Ремонт: Bitmain Antminer s7, s9, l3+

[Odo]

..может кто-то знает где взять образ img(оригинальный..битмайновский) для s9 13.5...?

[mctosh]

Так на офиц. сайте  битмайн есть.

 

[Odo]

..мне нужен образ для записи sd карты с последующей загрузки с ней..образ img(оригинальный..битмайновский) ... 

[Lexis77]

@Odo Не найдешь. Они скрывают его. А тебе для каких целей?

[Odo]

..nand платы управления неисправна..работает только c sd карты..нашел образ..прошил..работает но прошивка кастомная..с dev fee..

[mctosh]

Есть прошивка для T9-S9 она без fee

[Odo]

https://www.youtube.com/watch?v=dzArOe8KuHI

 

эту имеешь виду?

[mctosh]

Просто форматируешь карту в fat32 и закидываешь на карту содержимое архива https://file11.bitmain.com/shop-product/firmware/t9%2B -SD Tools.zip

[Lexis77]

А у меня другое чудо сегодня произошло. Есть асики 14Т, одинаковые. Шил пару из них несколько раз и все ок. А сегодня прошил другой, той же прошивкой и он стабильно стал выбирать набор на 13.5, а не 14. Я прям в шоках.

@Odo а контролька какая? На ксилинке или двухэтажная с БББ ?

[mctosh]

8 минут назад, Lexis77 сказал:

на 13.5, а не 14

А чего не прошить с фиксированной частотой на 650МГц?

[Odo]

..На ксилинке..3 платы...с sd картой работают..

 

Не знаю как у кого, но у меня этот образ работал только в режиме прошивки, т.е. перемычка как при перепрошивке карта SD вставлена. По сети плата находилась, жесткие ip сохранялись. Главный минус - нельзя прошить, только восстановление из бэкапа как у @scopus Восстановил плату следующим образом, форматируем sd в фат32, копируем t9+ из https://service.bitmain.com/support/download?product=Flashing SD card with image на sd, т.е. в корне должно быть папка bin и файлы boot.bin devicetree.dtb и т.д. Вставляем sd переключаем перемычку jp4 включаем (я делал с подключенным лан кабелем) где-то через минуту начнет с интервалом 5 секунд моргать красный с зеленым - все прошилось. Вынимаем карту, возвращаем перемычку, подключаем кабель и находим плату по сети. У нас прошилась на t9. Прошивка доступна для s9, все прошилось нормально. 2 месяца назад почему-то не получилось

 

пробовал этот метод не получается ни на одной плате...

[Lexis77]

3 минуты назад, mctosh сказал:

А чего не прошить с фиксированной частотой на 650МГц?

В том-то и фишка, что с фиксом все работает и до прошивки все работало на 14. Чел ввел в заблуждение и пришлось прошить для проверки. А возврат превратил асик в 13.5. На сколько я знаю, тип асика зашит именно в контрольке. Выходит меня майриг наебманул с этим асиком, т.к. другие после прошивок остаются 14Т

 

5 минут назад, Odo сказал:

На ксилинке

Тут не могу помочь. Сорян.

[mctosh]

9 минут назад, Lexis77 сказал:

тип асика зашит именно в контрольке

Возможно в Uboot зашиты параметры хэш плат.

 

[Lexis77]

@mctosh тем более обман.

Посмотрим что ответят. Я нацарапал им вопросы, жду.

[Splinter]

12 часов назад, Lexis77 сказал:

В том-то и фишка, что с фиксом все работает и до прошивки все работало на 14... А возврат превратил асик в 13.5. На сколько я знаю, тип асика зашит именно в контрольке... другие после прошивок остаются 14Т

Напишите версии прошивок на которой работало на 14 до прошивки, какие версии ставили в промежутке и какая сейчас, на которой 13,5. И покажите kernal log. 

Параметры hash плат находятся в самих платах. В автофрековой прошивке они принимаются к сведенью но не обязательно применяются, могут быть понижены при автофреке. В фиксированной прошивке устанавливается частота которую вы сами выбираете при первом запуске. В любом случае все это видно в kernal log

12 часов назад, mctosh сказал:

Возможно в Uboot зашиты параметры хэш плат.

 

Uboot знать не знает о существовании hash плат. 

[Lexis77]

34 минуты назад, Splinter сказал:

версии прошивок на которой работало на 14 до прошивки

Да фиг его знает. С завода что стояло, то и было.
Ставил вот такую Antminer-S9-xilinx-v003e, чтоб можно было частоту опусть низко-низко.
Возвращал на S9_all_201711171757_autofreq

Но я это проделывал и на других асиках из этой партии.

 

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000311] ps7-ttc #0 at f0006000, irq=43
[    0.000623] Console: colour dummy device 80x30
[    0.000661] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040213] pid_max: default: 32768 minimum: 301
[    0.040438] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040460] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042621] CPU: Testing write buffer coherency: ok
[    0.042983] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043046] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043272] L310 cache controller enabled
[    0.043292] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121041] CPU1: Booted secondary processor
[    0.210231] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210362] Brought up 2 CPUs
[    0.210382] SMP: Total of 2 processors activated.
[    0.210390] CPU: All CPU(s) started in SVC mode.
[    0.211057] devtmpfs: initialized
[    0.213476] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214718] regulator-dummy: no parameters
[    0.223321] NET: Registered protocol family 16
[    0.225643] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.227937] cpuidle: using governor ladder
[    0.227951] cpuidle: using governor menu
[    0.235494] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.237041] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.237056] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.237178] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.259386] bio: create slab <bio-0> at 0
[    0.260900] vgaarb: loaded
[    0.261655] SCSI subsystem initialized
[    0.262561] usbcore: registered new interface driver usbfs
[    0.262746] usbcore: registered new interface driver hub
[    0.262980] usbcore: registered new device driver usb
[    0.263529] media: Linux media interface: v0.10
[    0.263691] Linux video capture interface: v2.00
[    0.263933] pps_core: LinuxPPS API ver. 1 registered
[    0.263945] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.264071] PTP clock support registered
[    0.264440] EDAC MC: Ver: 3.0.0
[    0.265520] Advanced Linux Sound Architecture Driver Initialized.
[    0.268523] DMA-API: preallocated 4096 debug entries
[    0.268537] DMA-API: debugging enabled by kernel config
[    0.268631] Switched to clocksource arm_global_timer
[    0.289278] NET: Registered protocol family 2
[    0.289963] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.290058] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.290217] TCP: Hash tables configured (established 8192 bind 8192)
[    0.290294] TCP: reno registered
[    0.290311] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.290371] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.290648] NET: Registered protocol family 1
[    0.291021] RPC: Registered named UNIX socket transport module.
[    0.291034] RPC: Registered udp transport module.
[    0.291042] RPC: Registered tcp transport module.
[    0.291050] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.291064] PCI: CLS 0 bytes, default 64
[    0.291526] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.293614] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.295018] bounce pool size: 64 pages
[    0.295929] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.296151] msgmni has been set to 1486
[    0.296952] io scheduler noop registered
[    0.296966] io scheduler deadline registered
[    0.297007] io scheduler cfq registered (default)
[    0.306761] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.306783] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.432582] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.005300] console [ttyPS0] enabled
[    1.009596] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.017238] [drm] Initialized drm 1.1.0 20060810
[    1.034321] brd: module loaded
[    1.043833] loop: module loaded
[    1.053660] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.059517] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.067324] libphy: XEMACPS mii bus: probed
[    1.071803] ------------- phy_id = 0x3625e62
[    1.076554] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.085181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.091992] ehci-pci: EHCI PCI platform driver
[    1.099254] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.106050] usbcore: registered new interface driver usb-storage
[    1.112957] mousedev: PS/2 mouse device common for all mice
[    1.119095] i2c /dev entries driver
[    1.126033] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.131594] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.137487] Xilinx Zynq CpuIdle Driver started
[    1.142409] sdhci: Secure Digital Host Controller Interface driver
[    1.148502] sdhci: Copyright(c) Pierre Ossman
[    1.152868] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.159665] mmc0: no vqmmc regulator found
[    1.163679] mmc0: no vmmc regulator found
[    1.208646] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.217349] usbcore: registered new interface driver usbhid
[    1.222861] usbhid: USB HID core driver
[    1.227595] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.233894] nand: Micron MT29F2G08ABAEAWP
[    1.237858] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.243797] Bad block table found at page 131008, version 0x01
[    1.250024] Bad block table found at page 130944, version 0x01
[    1.256077] 3 ofpart partitions found on MTD device pl353-nand
[    1.261858] Creating 3 MTD partitions on "pl353-nand":
[    1.266948] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.275045] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.282381] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.291406] TCP: cubic registered
[    1.294643] NET: Registered protocol family 17
[    1.299363] Registering SWP/SWPB emulation handler
[    1.305287] regulator-dummy: disabling
[    1.309671] UBI: attaching mtd1 to ubi0
[    1.692513] UBI: scanning is finished
[    1.704430] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.711510] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.718251] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.724954] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.731812] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.737781] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.744912] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1134783803
[    1.753943] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.763161] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.763166] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.767166] ALSA device list:
[    1.767170]   No soundcards found.
[    1.783950] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.899284] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.905215] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.914347] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    1.924231] UBIFS: reserved for root: 0 bytes (0 KiB)
[    1.929270] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[    1.952562] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    1.963580] devtmpfs: mounted
[    1.966693] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    3.083917] random: dd urandom read with 0 bits of entropy available
[    3.708674] 
[    3.708674] bcm54xx_config_init
[    4.318673] 
[    4.318673] bcm54xx_config_init
[    8.319516] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    8.325605] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   24.736456] In axi fpga driver!
[   24.739549] request_mem_region OK!
[   24.742919] AXI fpga dev virtual address is 0xf01fe000
[   24.748022] *base_vir_addr = 0x8c510
[   24.763894] In fpga mem driver!
[   24.766963] request_mem_region OK!
[   24.770592] fpga mem virtual address is 0xf3000000
[   25.548652] 
[   25.548652] bcm54xx_config_init
[   26.178654] 
[   26.178654] bcm54xx_config_init
[   30.179497] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   30.185522] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  762.929577] random: nonblocking pool is initialized
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=0008c510
miner ID : 800cc541123b8854
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[34] has core num=1
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[55] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[42] has core num=15
Check chain[7] PIC fw version=0x03
get PIC voltage=108 on chain[5], value=880
get PIC voltage=108 on chain[6], value=880
get PIC voltage=108 on chain[7], value=880
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,-5,0,0,0,0,33,0
chain[5] temp chip I2C addr=0x98
chain[6] temp offset record: 62,-4,0,0,0,0,33,0
chain[6] temp chip I2C addr=0x98
chain[7] temp offset record: 62,-6,0,0,0,0,33,0
chain[7] temp chip I2C addr=0x98
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1483 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 800cc541123b8854
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=4320
get fan[2] speed=4320
get fan[2] speed=4320
get fan[2] speed=4320
get fan[2] speed=4320
get fan[2] speed=4320
get fan[5] speed=5400
get fan[2] speed=4320
get fan[5] speed=5400
get fan[2] speed=4320
get fan[5] speed=5400
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=2 : 2
Chain[J6] has backup chain_voltage=880
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=2 : 2
Chain[J7] has backup chain_voltage=860
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=2 : 2
Chain[J8] has backup chain_voltage=860
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=108 value=880
Chain[J7] orignal chain_voltage_pic=108 value=880
Chain[J7] will use backup chain_voltage_pic=860 [142]
Chain[J7] get working chain_voltage_pic=142
Chain[J8] orignal chain_voltage_pic=108 value=880
Chain[J8] will use backup chain_voltage_pic=860 [142]
Chain[J8] get working chain_voltage_pic=142
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[34] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[55] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[42] has core num=15
miner total rate=13877GH/s fixed rate=13500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=-5
Chain:5 base freq=631
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631 
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631 
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631 
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631 
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631 
Chain:5 max freq=631
Chain:5 min freq=631

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=-4
Chain:6 base freq=650
Asic[ 0]:650 
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 
Chain:6 max freq=650
Chain:6 min freq=650

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=-6
Chain:7 base freq=662
Asic[ 0]:662 
Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662 Asic[ 8]:662 
Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662 Asic[16]:662 
Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662 Asic[24]:662 
Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662 Asic[29]:662 Asic[30]:662 Asic[31]:662 Asic[32]:662 
Asic[33]:662 Asic[34]:662 Asic[35]:662 Asic[36]:662 Asic[37]:662 Asic[38]:662 Asic[39]:662 Asic[40]:662 
Asic[41]:662 Asic[42]:662 Asic[43]:662 Asic[44]:662 Asic[45]:662 Asic[46]:662 Asic[47]:662 Asic[48]:662 
Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662 
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662 
Chain:7 max freq=662
Chain:7 min freq=662


Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=-5
Chain:5 base freq=631
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631 
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631 
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631 
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631 
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631 
Chain:5 max freq=631
Chain:5 min freq=631

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=-4
Chain:6 base freq=650
Asic[ 0]:631 
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631 
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631 
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631 
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:637 
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637 
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637 
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637 
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637 
Chain:6 max freq=637
Chain:6 min freq=631

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=-6
Chain:7 base freq=662
Asic[ 0]:643 
Asic[ 1]:643 Asic[ 2]:643 Asic[ 3]:643 Asic[ 4]:643 Asic[ 5]:643 Asic[ 6]:643 Asic[ 7]:643 Asic[ 8]:643 
Asic[ 9]:643 Asic[10]:643 Asic[11]:643 Asic[12]:643 Asic[13]:643 Asic[14]:643 Asic[15]:643 Asic[16]:643 
Asic[17]:643 Asic[18]:643 Asic[19]:643 Asic[20]:643 Asic[21]:643 Asic[22]:643 Asic[23]:643 Asic[24]:643 
Asic[25]:643 Asic[26]:643 Asic[27]:643 Asic[28]:643 Asic[29]:643 Asic[30]:643 Asic[31]:643 Asic[32]:643 
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643 
Asic[41]:643 Detect a bad chip=42 on chain[7], fixed to 400M
Asic[42]:662 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643 
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 
Chain:7 max freq=662
Chain:7 min freq=643

max freq = 662
set baud=1
Chain[J6] PIC temp offset=62,-5,0,0,0,0,33,0
chain[5] temp chip I2C addr=0x98
Chain[J6] chip[244] use PIC middle temp offset=-5 typeID=55
New offset Chain[5] chip[244] local:30 remote:32 offset:28 
Chain[J6] chip[244] get middle temp offset=28 typeID=55
Chain[J7] PIC temp offset=62,-4,0,0,0,0,33,0
chain[6] temp chip I2C addr=0x98
Chain[J7] chip[244] use PIC middle temp offset=-4 typeID=55
New offset Chain[6] chip[244] local:30 remote:32 offset:28 
Chain[J7] chip[244] get middle temp offset=28 typeID=55
Chain[J8] PIC temp offset=62,-6,0,0,0,0,33,0
chain[7] temp chip I2C addr=0x98
Chain[J8] chip[244] use PIC middle temp offset=-6 typeID=55
New offset Chain[7] chip[244] local:31 remote:35 offset:26 
Chain[J8] chip[244] get middle temp offset=26 typeID=55
single board rate=4531 voltage limit=880 on chain[5]
get PIC voltage=880 on chain[5], check: must be < 880
single board rate=4552 voltage limit=880 on chain[6]
get PIC voltage=860 on chain[6], check: must be < 880
single board rate=4552 voltage limit=880 on chain[7]
get PIC voltage=860 on chain[7], check: must be < 880
Chain[J6] set working voltage=880 [108]
Chain[J7] set working voltage=860 [142]
Chain[J8] set working voltage=860 [142]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=911	asic[28]=911	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=911	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!

asic[27]=911
core[080]=7	

asic[28]=911
core[080]=7	

asic[34]=911
core[058]=7	



freq[00]=631	freq[01]=631	freq[02]=631	freq[03]=631	freq[04]=631	freq[05]=631	freq[06]=631	freq[07]=631	
freq[08]=631	freq[09]=631	freq[10]=631	freq[11]=631	freq[12]=631	freq[13]=631	freq[14]=631	freq[15]=631	
freq[16]=631	freq[17]=631	freq[18]=631	freq[19]=631	freq[20]=631	freq[21]=631	freq[22]=631	freq[23]=631	
freq[24]=631	freq[25]=631	freq[26]=631	freq[27]=631	freq[28]=631	freq[29]=631	freq[30]=631	freq[31]=631	
freq[32]=631	freq[33]=631	freq[34]=631	freq[35]=631	freq[36]=631	freq[37]=631	freq[38]=631	freq[39]=631	
freq[40]=631	freq[41]=631	freq[42]=631	freq[43]=631	freq[44]=631	freq[45]=631	freq[46]=631	freq[47]=631	
freq[48]=631	freq[49]=631	freq[50]=631	freq[51]=631	freq[52]=631	freq[53]=631	freq[54]=631	freq[55]=631	
freq[56]=631	freq[57]=631	freq[58]=631	freq[59]=631	freq[60]=631	freq[61]=631	freq[62]=631	

total valid nonce number:57453
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:47221
last_nonce_num:33779
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=631	freq[01]=631	freq[02]=631	freq[03]=631	freq[04]=631	freq[05]=631	freq[06]=631	freq[07]=631	
freq[08]=631	freq[09]=631	freq[10]=631	freq[11]=631	freq[12]=631	freq[13]=631	freq[14]=631	freq[15]=631	
freq[16]=631	freq[17]=631	freq[18]=631	freq[19]=631	freq[20]=631	freq[21]=631	freq[22]=631	freq[23]=631	
freq[24]=631	freq[25]=631	freq[26]=631	freq[27]=631	freq[28]=631	freq[29]=631	freq[30]=631	freq[31]=631	
freq[32]=637	freq[33]=637	freq[34]=637	freq[35]=637	freq[36]=637	freq[37]=637	freq[38]=637	freq[39]=637	
freq[40]=637	freq[41]=637	freq[42]=637	freq[43]=637	freq[44]=637	freq[45]=637	freq[46]=637	freq[47]=637	
freq[48]=637	freq[49]=637	freq[50]=637	freq[51]=637	freq[52]=637	freq[53]=637	freq[54]=637	freq[55]=637	
freq[56]=637	freq[57]=637	freq[58]=637	freq[59]=637	freq[60]=637	freq[61]=637	freq[62]=637	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25984
last_nonce_num:28620
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=643	freq[01]=643	freq[02]=643	freq[03]=643	freq[04]=643	freq[05]=643	freq[06]=643	freq[07]=643	
freq[08]=643	freq[09]=643	freq[10]=643	freq[11]=643	freq[12]=643	freq[13]=643	freq[14]=643	freq[15]=643	
freq[16]=643	freq[17]=643	freq[18]=643	freq[19]=643	freq[20]=643	freq[21]=643	freq[22]=643	freq[23]=643	
freq[24]=643	freq[25]=643	freq[26]=643	freq[27]=643	freq[28]=643	freq[29]=643	freq[30]=643	freq[31]=643	
freq[32]=643	freq[33]=643	freq[34]=643	freq[35]=643	freq[36]=643	freq[37]=643	freq[38]=643	freq[39]=643	
freq[40]=643	freq[41]=643	freq[42]=662	freq[43]=643	freq[44]=643	freq[45]=643	freq[46]=643	freq[47]=643	
freq[48]=643	freq[49]=643	freq[50]=643	freq[51]=643	freq[52]=643	freq[53]=650	freq[54]=650	freq[55]=650	
freq[56]=650	freq[57]=650	freq[58]=650	freq[59]=650	freq[60]=650	freq[61]=650	freq[62]=650	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26260
last_nonce_num:35753
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: OK!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: OK!
do heat board 8xPatten for 2 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=631	freq[01]=631	freq[02]=631	freq[03]=631	freq[04]=631	freq[05]=631	freq[06]=631	freq[07]=631	
freq[08]=631	freq[09]=631	freq[10]=631	freq[11]=631	freq[12]=631	freq[13]=631	freq[14]=631	freq[15]=631	
freq[16]=631	freq[17]=631	freq[18]=631	freq[19]=631	freq[20]=631	freq[21]=631	freq[22]=631	freq[23]=631	
freq[24]=631	freq[25]=631	freq[26]=631	freq[27]=631	freq[28]=631	freq[29]=631	freq[30]=631	freq[31]=631	
freq[32]=631	freq[33]=631	freq[34]=631	freq[35]=631	freq[36]=631	freq[37]=631	freq[38]=631	freq[39]=631	
freq[40]=631	freq[41]=631	freq[42]=631	freq[43]=631	freq[44]=631	freq[45]=631	freq[46]=631	freq[47]=631	
freq[48]=631	freq[49]=631	freq[50]=631	freq[51]=631	freq[52]=631	freq[53]=631	freq[54]=631	freq[55]=631	
freq[56]=631	freq[57]=631	freq[58]=631	freq[59]=631	freq[60]=631	freq[61]=631	freq[62]=631	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25881
last_nonce_num:29684
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=631	freq[01]=631	freq[02]=631	freq[03]=631	freq[04]=631	freq[05]=631	freq[06]=631	freq[07]=631	
freq[08]=631	freq[09]=631	freq[10]=631	freq[11]=631	freq[12]=631	freq[13]=631	freq[14]=631	freq[15]=631	
freq[16]=631	freq[17]=631	freq[18]=631	freq[19]=631	freq[20]=631	freq[21]=631	freq[22]=631	freq[23]=631	
freq[24]=631	freq[25]=631	freq[26]=631	freq[27]=631	freq[28]=631	freq[29]=631	freq[30]=631	freq[31]=631	
freq[32]=637	freq[33]=637	freq[34]=637	freq[35]=637	freq[36]=637	freq[37]=637	freq[38]=637	freq[39]=637	
freq[40]=637	freq[41]=637	freq[42]=637	freq[43]=637	freq[44]=637	freq[45]=637	freq[46]=637	freq[47]=637	
freq[48]=637	freq[49]=637	freq[50]=637	freq[51]=637	freq[52]=637	freq[53]=637	freq[54]=637	freq[55]=637	
freq[56]=637	freq[57]=637	freq[58]=637	freq[59]=637	freq[60]=637	freq[61]=637	freq[62]=637	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26003
last_nonce_num:22558
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=643	freq[01]=643	freq[02]=643	freq[03]=643	freq[04]=643	freq[05]=643	freq[06]=643	freq[07]=643	
freq[08]=643	freq[09]=643	freq[10]=643	freq[11]=643	freq[12]=643	freq[13]=643	freq[14]=643	freq[15]=643	
freq[16]=643	freq[17]=643	freq[18]=643	freq[19]=643	freq[20]=643	freq[21]=643	freq[22]=643	freq[23]=643	
freq[24]=643	freq[25]=643	freq[26]=643	freq[27]=643	freq[28]=643	freq[29]=643	freq[30]=643	freq[31]=643	
freq[32]=643	freq[33]=643	freq[34]=643	freq[35]=643	freq[36]=643	freq[37]=643	freq[38]=643	freq[39]=643	
freq[40]=643	freq[41]=643	freq[42]=662	freq[43]=643	freq[44]=643	freq[45]=643	freq[46]=643	freq[47]=643	
freq[48]=643	freq[49]=643	freq[50]=643	freq[51]=643	freq[52]=643	freq[53]=650	freq[54]=650	freq[55]=650	
freq[56]=650	freq[57]=650	freq[58]=650	freq[59]=650	freq[60]=650	freq[61]=650	freq[62]=650	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26264
last_nonce_num:29682
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: OK!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: OK!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: OK!
setStartTimePoint total_tv_start_sys=219 total_tv_end_sys=220
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=70.1790 Asic[02]=69.2390 Asic[03]=68.8200 Asic[04]=67.7460 Asic[05]=73.9030 Asic[06]=69.4240 Asic[07]=67.7460 Asic[08]=73.6010 
Asic[09]=70.7490 Asic[10]=72.8130 Asic[11]=70.1620 Asic[12]=75.9330 Asic[13]=70.6320 Asic[14]=72.1250 Asic[15]=73.9870 Asic[16]=69.1890 
Asic[17]=72.5110 Asic[18]=73.8360 Asic[19]=67.2430 Asic[20]=72.6450 Asic[21]=68.8530 Asic[22]=68.5510 Asic[23]=73.6010 Asic[24]=74.8930 
Asic[25]=70.7660 Asic[26]=75.4470 Asic[27]=72.3930 Asic[28]=70.3630 Asic[29]=67.7460 Asic[30]=68.5340 Asic[31]=72.1580 Asic[32]=70.0780 
Asic[33]=68.4840 Asic[34]=73.6010 Asic[35]=73.0140 Asic[36]=71.3360 Asic[37]=66.8060 Asic[38]=77.2080 Asic[39]=69.4400 Asic[40]=77.8460 
Asic[41]=69.1220 Asic[42]=68.1650 Asic[43]=71.6050 Asic[44]=70.2290 Asic[45]=77.5440 Asic[46]=73.6680 Asic[47]=71.4870 Asic[48]=69.0040 
Asic[49]=72.3260 Asic[50]=66.8400 Asic[51]=76.0170 Asic[52]=72.9800 Asic[53]=68.2320 Asic[54]=72.5270 Asic[55]=69.2390 Asic[56]=70.3800 
Asic[57]=71.2690 Asic[58]=73.0140 Asic[59]=70.4130 Asic[60]=74.8760 Asic[61]=72.1580 Asic[62]=65.1620 Asic[63]=68.6850 

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=66.2360 Asic[02]=69.0040 Asic[03]=71.1180 Asic[04]=72.1080 Asic[05]=65.9170 Asic[06]=74.6410 Asic[07]=72.6450 Asic[08]=70.5480 
Asic[09]=71.2360 Asic[10]=68.7860 Asic[11]=73.2820 Asic[12]=74.8760 Asic[13]=72.9800 Asic[14]=71.1520 Asic[15]=70.8160 Asic[16]=70.0610 
Asic[17]=70.1790 Asic[18]=68.6850 Asic[19]=69.0710 Asic[20]=69.2890 Asic[21]=73.5840 Asic[22]=67.1590 Asic[23]=77.9460 Asic[24]=77.5440 
Asic[25]=71.6380 Asic[26]=76.7220 Asic[27]=70.3970 Asic[28]=74.8430 Asic[29]=76.5040 Asic[30]=72.8460 Asic[31]=73.7350 Asic[32]=65.9510 
Asic[33]=69.3230 Asic[34]=65.9680 Asic[35]=68.5850 Asic[36]=72.0580 Asic[37]=76.6710 Asic[38]=76.6210 Asic[39]=69.9100 Asic[40]=70.6150 
Asic[41]=76.6880 Asic[42]=75.6140 Asic[43]=73.1820 Asic[44]=72.5780 Asic[45]=73.4500 Asic[46]=71.1350 Asic[47]=72.5780 Asic[48]=68.7360 
Asic[49]=71.7050 Asic[50]=68.7020 Asic[51]=77.0240 Asic[52]=75.1950 Asic[53]=71.0850 Asic[54]=77.5100 Asic[55]=74.8090 Asic[56]=70.9340 
Asic[57]=72.1080 Asic[58]=69.3570 Asic[59]=68.5010 Asic[60]=67.7790 Asic[61]=66.2360 Asic[62]=69.7760 Asic[63]=70.3130 

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=75.0440 Asic[02]=74.5910 Asic[03]=66.4710 Asic[04]=75.4800 Asic[05]=75.2120 Asic[06]=74.5240 Asic[07]=74.6410 Asic[08]=74.0880 
Asic[09]=71.9740 Asic[10]=73.2990 Asic[11]=71.6210 Asic[12]=72.2930 Asic[13]=71.7560 Asic[14]=72.5950 Asic[15]=72.9800 Asic[16]=72.0240 
Asic[17]=75.3460 Asic[18]=75.1950 Asic[19]=68.5010 Asic[20]=80.2950 Asic[21]=71.0340 Asic[22]=70.7660 Asic[23]=71.9740 Asic[24]=71.7220 
Asic[25]=76.0670 Asic[26]=75.6820 Asic[27]=75.6480 Asic[28]=76.0340 Asic[29]=72.1750 Asic[30]=74.1550 Asic[31]=73.5680 Asic[32]=75.8330 
Asic[33]=71.3530 Asic[34]=70.7490 Asic[35]=75.1780 Asic[36]=75.6480 Asic[37]=74.5070 Asic[38]=65.0450 Asic[39]=73.4670 Asic[40]=71.6720 
Asic[41]=74.6080 Asic[42]=72.8970 Asic[43]=48.6030 Asic[44]=71.7390 Asic[45]=71.6720 Asic[46]=71.9230 Asic[47]=72.0740 Asic[48]=80.3460 
Asic[49]=66.0510 Asic[50]=74.5570 Asic[51]=77.3930 Asic[52]=70.9000 Asic[53]=74.4400 Asic[54]=77.5610 Asic[55]=74.3730 Asic[56]=73.7520 
Asic[57]=70.1280 Asic[58]=77.4430 Asic[59]=73.7020 Asic[60]=72.1420 Asic[61]=76.0340 Asic[62]=74.1040 Asic[63]=73.0310 
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=28
Chain[5] Chip[62] local Temp=66
Chain[5] Chip[62] middle Temp=76
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=28
Chain[6] Chip[62] local Temp=59
Chain[6] Chip[62] middle Temp=71
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=26
read failed, old value: Chain[7] Chip[62] local Temp=62
Chain[7] Chip[62] middle Temp=73
Done read temp on Chain[7]
Set fixed full fan speed
FAN PWM: 100
read_temp_func Done!
CRC error counter=0

 

 

[Splinter]

@Lexis77 Ваши hash платы в сумме рассчитаны на 13,955 Th, т.е. у вас конфигурация на 14Th. Однако при автофреке  частота на платах понижается. Странность в том, что в конфигах 2-й и 3-й плат прописаны низкие напряжения. Эти же платы при автофреке и понижают частоту.

Вывод - не пользуйтесь левыми прошивками, кто знает что они вам там понаделали с системой. Стоковые прошивки не трогают заводские  настройки в платах. 

[Lexis77]

@Splinter а мне как раз только что с майрига ответили...
 

Цитата

К сожалению, теперь только накатывание прошивки на хешплаты. У них тоже есть своя память.

 

[Splinter]

@Lexis77 Я думаю они правы. Однако как вариант, если та прошивка которая понизила вам напряжения действительно пишет в память hash плат, то этот процесс должен быть обратимым. Т.е. предлагаю поставить ту левую прошивку и там уже по обстоятельствам, смотря что вы на ней делали. Если только понижали частоты. То выставите по платам частоты 631 Мгц, 650 МГц и 662 МГц. Если там есть возможность в явном виде задавать напряжения, то выставите на всех платах 8,8-8,9 В. Сейчас на 2-й и 3-й платах выставлено 8,6В.

[Lexis77]

Попробую

[guruykin]

Во какая хрень у меня с 9 произошла и главное работала , звук посторонний был но задний вентель проверил (казалось что звук идет с задней части) все норм месяца два проработала потом отключилась ушла из сети, решил разобрать заодно почистить и вот что обнаружил , остатки лопостей вывалились и внутренности от корпуса вентилятора отвалились.

[Lexis77]

@guruykin с вероятностью 100%, треснула одна лопасть, а когда отвалилась, его и понесло в вальхалу , причем последнй выдох был почти моментальным. Бывает.

[Lexis77]

@Splinter все перепробовал, все равно прописывает 13.5. Залил прошивку на 650 и забил. Он с ней даже лучше работает, чем с автофреком.

[guruykin]

@Lexis77  Привет Лешь я не читал более ранние страницы но в суть твоей проблеммы въехал. Пробовал ли поставить 550. Она типо все из памяти стирает и потом можешь ставить что хочешь. На своем опоте скажу после прошивки с FEE хотел поставить родную не получалось , тоже посоветовали накатил 550 потом автофреком и все вышло.

550 я имел в виду битмайновскую

[Lexis77]

@guruykin хм.. сейчас попробую. Только почему именно 550?