая и есть серая какая то

Ссылка на комментарий
Поделиться на другие сайты

24.08.2019 в 22:24, Splinter сказал:

Пожалуйста. Зацикленный bmminer выкладывал в этой теме alexey7mechanic

посмотрел что то не нашел((

 

Ссылка на комментарий
Поделиться на другие сайты

Ссылка на комментарий
Поделиться на другие сайты

5 часов назад, dizil сказал:

спасибо теперь хоть с тестированием проблем меньше

 

Ссылка на комментарий
Поделиться на другие сайты

Здравствуйте.

Проблема с Antminer D3

 

Похоже, проблема с платой управления.

Подскажите, в чём может быть проблема. Лог прилагаю.

 

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 65280
[    0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 64768 pages, LIFO batch:15
[    0.000000] AM335X ES1.0 (neon )
[    0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768
[    0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
[    0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 255MB = 255MB total
[    0.000000] Memory: 238672k/238672k available, 23472k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0612cf0   (6188 kB)
[    0.000000]       .init : 0xc0613000 - 0xc06554c0   ( 266 kB)
[    0.000000]       .data : 0xc0656000 - 0xc06cc020   ( 473 kB)
[    0.000000]        .bss : 0xc06cc020 - 0xc0725e3c   ( 360 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000354] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[    0.015437] pid_max: default: 32768 minimum: 301
[    0.015669] Security Framework initialized
[    0.015764] Mount-cache hash table entries: 512
[    0.024592] Initializing cgroup subsys cpuacct
[    0.024627] Initializing cgroup subsys memory
[    0.024689] Initializing cgroup subsys blkio
[    0.024824] CPU: Testing write buffer coherency: ok
[    0.025391] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.025467] Setting up static identity map for 0x8038c820 - 0x8038c86c
[    0.026793] Brought up 1 CPUs
[    0.026817] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[    0.028113] devtmpfs: initialized
[    0.092521] pinctrl core: initialized pinctrl subsystem
[    0.092737] rstctl core: initialized rstctl subsystem
[    0.093231] regulator-dummy: no parameters
[    0.093803] NET: Registered protocol family 16
[    0.094507] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.104181] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
[    0.104363] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.105449] platform 49000000.edma: alias fck already exists
[    0.105484] platform 49000000.edma: alias fck already exists
[    0.105512] platform 49000000.edma: alias fck already exists
[    0.106659] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.106840] OMAP GPIO hardware version 0.1
[    0.108242] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.109566] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.110889] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.111515] of_get_named_gpio_flags exited with status 52
[    0.111547] gpio-rctrl rstctl.3: loaded OK
[    0.116651] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.119859] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.122045] cpsw.0: No hwaddr in dt. Using 94:e3:6d:f7:8e:fd from efuse
[    0.122077] cpsw.1: No hwaddr in dt. Using 94:e3:6d:f7:8e:ff from efuse
[    0.137629] bio: create slab <bio-0> at 0
[    0.149770] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[    0.150012] of_get_named_gpio_flags: can't parse gpios property
[    0.150302] vmmcsd_fixed: 3300 mV 
[    0.153429] SCSI subsystem initialized
[    0.153881] usbcore: registered new interface driver usbfs
[    0.153996] usbcore: registered new interface driver hub
[    0.154336] usbcore: registered new device driver usb
[    0.156442] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
[    0.156476] omap_i2c 4819c000.i2c: unable to select pin group
[    0.156671] media: Linux media interface: v0.10
[    0.156768] Linux video capture interface: v2.00
[    0.156887] pps_core: LinuxPPS API ver. 1 registered
[    0.156903] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.157625] Advanced Linux Sound Architecture Driver Initialized.
[    0.158820] Switching to clocksource gp_timer
[    0.176847] NET: Registered protocol family 2
[    0.177840] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.177930] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[    0.178020] TCP: Hash tables configured (established 2048 bind 2048)
[    0.178111] TCP: reno registered
[    0.178137] UDP hash table entries: 256 (order: 1, 12288 bytes)
[    0.178182] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[    0.178682] NET: Registered protocol family 1
[    0.179272] RPC: Registered named UNIX socket transport module.
[    0.179292] RPC: Registered udp transport module.
[    0.179306] RPC: Registered tcp transport module.
[    0.179320] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.179710] Trying to unpack rootfs image as initramfs...
[    1.945132] Freeing initrd memory: 12244K
[    1.945817] CPU PMU: probing PMU on CPU 0
[    1.945851] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[    1.946466] omap2_mbox_probe: platform not supported
[    1.950330] VFS: Disk quotas dquot_6.5.2
[    1.950568] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.951949] NFS: Registering the id_resolver key type
[    1.952055] Key type id_resolver registered
[    1.952072] Key type id_legacy registered
[    1.952140] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.952581] msgmni has been set to 490
[    1.955378] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.955405] io scheduler noop registered
[    1.955421] io scheduler deadline registered
[    1.955479] io scheduler cfq registered (default)
[    1.959398] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.961980] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[    1.962269] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[    2.623082] console [ttyO0] enabled
[    2.627618] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
[    2.636318] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
[    2.644958] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
[    2.653618] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
[    2.662598] [drm] Initialized drm 1.1.0 20060810
[    2.681258] brd: module loaded
[    2.691505] loop: module loaded
[    2.695681] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
[    2.705611] nand_get_flash_type: 2c,f1 against 2c,f1
[    2.711144] ONFI param page 0 valid
[    2.714818] ONFI flash detected
[    2.718138] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABAEAWP), 128MiB, page size: 2048, OOB size: 64
[    2.730050] omap2-nand: detected x8 NAND flash
[    2.734716] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    2.740299] omap2-nand: using custom ecc layout
[    2.745142] 10 ofpart partitions found on MTD device omap2-nand.0
[    2.751536] Creating 10 MTD partitions on "omap2-nand.0":
[    2.757213] 0x000000000000-0x000000020000 : "spl"
[    2.764017] 0x000000020000-0x000000040000 : "spl_backup1"
[    2.771471] 0x000000040000-0x000000060000 : "spl_backup2"
[    2.778888] 0x000000060000-0x000000080000 : "spl_backup3"
[    2.786287] 0x000000080000-0x000000240000 : "u-boot"
[    2.794548] 0x000000240000-0x000000260000 : "bootenv"
[    2.801447] 0x000000260000-0x000000280000 : "fdt"
[    2.808088] 0x000000280000-0x000000780000 : "kernel"
[    2.819035] 0x000000800000-0x000001c00000 : "root"
[    2.842525] 0x000001c00000-0x000003000000 : "config"
[    2.866310] OneNAND driver initializing
[    2.872058] usbcore: registered new interface driver asix
[    2.877870] usbcore: registered new interface driver cdc_ether
[    2.884119] usbcore: registered new interface driver smsc95xx
[    2.890240] usbcore: registered new interface driver net1080
[    2.896266] usbcore: registered new interface driver cdc_subset
[    2.902560] usbcore: registered new interface driver zaurus
[    2.908567] usbcore: registered new interface driver cdc_ncm
[    2.915327] usbcore: registered new interface driver cdc_acm
[    2.921283] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.929662] Initializing USB Mass Storage driver...
[    2.934903] usbcore: registered new interface driver usb-storage
[    2.941203] USB Mass Storage support registered.
[    2.946243] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    2.952949] musb-hdrc musb-hdrc.0.auto: pdev->id = 0
[    2.958196] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.966967] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.966989] musb-hdrc: MHDRC RTL version 2.0 
[    2.967004] musb-hdrc: setup fifo_mode 4
[    2.967031] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.967180] musb-hdrc musb-hdrc.0.auto: *** mode=3
[    2.972225] musb-hdrc musb-hdrc.0.auto: *** power=250
[    2.978241] musb-hdrc musb-hdrc.1.auto: pdev->id = 1
[    2.983493] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.992262] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.992283] musb-hdrc: MHDRC RTL version 2.0 
[    2.992297] musb-hdrc: setup fifo_mode 4
[    2.992319] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.992459] musb-hdrc musb-hdrc.1.auto: *** mode=1
[    2.997503] musb-hdrc musb-hdrc.1.auto: *** power=250
[    3.002835] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    3.009481] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
[    3.017741] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup
[    3.017845] usb usb1: default language 0x0409
[    3.017902] usb usb1: udev 1, busnum 1, minor = 0
[    3.017926] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.025056] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.032627] usb usb1: Product: MUSB HDRC host driver
[    3.037843] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd
[    3.043509] usb usb1: SerialNumber: musb-hdrc.1.auto
[    3.049474] usb usb1: usb_probe_device
[    3.049501] usb usb1: configuration #1 chosen from 1 choice
[    3.049611] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    3.049817] hub 1-0:1.0: usb_probe_interface
[    3.049839] hub 1-0:1.0: usb_probe_interface - got id
[    3.049866] hub 1-0:1.0: USB hub found
[    3.053858] hub 1-0:1.0: 1 port detected
[    3.057997] hub 1-0:1.0: standalone hub
[    3.058017] hub 1-0:1.0: individual port power switching
[    3.058035] hub 1-0:1.0: no over-current protection
[    3.058053] hub 1-0:1.0: Single TT
[    3.058074] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    3.058094] hub 1-0:1.0: power on to power good time: 10ms
[    3.058151] hub 1-0:1.0: local power source is good
[    3.058267] hub 1-0:1.0: enabling power on all ports
[    3.059356] mousedev: PS/2 mouse device common for all mice
[    3.067274] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[    3.075065] i2c /dev entries driver
[    3.080083] pps_ldisc: PPS line discipline registered
[    3.085569] Driver for 1-wire Dallas network protocol.
[    3.092887] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    3.100485] cpuidle: using governor ladder
[    3.104809] cpuidle: using governor menu
[    3.109368] of_get_named_gpio_flags exited with status 6
[    3.109387] of_get_named_gpio_flags: can't parse gpios property
[    3.109403] of_get_named_gpio_flags: can't parse gpios property
[    3.109440] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[    3.116678] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[    3.123492] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[    3.130715] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[    3.138053] mmc.4 supply vmmc_aux not found, using dummy regulator
[    3.144998] omap_hsmmc mmc.4: pins are not configured from the driver
[    3.159024] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[    3.179055] of_get_named_gpio_flags exited with status -517
[    3.179122] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.186906] ledtrig-cpu: registered to indicate activity on CPUs
[    3.193678] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[    3.200877] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[    3.208984] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[    3.215333] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[    3.222519] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[    3.234780] usbcore: registered new interface driver usbhid
[    3.240697] usbhid: USB HID core driver
[    3.247579] TCP: cubic registered
[    3.251102] Initializing XFRM netlink socket
[    3.255671] NET: Registered protocol family 17
[    3.260548] NET: Registered protocol family 15
[    3.265418] Key type dns_resolver registered
[    3.270057] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    3.278137] ThumbEE CPU extension supported.
[    3.282646] Registering SWP/SWPB emulation handler
[    3.288660] registered taskstats version 1
[    3.295275] of_get_named_gpio_flags exited with status -517
[    3.295347] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.352334] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[    3.358745] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[    3.373294] libphy: 4a101000.mdio: probed
[    3.377615] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[    3.387856] Detected MACID = 94:e3:6d:f7:8e:fd
[    3.392536] cpsw 4a100000.ethernet: NAPI disabled
[    3.397924] of_get_named_gpio_flags exited with status -517
[    3.397988] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.406704] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    3.415986] cpu0 supply cpu0 not found, using dummy regulator
[    3.422493] cpufreq_cpu0: failed to scale voltage up: -22
[    3.428312] cpufreq_cpu0: failed to scale voltage up: -22
[    3.441101] ALSA device list:
[    3.444339]   No soundcards found.
[    3.448903] Freeing init memory: 264K
[    3.452951] Failed to execute /init
[    4.447518] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    5.772932] net eth0: initializing cpsw version 1.12 (0)
[    5.781883] net eth0: phy found : id is : 0x7c0f1
[    5.787313] libphy: PHY 4a101000.mdio:01 not found
[    5.792513] net eth0: phy 4a101000.mdio:01 not found on slave 1
[    9.927066] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
Aug 27 13:30:58 (none) local0.err cgminer: Miner compile time: Tue Nov 13 11:46:56 CST 2018 type: Antminer D3
Aug 27 13:30:58 (none) local0.warn cgminer: Started cgminer 4.9.0
Aug 27 13:30:58 (none) local0.warn cgminer[362]: bitmain_DASH_init
Aug 27 13:30:59 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:30:59 (none) local0.err cgminer[362]: FAN2 too slow ...
Aug 27 13:30:59 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:30:59 (none) local0.err cgminer[362]: FAN2 too slow ...
Aug 27 13:31:00 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:00 (none) local0.err cgminer[362]: FAN2 too slow ...
Aug 27 13:31:00 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:01 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:01 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:02 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:02 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:03 (none) local0.warn cgminer[362]: check_fan_speed OK
Aug 27 13:31:03 (none) local0.notice cgminer[362]: detected at /sys/class/gpio/gpio51/value  chain 0
Aug 27 13:31:03 (none) local0.notice cgminer[362]: detected at /sys/class/gpio/gpio48/value  chain 1
Aug 27 13:31:03 (none) local0.notice cgminer[362]: detected at /sys/class/gpio/gpio47/value  chain 2
Aug 27 13:31:03 (none) local0.notice cgminer[362]: detect total chain num 3
Aug 27 13:31:03 (none) local0.notice cgminer[362]: i2c init ok
Aug 27 13:31:03 (none) local0.notice cgminer[362]: check_whether_need_update_pic_program
Aug 27 13:31:04 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:04 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:05 (none) local0.notice cgminer[362]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 27 13:31:06 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:06 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:07 (none) local0.notice cgminer[362]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 27 13:31:08 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:08 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:09 (none) local0.notice cgminer[362]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 27 13:31:09 (none) local0.notice cgminer[362]: every_chain_reset_PIC16F1704_pic_new
Aug 27 13:31:10 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:11 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:12 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:13 (none) local0.notice cgminer[362]: every_chain_jump_from_loader_to_app_PIC16F1704_new
Aug 27 13:31:13 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:14 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:14 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:15 (none) local0.notice cgminer[362]: reset_hash_board_low 0
Aug 27 13:31:15 (none) local0.notice cgminer[362]: pic_heart_beat_func_new
Aug 27 13:31:15 (none) local0.notice cgminer[362]: reset_hash_board_low 1
Aug 27 13:31:15 (none) local0.notice cgminer[362]: reset_hash_board_low 2
Aug 27 13:31:15 (none) local0.notice cgminer[362]: reset_hash_board_low 3
Aug 27 13:31:15 (none) local0.notice cgminer[362]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 27 13:31:15 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:16 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:16 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:16 (none) local0.notice cgminer[362]: reset_hash_board_high 0
Aug 27 13:31:16 (none) local0.notice cgminer[362]: reset_hash_board_high 1
Aug 27 13:31:16 (none) local0.notice cgminer[362]: reset_hash_board_high 2
Aug 27 13:31:16 (none) local0.notice cgminer[362]: reset_hash_board_high 3
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain chainid = 0
Aug 27 13:31:17 (none) local0.err cgminer[362]: create rx read thread for chain 0 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: Start A New Asic Response.Chain Id:[0]
Aug 27 13:31:17 (none) local0.err cgminer[362]: create tx read thread for chain 0 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: open device over
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain chainid = 1
Aug 27 13:31:17 (none) local0.err cgminer[362]: create rx read thread for chain 1 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: Start A New Asic Response.Chain Id:[1]
Aug 27 13:31:17 (none) local0.err cgminer[362]: create tx read thread for chain 1 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: open device over
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain chainid = 2
Aug 27 13:31:17 (none) local0.err cgminer[362]: create rx read thread for chain 2 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: Start A New Asic Response.Chain Id:[2]
Aug 27 13:31:17 (none) local0.err cgminer[362]: create tx read thread for chain 2 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: open device over
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain
Aug 27 13:31:17 (none) local0.notice cgminer[362]: open device over
Aug 27 13:31:18 (none) local0.notice cgminer[362]: check_every_chain_asic_number
Aug 27 13:31:18 (none) local0.warn cgminer[362]: check_asic_reg: Chain0 has 0 ASICs
Aug 27 13:31:18 (none) local0.warn cgminer[362]: check_asic_reg: Chain1 has 54 ASICs
Aug 27 13:31:18 (none) local0.warn cgminer[362]: check_asic_reg: Chain2 has 0 ASICs
Aug 27 13:31:19 (none) local0.notice cgminer[362]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 27 13:31:20 (none) local0.notice cgminer[362]: reset_hash_board_low 0
Aug 27 13:31:20 (none) local0.notice cgminer[362]: reset_hash_board_low 1
Aug 27 13:31:20 (none) local0.notice cgminer[362]: reset_hash_board_low 2
Aug 27 13:31:20 (none) local0.notice cgminer[362]: reset_hash_board_low 3
Aug 27 13:31:21 (none) local0.notice cgminer[362]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 27 13:31:21 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:21 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:21 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:22 (none) local0.notice cgminer[362]: reset_hash_board_high 0
Aug 27 13:31:22 (none) local0.notice cgminer[362]: reset_hash_board_high 1
Aug 27 13:31:22 (none) local0.notice cgminer[362]: reset_hash_board_high 2
Aug 27 13:31:22 (none) local0.notice cgminer[362]: reset_hash_board_high 3
Aug 27 13:31:22 (none) local0.notice cgminer[362]: check_every_chain_asic_number
Aug 27 13:31:22 (none) local0.warn cgminer[362]: check_asic_reg: Chain0 has 0 ASICs
Aug 27 13:31:23 (none) local0.warn cgminer[362]: check_asic_reg: Chain1 has 54 ASICs
Aug 27 13:31:23 (none) local0.warn cgminer[362]: check_asic_reg: Chain2 has 0 ASICs
Aug 27 13:31:23 (none) local0.notice cgminer[362]: recheck_asic_num DONE!
Aug 27 13:31:23 (none) local0.notice cgminer[362]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 27 13:31:24 (none) local0.notice cgminer[362]: reset_hash_board_low 0
Aug 27 13:31:24 (none) local0.notice cgminer[362]: reset_hash_board_low 1
Aug 27 13:31:24 (none) local0.notice cgminer[362]: reset_hash_board_low 2
Aug 27 13:31:24 (none) local0.notice cgminer[362]: reset_hash_board_low 3
Aug 27 13:31:25 (none) local0.notice cgminer[362]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 27 13:31:25 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:25 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:26 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:26 (none) local0.notice cgminer[362]: reset_hash_board_high 0
Aug 27 13:31:26 (none) local0.notice cgminer[362]: reset_hash_board_high 1
Aug 27 13:31:26 (none) local0.notice cgminer[362]: reset_hash_board_high 2
Aug 27 13:31:26 (none) local0.notice cgminer[362]: reset_hash_board_high 3
Aug 27 13:31:27 (none) local0.notice cgminer[362]: check_every_chain_asic_number
Aug 27 13:31:27 (none) local0.warn cgminer[362]: check_asic_reg: Chain0 has 0 ASICs
Aug 27 13:31:27 (none) local0.warn cgminer[362]: check_asic_reg: Chain1 has 54 ASICs
Aug 27 13:31:27 (none) local0.warn cgminer[362]: check_asic_reg: Chain2 has 0 ASICs
Aug 27 13:31:28 (none) local0.notice cgminer[362]: recheck_asic_num DONE!
Aug 27 13:31:28 (none) local0.notice cgminer[362]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 27 13:31:28 (none) local0.notice cgminer[362]: reset_hash_board_low 0
Aug 27 13:31:28 (none) local0.notice cgminer[362]: reset_hash_board_low 1
Aug 27 13:31:28 (none) local0.notice cgminer[362]: reset_hash_board_low 2
Aug 27 13:31:28 (none) local0.notice cgminer[362]: reset_hash_board_low 3
Aug 27 13:31:29 (none) local0.notice cgminer[362]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 27 13:31:29 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:30 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:30 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:31 (none) local0.notice cgminer[362]: reset_hash_board_high 0
Aug 27 13:31:31 (none) local0.notice cgminer[362]: reset_hash_board_high 1
Aug 27 13:31:31 (none) local0.notice cgminer[362]: reset_hash_board_high 2
Aug 27 13:31:31 (none) local0.notice cgminer[362]: reset_hash_board_high 3
Aug 27 13:31:31 (none) local0.notice cgminer[362]: check_every_chain_asic_number
Aug 27 13:31:31 (none) local0.warn cgminer[362]: check_asic_reg: Chain0 has 0 ASICs
Aug 27 13:31:31 (none) local0.warn cgminer[362]: check_asic_reg: Chain1 has 54 ASICs
Aug 27 13:31:32 (none) local0.warn cgminer[362]: check_asic_reg: Chain2 has 0 ASICs
Aug 27 13:31:32 (none) local0.notice cgminer[362]: recheck_asic_num DONE!
Aug 27 13:31:32 (none) local0.notice cgminer[362]: calculate_address_interval: temp_asic_number = 64, addrInterval = 1
Aug 27 13:31:32 (none) local0.notice cgminer[362]: calculate_address_interval: CHIP_OFFSET = 0x04000000, CORE_OFFSET = 0x00800000
Aug 27 13:31:32 (none) local0.notice cgminer[362]: set_ticket_mask ticket_mask = 0x0000001b
Aug 27 13:31:32 (none) local0.notice cgminer[362]: every_chain_get_PIC16F1704_freq_new
Aug 27 13:31:34 (none) local0.notice cgminer[362]: set_frequency: frequency = 537
Aug 27 13:31:34 (none) local0.notice cgminer[362]: software_set_address_chain: chain 0 has 0 ASIC, and addrInterval is 1
Aug 27 13:31:34 (none) local0.notice cgminer[362]: Now Set [0] Chain Address
Aug 27 13:31:35 (none) local0.notice cgminer[362]: software_set_address_chain: chain 1 has 54 ASIC, and addrInterval is 1
Aug 27 13:31:35 (none) local0.notice cgminer[362]: Now Set [1] Chain Address
Aug 27 13:31:36 (none) local0.notice cgminer[362]: software_set_address_chain: chain 2 has 0 ASIC, and addrInterval is 1
Aug 27 13:31:36 (none) local0.notice cgminer[362]: Now Set [2] Chain Address
Aug 27 13:31:37 (none) local0.notice cgminer[362]: software_set_address_chain: chain 3 has 0 ASIC, and addrInterval is 1
Aug 27 13:31:37 (none) local0.notice cgminer[362]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 27 13:31:37 (none) local0.notice cgminer[362]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 27 13:31:37 (none) local0.notice cgminer[362]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 27 13:31:37 (none) local0.notice cgminer[362]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: 0 calibration_sensor_offset_chain
Aug 27 13:31:37 (none) local0.notice cgminer[362]: chain:0 local:0 remote:0
Aug 27 13:31:37 (none) local0.warn cgminer[362]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 27 13:31:38 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 27 13:31:38 (none) local0.notice cgminer[362]: 1 calibration_sensor_offset_chain
Aug 27 13:31:39 (none) local0.notice cgminer[362]: chain:1 local:0 remote:0
Aug 27 13:31:39 (none) local0.warn cgminer[362]: Chain 1 set_temperature_offset_value_chain_sensor
Aug 27 13:31:40 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain1 Sensor0 temp offset : 00, 
Aug 27 13:31:40 (none) local0.notice cgminer[362]: 2 calibration_sensor_offset_chain
Aug 27 13:31:40 (none) local0.notice cgminer[362]: chain:2 local:0 remote:0
Aug 27 13:31:40 (none) local0.warn cgminer[362]: Chain 2 set_temperature_offset_value_chain_sensor
Aug 27 13:31:41 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain2 Sensor0 temp offset : 00, 
Aug 27 13:31:41 (none) local0.warn cgminer[362]: Chain 0 set_temperature_offset_value_chain
Aug 27 13:31:41 (none) local0.warn cgminer[362]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 27 13:31:42 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 27 13:31:42 (none) local0.warn cgminer[362]: Chain 1 set_temperature_offset_value_chain
Aug 27 13:31:42 (none) local0.warn cgminer[362]: Chain 1 set_temperature_offset_value_chain_sensor
Aug 27 13:31:42 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain1 Sensor0 temp offset : 00, 
Aug 27 13:31:42 (none) local0.warn cgminer[362]: Chain 2 set_temperature_offset_value_chain
Aug 27 13:31:42 (none) local0.warn cgminer[362]: Chain 2 set_temperature_offset_value_chain_sensor
Aug 27 13:31:43 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain2 Sensor0 temp offset : 00, 
Aug 27 13:31:43 (none) local0.notice cgminer[362]: frequency = '537'
Aug 27 13:31:43 (none) local0.notice cgminer[362]: dev.timeout = 562356 us
Aug 27 13:31:43 (none) local0.notice cgminer[362]: open_core_chain
Aug 27 13:31:43 (none) local0.notice cgminer[362]: open_core_chain
Aug 27 13:31:43 (none) local0.notice cgminer[362]: open_core_chain
Aug 27 13:31:44 (none) local0.notice cgminer[362]: open_core_chain
Aug 27 13:31:47 (none) local0.err cgminer[362]: cgminer time error total_secs = 1566912707.089818 last_total_secs = 1.000000
Aug 27 13:31:47 (none) local0.warn cgminer[362]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 27 13:31:47 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:31:51 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:31:54 (none) local0.warn cgminer[362]: API running in IP access mode on port 4028 (16)
Aug 27 13:31:56 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:00 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:04 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:08 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:12 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:16 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:20 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:25 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:29 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:33 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:37 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:41 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:45 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:50 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:54 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:58 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:33:02 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!

 

Ссылка на комментарий
Поделиться на другие сайты

17.08.2019 в 13:51, Splinter сказал:

@emigrate86 с али много дохлых или залоченых процов. Но я бы на всякий случай снял и перекатал еще раз. 

Перекатал, запустилась. Трафарет подошел от моторолы кнопочной, с тех времен осталось.

Ссылка на комментарий
Поделиться на другие сайты

18.08.2019 в 14:47, Splinter сказал:

@prokat эти 2 крайних пина не задействованы, отваливаются часто. 

Судя по ЭТОМУ изображению, все же куда-то уходят.

Принесли плату, с отвалившимся чипом, на чипе остались пятачки от 17, 18 и 25 контактов. Попробовал посадить без них, не заработала. Есть у кого схема, куда можно протянуть дорожки?

28.08.2019 в 01:51, Fomalgaut сказал:

Здравствуйте.

Проблема с Antminer D3

 

Похоже, проблема с платой управления.

Подскажите, в чём может быть проблема. Лог прилагаю.

 

  Показать содержимое

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 65280
[    0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 64768 pages, LIFO batch:15
[    0.000000] AM335X ES1.0 (neon )
[    0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768
[    0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
[    0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 255MB = 255MB total
[    0.000000] Memory: 238672k/238672k available, 23472k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0612cf0   (6188 kB)
[    0.000000]       .init : 0xc0613000 - 0xc06554c0   ( 266 kB)
[    0.000000]       .data : 0xc0656000 - 0xc06cc020   ( 473 kB)
[    0.000000]        .bss : 0xc06cc020 - 0xc0725e3c   ( 360 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000354] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[    0.015437] pid_max: default: 32768 minimum: 301
[    0.015669] Security Framework initialized
[    0.015764] Mount-cache hash table entries: 512
[    0.024592] Initializing cgroup subsys cpuacct
[    0.024627] Initializing cgroup subsys memory
[    0.024689] Initializing cgroup subsys blkio
[    0.024824] CPU: Testing write buffer coherency: ok
[    0.025391] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.025467] Setting up static identity map for 0x8038c820 - 0x8038c86c
[    0.026793] Brought up 1 CPUs
[    0.026817] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[    0.028113] devtmpfs: initialized
[    0.092521] pinctrl core: initialized pinctrl subsystem
[    0.092737] rstctl core: initialized rstctl subsystem
[    0.093231] regulator-dummy: no parameters
[    0.093803] NET: Registered protocol family 16
[    0.094507] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.104181] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
[    0.104363] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.105449] platform 49000000.edma: alias fck already exists
[    0.105484] platform 49000000.edma: alias fck already exists
[    0.105512] platform 49000000.edma: alias fck already exists
[    0.106659] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.106840] OMAP GPIO hardware version 0.1
[    0.108242] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.109566] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.110889] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.111515] of_get_named_gpio_flags exited with status 52
[    0.111547] gpio-rctrl rstctl.3: loaded OK
[    0.116651] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.119859] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.122045] cpsw.0: No hwaddr in dt. Using 94:e3:6d:f7:8e:fd from efuse
[    0.122077] cpsw.1: No hwaddr in dt. Using 94:e3:6d:f7:8e:ff from efuse
[    0.137629] bio: create slab <bio-0> at 0
[    0.149770] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[    0.150012] of_get_named_gpio_flags: can't parse gpios property
[    0.150302] vmmcsd_fixed: 3300 mV 
[    0.153429] SCSI subsystem initialized
[    0.153881] usbcore: registered new interface driver usbfs
[    0.153996] usbcore: registered new interface driver hub
[    0.154336] usbcore: registered new device driver usb
[    0.156442] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
[    0.156476] omap_i2c 4819c000.i2c: unable to select pin group
[    0.156671] media: Linux media interface: v0.10
[    0.156768] Linux video capture interface: v2.00
[    0.156887] pps_core: LinuxPPS API ver. 1 registered
[    0.156903] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.157625] Advanced Linux Sound Architecture Driver Initialized.
[    0.158820] Switching to clocksource gp_timer
[    0.176847] NET: Registered protocol family 2
[    0.177840] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.177930] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[    0.178020] TCP: Hash tables configured (established 2048 bind 2048)
[    0.178111] TCP: reno registered
[    0.178137] UDP hash table entries: 256 (order: 1, 12288 bytes)
[    0.178182] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[    0.178682] NET: Registered protocol family 1
[    0.179272] RPC: Registered named UNIX socket transport module.
[    0.179292] RPC: Registered udp transport module.
[    0.179306] RPC: Registered tcp transport module.
[    0.179320] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.179710] Trying to unpack rootfs image as initramfs...
[    1.945132] Freeing initrd memory: 12244K
[    1.945817] CPU PMU: probing PMU on CPU 0
[    1.945851] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[    1.946466] omap2_mbox_probe: platform not supported
[    1.950330] VFS: Disk quotas dquot_6.5.2
[    1.950568] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.951949] NFS: Registering the id_resolver key type
[    1.952055] Key type id_resolver registered
[    1.952072] Key type id_legacy registered
[    1.952140] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.952581] msgmni has been set to 490
[    1.955378] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.955405] io scheduler noop registered
[    1.955421] io scheduler deadline registered
[    1.955479] io scheduler cfq registered (default)
[    1.959398] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.961980] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[    1.962269] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[    2.623082] console [ttyO0] enabled
[    2.627618] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
[    2.636318] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
[    2.644958] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
[    2.653618] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
[    2.662598] [drm] Initialized drm 1.1.0 20060810
[    2.681258] brd: module loaded
[    2.691505] loop: module loaded
[    2.695681] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
[    2.705611] nand_get_flash_type: 2c,f1 against 2c,f1
[    2.711144] ONFI param page 0 valid
[    2.714818] ONFI flash detected
[    2.718138] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABAEAWP), 128MiB, page size: 2048, OOB size: 64
[    2.730050] omap2-nand: detected x8 NAND flash
[    2.734716] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    2.740299] omap2-nand: using custom ecc layout
[    2.745142] 10 ofpart partitions found on MTD device omap2-nand.0
[    2.751536] Creating 10 MTD partitions on "omap2-nand.0":
[    2.757213] 0x000000000000-0x000000020000 : "spl"
[    2.764017] 0x000000020000-0x000000040000 : "spl_backup1"
[    2.771471] 0x000000040000-0x000000060000 : "spl_backup2"
[    2.778888] 0x000000060000-0x000000080000 : "spl_backup3"
[    2.786287] 0x000000080000-0x000000240000 : "u-boot"
[    2.794548] 0x000000240000-0x000000260000 : "bootenv"
[    2.801447] 0x000000260000-0x000000280000 : "fdt"
[    2.808088] 0x000000280000-0x000000780000 : "kernel"
[    2.819035] 0x000000800000-0x000001c00000 : "root"
[    2.842525] 0x000001c00000-0x000003000000 : "config"
[    2.866310] OneNAND driver initializing
[    2.872058] usbcore: registered new interface driver asix
[    2.877870] usbcore: registered new interface driver cdc_ether
[    2.884119] usbcore: registered new interface driver smsc95xx
[    2.890240] usbcore: registered new interface driver net1080
[    2.896266] usbcore: registered new interface driver cdc_subset
[    2.902560] usbcore: registered new interface driver zaurus
[    2.908567] usbcore: registered new interface driver cdc_ncm
[    2.915327] usbcore: registered new interface driver cdc_acm
[    2.921283] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.929662] Initializing USB Mass Storage driver...
[    2.934903] usbcore: registered new interface driver usb-storage
[    2.941203] USB Mass Storage support registered.
[    2.946243] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    2.952949] musb-hdrc musb-hdrc.0.auto: pdev->id = 0
[    2.958196] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.966967] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.966989] musb-hdrc: MHDRC RTL version 2.0 
[    2.967004] musb-hdrc: setup fifo_mode 4
[    2.967031] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.967180] musb-hdrc musb-hdrc.0.auto: *** mode=3
[    2.972225] musb-hdrc musb-hdrc.0.auto: *** power=250
[    2.978241] musb-hdrc musb-hdrc.1.auto: pdev->id = 1
[    2.983493] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.992262] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.992283] musb-hdrc: MHDRC RTL version 2.0 
[    2.992297] musb-hdrc: setup fifo_mode 4
[    2.992319] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.992459] musb-hdrc musb-hdrc.1.auto: *** mode=1
[    2.997503] musb-hdrc musb-hdrc.1.auto: *** power=250
[    3.002835] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    3.009481] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
[    3.017741] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup
[    3.017845] usb usb1: default language 0x0409
[    3.017902] usb usb1: udev 1, busnum 1, minor = 0
[    3.017926] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.025056] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.032627] usb usb1: Product: MUSB HDRC host driver
[    3.037843] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd
[    3.043509] usb usb1: SerialNumber: musb-hdrc.1.auto
[    3.049474] usb usb1: usb_probe_device
[    3.049501] usb usb1: configuration #1 chosen from 1 choice
[    3.049611] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    3.049817] hub 1-0:1.0: usb_probe_interface
[    3.049839] hub 1-0:1.0: usb_probe_interface - got id
[    3.049866] hub 1-0:1.0: USB hub found
[    3.053858] hub 1-0:1.0: 1 port detected
[    3.057997] hub 1-0:1.0: standalone hub
[    3.058017] hub 1-0:1.0: individual port power switching
[    3.058035] hub 1-0:1.0: no over-current protection
[    3.058053] hub 1-0:1.0: Single TT
[    3.058074] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    3.058094] hub 1-0:1.0: power on to power good time: 10ms
[    3.058151] hub 1-0:1.0: local power source is good
[    3.058267] hub 1-0:1.0: enabling power on all ports
[    3.059356] mousedev: PS/2 mouse device common for all mice
[    3.067274] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[    3.075065] i2c /dev entries driver
[    3.080083] pps_ldisc: PPS line discipline registered
[    3.085569] Driver for 1-wire Dallas network protocol.
[    3.092887] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    3.100485] cpuidle: using governor ladder
[    3.104809] cpuidle: using governor menu
[    3.109368] of_get_named_gpio_flags exited with status 6
[    3.109387] of_get_named_gpio_flags: can't parse gpios property
[    3.109403] of_get_named_gpio_flags: can't parse gpios property
[    3.109440] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[    3.116678] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[    3.123492] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[    3.130715] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[    3.138053] mmc.4 supply vmmc_aux not found, using dummy regulator
[    3.144998] omap_hsmmc mmc.4: pins are not configured from the driver
[    3.159024] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[    3.179055] of_get_named_gpio_flags exited with status -517
[    3.179122] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.186906] ledtrig-cpu: registered to indicate activity on CPUs
[    3.193678] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[    3.200877] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[    3.208984] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[    3.215333] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[    3.222519] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[    3.234780] usbcore: registered new interface driver usbhid
[    3.240697] usbhid: USB HID core driver
[    3.247579] TCP: cubic registered
[    3.251102] Initializing XFRM netlink socket
[    3.255671] NET: Registered protocol family 17
[    3.260548] NET: Registered protocol family 15
[    3.265418] Key type dns_resolver registered
[    3.270057] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    3.278137] ThumbEE CPU extension supported.
[    3.282646] Registering SWP/SWPB emulation handler
[    3.288660] registered taskstats version 1
[    3.295275] of_get_named_gpio_flags exited with status -517
[    3.295347] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.352334] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[    3.358745] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[    3.373294] libphy: 4a101000.mdio: probed
[    3.377615] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[    3.387856] Detected MACID = 94:e3:6d:f7:8e:fd
[    3.392536] cpsw 4a100000.ethernet: NAPI disabled
[    3.397924] of_get_named_gpio_flags exited with status -517
[    3.397988] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.406704] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    3.415986] cpu0 supply cpu0 not found, using dummy regulator
[    3.422493] cpufreq_cpu0: failed to scale voltage up: -22
[    3.428312] cpufreq_cpu0: failed to scale voltage up: -22
[    3.441101] ALSA device list:
[    3.444339]   No soundcards found.
[    3.448903] Freeing init memory: 264K
[    3.452951] Failed to execute /init
[    4.447518] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    5.772932] net eth0: initializing cpsw version 1.12 (0)
[    5.781883] net eth0: phy found : id is : 0x7c0f1
[    5.787313] libphy: PHY 4a101000.mdio:01 not found
[    5.792513] net eth0: phy 4a101000.mdio:01 not found on slave 1
[    9.927066] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
Aug 27 13:30:58 (none) local0.err cgminer: Miner compile time: Tue Nov 13 11:46:56 CST 2018 type: Antminer D3
Aug 27 13:30:58 (none) local0.warn cgminer: Started cgminer 4.9.0
Aug 27 13:30:58 (none) local0.warn cgminer[362]: bitmain_DASH_init
Aug 27 13:30:59 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:30:59 (none) local0.err cgminer[362]: FAN2 too slow ...
Aug 27 13:30:59 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:30:59 (none) local0.err cgminer[362]: FAN2 too slow ...
Aug 27 13:31:00 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:00 (none) local0.err cgminer[362]: FAN2 too slow ...
Aug 27 13:31:00 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:01 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:01 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:02 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:02 (none) local0.err cgminer[362]: FAN1 too slow ...
Aug 27 13:31:03 (none) local0.warn cgminer[362]: check_fan_speed OK
Aug 27 13:31:03 (none) local0.notice cgminer[362]: detected at /sys/class/gpio/gpio51/value  chain 0
Aug 27 13:31:03 (none) local0.notice cgminer[362]: detected at /sys/class/gpio/gpio48/value  chain 1
Aug 27 13:31:03 (none) local0.notice cgminer[362]: detected at /sys/class/gpio/gpio47/value  chain 2
Aug 27 13:31:03 (none) local0.notice cgminer[362]: detect total chain num 3
Aug 27 13:31:03 (none) local0.notice cgminer[362]: i2c init ok
Aug 27 13:31:03 (none) local0.notice cgminer[362]: check_whether_need_update_pic_program
Aug 27 13:31:04 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:04 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:05 (none) local0.notice cgminer[362]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 27 13:31:06 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:06 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:07 (none) local0.notice cgminer[362]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 27 13:31:08 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:08 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:09 (none) local0.notice cgminer[362]: get_PIC16F1704_software_version_new ok, version = 0x81
Aug 27 13:31:09 (none) local0.notice cgminer[362]: every_chain_reset_PIC16F1704_pic_new
Aug 27 13:31:10 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:11 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:12 (none) local0.notice cgminer[362]: reset_PIC16F1704_pic_new ok
Aug 27 13:31:13 (none) local0.notice cgminer[362]: every_chain_jump_from_loader_to_app_PIC16F1704_new
Aug 27 13:31:13 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:14 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:14 (none) local0.notice cgminer[362]: jump_from_loader_to_app_PIC16F1704_new ok
Aug 27 13:31:15 (none) local0.notice cgminer[362]: reset_hash_board_low 0
Aug 27 13:31:15 (none) local0.notice cgminer[362]: pic_heart_beat_func_new
Aug 27 13:31:15 (none) local0.notice cgminer[362]: reset_hash_board_low 1
Aug 27 13:31:15 (none) local0.notice cgminer[362]: reset_hash_board_low 2
Aug 27 13:31:15 (none) local0.notice cgminer[362]: reset_hash_board_low 3
Aug 27 13:31:15 (none) local0.notice cgminer[362]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 27 13:31:15 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:16 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:16 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:16 (none) local0.notice cgminer[362]: reset_hash_board_high 0
Aug 27 13:31:16 (none) local0.notice cgminer[362]: reset_hash_board_high 1
Aug 27 13:31:16 (none) local0.notice cgminer[362]: reset_hash_board_high 2
Aug 27 13:31:16 (none) local0.notice cgminer[362]: reset_hash_board_high 3
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain chainid = 0
Aug 27 13:31:17 (none) local0.err cgminer[362]: create rx read thread for chain 0 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: Start A New Asic Response.Chain Id:[0]
Aug 27 13:31:17 (none) local0.err cgminer[362]: create tx read thread for chain 0 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: open device over
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain chainid = 1
Aug 27 13:31:17 (none) local0.err cgminer[362]: create rx read thread for chain 1 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: Start A New Asic Response.Chain Id:[1]
Aug 27 13:31:17 (none) local0.err cgminer[362]: create tx read thread for chain 1 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: open device over
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain chainid = 2
Aug 27 13:31:17 (none) local0.err cgminer[362]: create rx read thread for chain 2 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: Start A New Asic Response.Chain Id:[2]
Aug 27 13:31:17 (none) local0.err cgminer[362]: create tx read thread for chain 2 ok
Aug 27 13:31:17 (none) local0.notice cgminer[362]: open device over
Aug 27 13:31:17 (none) local0.notice cgminer[362]: tty_init_chain
Aug 27 13:31:17 (none) local0.notice cgminer[362]: open device over
Aug 27 13:31:18 (none) local0.notice cgminer[362]: check_every_chain_asic_number
Aug 27 13:31:18 (none) local0.warn cgminer[362]: check_asic_reg: Chain0 has 0 ASICs
Aug 27 13:31:18 (none) local0.warn cgminer[362]: check_asic_reg: Chain1 has 54 ASICs
Aug 27 13:31:18 (none) local0.warn cgminer[362]: check_asic_reg: Chain2 has 0 ASICs
Aug 27 13:31:19 (none) local0.notice cgminer[362]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 27 13:31:20 (none) local0.notice cgminer[362]: reset_hash_board_low 0
Aug 27 13:31:20 (none) local0.notice cgminer[362]: reset_hash_board_low 1
Aug 27 13:31:20 (none) local0.notice cgminer[362]: reset_hash_board_low 2
Aug 27 13:31:20 (none) local0.notice cgminer[362]: reset_hash_board_low 3
Aug 27 13:31:21 (none) local0.notice cgminer[362]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 27 13:31:21 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:21 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:21 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:22 (none) local0.notice cgminer[362]: reset_hash_board_high 0
Aug 27 13:31:22 (none) local0.notice cgminer[362]: reset_hash_board_high 1
Aug 27 13:31:22 (none) local0.notice cgminer[362]: reset_hash_board_high 2
Aug 27 13:31:22 (none) local0.notice cgminer[362]: reset_hash_board_high 3
Aug 27 13:31:22 (none) local0.notice cgminer[362]: check_every_chain_asic_number
Aug 27 13:31:22 (none) local0.warn cgminer[362]: check_asic_reg: Chain0 has 0 ASICs
Aug 27 13:31:23 (none) local0.warn cgminer[362]: check_asic_reg: Chain1 has 54 ASICs
Aug 27 13:31:23 (none) local0.warn cgminer[362]: check_asic_reg: Chain2 has 0 ASICs
Aug 27 13:31:23 (none) local0.notice cgminer[362]: recheck_asic_num DONE!
Aug 27 13:31:23 (none) local0.notice cgminer[362]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 27 13:31:24 (none) local0.notice cgminer[362]: reset_hash_board_low 0
Aug 27 13:31:24 (none) local0.notice cgminer[362]: reset_hash_board_low 1
Aug 27 13:31:24 (none) local0.notice cgminer[362]: reset_hash_board_low 2
Aug 27 13:31:24 (none) local0.notice cgminer[362]: reset_hash_board_low 3
Aug 27 13:31:25 (none) local0.notice cgminer[362]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 27 13:31:25 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:25 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:26 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:26 (none) local0.notice cgminer[362]: reset_hash_board_high 0
Aug 27 13:31:26 (none) local0.notice cgminer[362]: reset_hash_board_high 1
Aug 27 13:31:26 (none) local0.notice cgminer[362]: reset_hash_board_high 2
Aug 27 13:31:26 (none) local0.notice cgminer[362]: reset_hash_board_high 3
Aug 27 13:31:27 (none) local0.notice cgminer[362]: check_every_chain_asic_number
Aug 27 13:31:27 (none) local0.warn cgminer[362]: check_asic_reg: Chain0 has 0 ASICs
Aug 27 13:31:27 (none) local0.warn cgminer[362]: check_asic_reg: Chain1 has 54 ASICs
Aug 27 13:31:27 (none) local0.warn cgminer[362]: check_asic_reg: Chain2 has 0 ASICs
Aug 27 13:31:28 (none) local0.notice cgminer[362]: recheck_asic_num DONE!
Aug 27 13:31:28 (none) local0.notice cgminer[362]: every_chain_disable_PIC16F1704_dc_dc_new
Aug 27 13:31:28 (none) local0.notice cgminer[362]: reset_hash_board_low 0
Aug 27 13:31:28 (none) local0.notice cgminer[362]: reset_hash_board_low 1
Aug 27 13:31:28 (none) local0.notice cgminer[362]: reset_hash_board_low 2
Aug 27 13:31:28 (none) local0.notice cgminer[362]: reset_hash_board_low 3
Aug 27 13:31:29 (none) local0.notice cgminer[362]: every_chain_enable_PIC16F1704_dc_dc_new
Aug 27 13:31:29 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:30 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:30 (none) local0.notice cgminer[362]: enable_PIC16F1704_dc_dc_new ok
Aug 27 13:31:31 (none) local0.notice cgminer[362]: reset_hash_board_high 0
Aug 27 13:31:31 (none) local0.notice cgminer[362]: reset_hash_board_high 1
Aug 27 13:31:31 (none) local0.notice cgminer[362]: reset_hash_board_high 2
Aug 27 13:31:31 (none) local0.notice cgminer[362]: reset_hash_board_high 3
Aug 27 13:31:31 (none) local0.notice cgminer[362]: check_every_chain_asic_number
Aug 27 13:31:31 (none) local0.warn cgminer[362]: check_asic_reg: Chain0 has 0 ASICs
Aug 27 13:31:31 (none) local0.warn cgminer[362]: check_asic_reg: Chain1 has 54 ASICs
Aug 27 13:31:32 (none) local0.warn cgminer[362]: check_asic_reg: Chain2 has 0 ASICs
Aug 27 13:31:32 (none) local0.notice cgminer[362]: recheck_asic_num DONE!
Aug 27 13:31:32 (none) local0.notice cgminer[362]: calculate_address_interval: temp_asic_number = 64, addrInterval = 1
Aug 27 13:31:32 (none) local0.notice cgminer[362]: calculate_address_interval: CHIP_OFFSET = 0x04000000, CORE_OFFSET = 0x00800000
Aug 27 13:31:32 (none) local0.notice cgminer[362]: set_ticket_mask ticket_mask = 0x0000001b
Aug 27 13:31:32 (none) local0.notice cgminer[362]: every_chain_get_PIC16F1704_freq_new
Aug 27 13:31:34 (none) local0.notice cgminer[362]: set_frequency: frequency = 537
Aug 27 13:31:34 (none) local0.notice cgminer[362]: software_set_address_chain: chain 0 has 0 ASIC, and addrInterval is 1
Aug 27 13:31:34 (none) local0.notice cgminer[362]: Now Set [0] Chain Address
Aug 27 13:31:35 (none) local0.notice cgminer[362]: software_set_address_chain: chain 1 has 54 ASIC, and addrInterval is 1
Aug 27 13:31:35 (none) local0.notice cgminer[362]: Now Set [1] Chain Address
Aug 27 13:31:36 (none) local0.notice cgminer[362]: software_set_address_chain: chain 2 has 0 ASIC, and addrInterval is 1
Aug 27 13:31:36 (none) local0.notice cgminer[362]: Now Set [2] Chain Address
Aug 27 13:31:37 (none) local0.notice cgminer[362]: software_set_address_chain: chain 3 has 0 ASIC, and addrInterval is 1
Aug 27 13:31:37 (none) local0.notice cgminer[362]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 27 13:31:37 (none) local0.notice cgminer[362]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 27 13:31:37 (none) local0.notice cgminer[362]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 27 13:31:37 (none) local0.notice cgminer[362]: enable_read_temperature_from_asic_chain: reg_value = 0x07007a61
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: select_core_to_check_temperature_chain: diode_mux_sel = 4, vdd_mux_sel = 0
Aug 27 13:31:37 (none) local0.notice cgminer[362]: 0 calibration_sensor_offset_chain
Aug 27 13:31:37 (none) local0.notice cgminer[362]: chain:0 local:0 remote:0
Aug 27 13:31:37 (none) local0.warn cgminer[362]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 27 13:31:38 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 27 13:31:38 (none) local0.notice cgminer[362]: 1 calibration_sensor_offset_chain
Aug 27 13:31:39 (none) local0.notice cgminer[362]: chain:1 local:0 remote:0
Aug 27 13:31:39 (none) local0.warn cgminer[362]: Chain 1 set_temperature_offset_value_chain_sensor
Aug 27 13:31:40 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain1 Sensor0 temp offset : 00, 
Aug 27 13:31:40 (none) local0.notice cgminer[362]: 2 calibration_sensor_offset_chain
Aug 27 13:31:40 (none) local0.notice cgminer[362]: chain:2 local:0 remote:0
Aug 27 13:31:40 (none) local0.warn cgminer[362]: Chain 2 set_temperature_offset_value_chain_sensor
Aug 27 13:31:41 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain2 Sensor0 temp offset : 00, 
Aug 27 13:31:41 (none) local0.warn cgminer[362]: Chain 0 set_temperature_offset_value_chain
Aug 27 13:31:41 (none) local0.warn cgminer[362]: Chain 0 set_temperature_offset_value_chain_sensor
Aug 27 13:31:42 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain0 Sensor0 temp offset : 00, 
Aug 27 13:31:42 (none) local0.warn cgminer[362]: Chain 1 set_temperature_offset_value_chain
Aug 27 13:31:42 (none) local0.warn cgminer[362]: Chain 1 set_temperature_offset_value_chain_sensor
Aug 27 13:31:42 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain1 Sensor0 temp offset : 00, 
Aug 27 13:31:42 (none) local0.warn cgminer[362]: Chain 2 set_temperature_offset_value_chain
Aug 27 13:31:42 (none) local0.warn cgminer[362]: Chain 2 set_temperature_offset_value_chain_sensor
Aug 27 13:31:43 (none) local0.notice cgminer[362]: set_temperature_offset_value_chain_sensor: Chain2 Sensor0 temp offset : 00, 
Aug 27 13:31:43 (none) local0.notice cgminer[362]: frequency = '537'
Aug 27 13:31:43 (none) local0.notice cgminer[362]: dev.timeout = 562356 us
Aug 27 13:31:43 (none) local0.notice cgminer[362]: open_core_chain
Aug 27 13:31:43 (none) local0.notice cgminer[362]: open_core_chain
Aug 27 13:31:43 (none) local0.notice cgminer[362]: open_core_chain
Aug 27 13:31:44 (none) local0.notice cgminer[362]: open_core_chain
Aug 27 13:31:47 (none) local0.err cgminer[362]: cgminer time error total_secs = 1566912707.089818 last_total_secs = 1.000000
Aug 27 13:31:47 (none) local0.warn cgminer[362]: Failed to resolve (?wrong URL) stratum+tcp://:(null)
Aug 27 13:31:47 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:31:51 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:31:54 (none) local0.warn cgminer[362]: API running in IP access mode on port 4028 (16)
Aug 27 13:31:56 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:00 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:04 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:08 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:12 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:16 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:20 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:25 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:29 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:33 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:37 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:41 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:45 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:50 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:54 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:32:58 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!
Aug 27 13:33:02 (none) local0.err cgminer[362]: read_temp_func: can't read all sensor's temperature, close PIC and need reboot!!!

 

 

Причем плата управления? Там 2 лезвия в отвале. Без них запусти контрольку и посмотри логи, если на нее грешишь.

Ссылка на комментарий
Поделиться на другие сайты

Здравствуйте, кто может сказать в чем дело. На двух асиках перестали крутить вентиляторы оба. Когда включаю, то ни один не крутит вообще и только слышно как  на блоке питания работает кулер. Что делать? вентиляторы переставлял с одного на другой, толку 0. Они вставляются в разьемы на контрольной плате, поэтому может быть причина в ней?

 

Ссылка на комментарий
Поделиться на другие сайты

11 минут назад, ultratrans сказал:

Здравствуйте, кто может сказать в чем дело. На двух асиках перестали крутить вентиляторы оба. Когда включаю, то ни один не крутит вообще и только слышно как  на блоке питания работает кулер. Что делать? вентиляторы переставлял с одного на другой, толку 0. Они вставляются в разьемы на контрольной плате, поэтому может быть причина в ней?

 

У меня чаще подгорал контакт питания именно красный провод - менял контакт на штекере и зачищал ответный на плате .

Ссылка на комментарий
Поделиться на другие сайты

Всем Привет!

Подскажите пожалуйста в чем может быть  проблема?

Все вроде работает но показания не соответствует норме.

 

asik.png

Ссылка на комментарий
Поделиться на другие сайты

22 часа назад, Lesikvip сказал:

Судя по ЭТОМУ изображению, все же куда-то уходят.

Разговор был только за тот чип (место его установки) который был на вашем фото. Если говорить в общем за всю плату, то эти пины задействованы только у 62 и 63 чипа для датчика температуры и светодиодов обмена соответственно. На совсем старых ревизиях плат RF задействован на 1-м чипе.

22 часа назад, Lesikvip сказал:

Принесли плату, с отвалившимся чипом, на чипе остались пятачки от 17, 18 и 25 контактов. Попробовал посадить без них, не заработала. Есть у кого схема, куда можно протянуть дорожки?

25-й контакт задействован только на первом чипе. Между 24 и 25 контактами вешается кварц.

Смотрите внимательней в микроскоп, если есть дорога то ее видно.

Ссылка на комментарий
Поделиться на другие сайты

14 часов назад, ultratrans сказал:

Здравствуйте, кто может сказать в чем дело. На двух асиках перестали крутить вентиляторы оба. Когда включаю, то ни один не крутит вообще и только слышно как  на блоке питания работает кулер. Что делать? вентиляторы переставлял с одного на другой, толку 0. Они вставляются в разьемы на контрольной плате, поэтому может быть причина в ней?

 

Аппарат то какой? На S(T)9 кручение вентиляторов (хотябы на минимальных оборотах) никак не связано с платой управления, а связано только с наличием питания 12В. Значит у вас на плату управления не приходит 12В. Светодиоды на плате управления горят/мигают?

Ссылка на комментарий
Поделиться на другие сайты

1 час назад, Вадим Жилин сказал:

Все вроде работает но показания не соответствует норме.

Какие показания и какова их норма по вашему мнению? И если уж выкладываете скриншот, то отключите переводчик, а то непонятно где и что.

Ссылка на комментарий
Поделиться на другие сайты

11 часов назад, Вадим Жилин сказал:

показания не соответствует норме.

 

Какие показания и каким нормам?

Самому не противно смотреть на майнер через кривой переводчик?

Ссылка на комментарий
Поделиться на другие сайты

Здравствуйте!

Асик S9i

Ноли первые начинаются с больших нолей.

Частота завышена на первой плате.(Frequency(avg)

Аппаратные средства показывает на одной плате мало.(HW)

 

Ноли были большие когда смотрел через переводчик.

Получается все в норме?

 

Просто в один прекрасный момент . Асик работал но дул холодный воздух. На F2pool показывало ,что асик не работает.

Перезапустил, заработал.

Сейчас асик продул.

Пипец было всякой херни в нем.

asik1.png

Ссылка на комментарий
Поделиться на другие сайты

Для публикации сообщений создайте учётную запись или авторизуйтесь

Вы должны быть пользователем, чтобы оставить комментарий

Создать учетную запись

Зарегистрируйте новую учётную запись в нашем сообществе. Это очень просто!

Регистрация нового пользователя

Войти

Уже есть аккаунт? Войти в систему.

Войти
  • Последние посетители   0 пользователей онлайн

    • Ни одного зарегистрированного пользователя не просматривает данную страницу
  • Similar Topics

    • Antminer L3, L3+

      Доброй ночи! пожалуйста помогите кто знает с antminer l3+  работает 1.5 недели, все было хорошо.  В один момент вижу, что он выключен пришел его перезагрузил и началось   Вообщем выдает ошибку socket connect failed. connection refused то иногда включается и показывает на второй плате 21 чип место 71  много раз перезагружал, перекинул с другого асика блок питания он все равно так   не майнит уходит в ошибку   что делать подскажите пожалуйста, асику всего полторы недели скрины приложил

      в ASIC/FPGA майнеры

    • блок питания Antminer T21

      Нужен ваш совет . Есть ли какой то способ подключить Bitcoin Miner T21 190T Power supply AC Input voltage  380~415 3610W к одной фазной сети 200 - 230 вольт !? Векторный преобразователь частоты 220 > 380В сможет !? Например - https://spc.com.ua/ru/products/nietz-splc-nz2200-15gs2-vector-frequency-inverter-15kw-ip20-1phase-220v-to-3phase-380v

      в Блоки питания, ИБП, силовая часть

    • Antminer S17, S17pro, S17+, S17e, T17, T17e, T17+

      Официальный сайт | Manual | Прошивка (официальный сайт) | Прошивка (bits.media)   В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда,  F.A.Q по майнингу. Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы. Сообщения, не относящиеся к теме обсуждения (оффтоп), удаляются без предупреждения.   Технические характеристики:   Статьи на Bits.me

      в ASIC/FPGA майнеры

    • Antminer S19,-pro, S19j,-pro, S19a, S19i, S19 Hyd, S19pro Hyd, S19pro+ Hyd, T19 Hyd

      Официальный сайт | Manual | Прошивка (официальный сайт) | Прошивка (bits.media)   В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда,  F.A.Q по майнингу. Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы. Сообщения, не относящиеся к теме обсуждения (оффтоп), удаляются без предупреждения.   Технические характеристики:   Статьи на Bits.me

      в ASIC/FPGA майнеры

    • Antminer D3. Плата управления.

      Привет всем. во время прошивки отключилось питание. по всей вероятности, покривился бутлоадер. ибо, загрузится с MicroSD карты теперь невозможно. плата не переводится в аварийный режим загрузки с флешки замыканием по диагонали контактов 43 на разъёме Р8 и 3, на разъёме Р9 (или 29,30 NAND) возможно ли восстановить загрузчик через JTEG или как-то ещё? в правом верхнем углу платы, правее NAND, место под разъём MicroUSB, можно ли залить бутлоадер через него? спасибо.  

      в ASIC/FPGA майнеры

×
×
  • Создать...