Ремонт: Bitmain Antminer s7, s9, l3+

sdslot86 · 15 фев 2019, 10:12

В чем может быть проблема несколько S9 работают после запуска часа 3-4 нормально, и температура держится 85-90. Потом судя по логам асик останавливается из за высокого нагрева 150 градусов на плате.

Цитата

Chain[7] set working voltage=880 [108]
restartNum = 2 , auto-reinit enabled...
setStartTimePoint total_tv_start_sys=79206 total_tv_end_sys=79207
Error: set_BC_write_command wait buffer ready timeout!
Error: clement debug: wait BC ready timeout, PLUG ON=0x000000e0..
Error: set_BC_write_command wait buffer ready timeout!
Error: clement debug: wait BC ready timeout, PLUG ON=0x000000e0..
Error: set_BC_write_command wait buffer ready timeout!
Error: clement debug: wait BC ready timeout, PLUG ON=0x000000e0..
Error: set_BC_write_command wait buffer ready timeout!
Error: clement debug: wait BC ready timeout, PLUG ON=0x000000e0..
Error: set_BC_write_command wait buffer ready timeout!
Error: clement debug: wait BC ready timeout, PLUG ON=0x000000e0..
Error: set_BC_write_command wait buffer ready timeout!
Error: clement debug: wait BC ready timeout, PLUG ON=0x000000e0..
Error: set_BC_write_command wait buffer ready timeout!
Error: clement debug: wait BC ready timeout, PLUG ON=0x000000e0..
[Thu Jan 1 23:17:22 1970] Fatal Error: Temperature is too high!
[Thu Jan 1 23:17:33 1970] Fatal Error: Temperature is too high!
[Thu Jan 1 23:17:44 1970] Fatal Error: Temperature is too high!
[Thu Jan 1 23:17:55 1970] Fatal Error: Temperature is too high!
[Thu Jan 1 23:18:06 1970] Fatal Error: Temperature is too high!
[Thu Jan 1 23:18:18 1970] Fatal Error: Temperature is too high!
[Thu Jan 1 23:18:29 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:18:40 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:18:51 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:19:02 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:19:13 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:19:24 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:19:35 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:19:46 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:19:57 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:20:08 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:20:19 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:20:30 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:20:41 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:20:52 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:21:03 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:21:14 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:21:25 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:21:36 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:21:47 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:21:58 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:22:09 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:22:21 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:22:32 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:22:43 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:22:54 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:23:05 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:23:16 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:23:27 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:23:38 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:23:49 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:24:00 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:24:11 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:24:22 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:24:33 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:24:44 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:24:55 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:25:06 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:25:17 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:25:28 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:25:39 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:25:50 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:26:01 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:26:12 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:26:24 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:26:35 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:26:46 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:26:57 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:27:08 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:27:19 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:27:30 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:27:41 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:27:52 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:28:03 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:28:14 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:28:25 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:28:36 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:28:47 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:28:58 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:29:09 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:29:20 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:29:31 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:29:42 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:29:53 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:30:04 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:30:15 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:30:27 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:30:38 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:30:49 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:31:00 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:31:11 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:31:22 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:31:33 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:31:44 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:31:55 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:32:06 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:32:17 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:32:28 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:32:39 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:32:50 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:33:01 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:33:12 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:33:23 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:33:34 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:33:45 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:33:56 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:34:07 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:34:18 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:34:29 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:34:41 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:34:52 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:35:03 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:35:14 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:35:25 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:35:36 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:35:47 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:35:58 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:36:09 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:36:20 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:36:31 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:36:42 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:36:53 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:37:04 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:37:15 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:37:26 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:37:37 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:37:48 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:37:59 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:38:10 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:38:21 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:38:32 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:38:44 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:38:55 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:39:06 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:39:17 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:39:28 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:39:39 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:39:50 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:40:01 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:40:12 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:40:23 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:40:34 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:40:45 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:40:56 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:41:07 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:41:18 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:41:29 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:41:40 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:41:51 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:42:02 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:42:13 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:42:24 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:42:35 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:42:47 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:42:58 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:43:09 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:43:20 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:43:31 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:43:42 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:43:53 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:44:04 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:44:15 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:44:26 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:44:37 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:44:48 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:44:59 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:45:10 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:45:21 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:45:32 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:45:43 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:45:54 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:46:05 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:46:16 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:46:27 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:46:38 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:46:50 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:47:01 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:47:12 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:47:23 1970] Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
[Thu Jan 1 23:47:34 1970] Fatal Error: Temperature is too high!
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[5]: (asic index start from 1-63)

get RT hashrate from Chain[6]: (asic index start from 1-63)

get RT hashrate from Chain[7]: (asic index start from 1-63)
Check Chain[5] ASIC RT error: (asic index start from 1-63)
Asic[01]=36028797.002000
Asic[02]=218802.000000
Asic[03]=267856.000000
Asic[04]=36028797.002000
Asic[05]=36028797.002000
Asic[06]=27296462.652000
Asic[07]=36028797.002000
Asic[08]=2534168.412000
Asic[09]=36028797.002000
Asic[10]=36028797.002000
Asic[11]=36028797.002000
Asic[12]=36028797.002000
Asic[13]=255090.000000
Asic[14]=36028797.002000
Asic[15]=36028797.002000
Asic[16]=18859410.793000
Asic[17]=36028797.002000
Asic[18]=36028797.002000
Asic[19]=36028797.002000
Asic[20]=8989456.744000
Asic[21]=565149.000000
Asic[22]=36028797.002000
Asic[23]=36028797.002000
Asic[24]=36028797.002000
Asic[25]=36028797.002000
Asic[26]=36028797.002000
Asic[27]=36028797.002000
Asic[28]=15503117.172000
Asic[29]=36028797.002000
Asic[30]=36028797.002000
Asic[31]=36028797.002000
Asic[32]=36028797.002000
Asic[33]=36028797.002000
Asic[34]=36028797.002000
Asic[35]=36028797.002000
Asic[36]=36028797.002000
Asic[37]=36028797.002000
Asic[38]=36028797.002000
Asic[39]=141802.000000
Asic[40]=36028797.002000
Asic[41]=36028797.002000
Asic[42]=36028797.002000
Asic[43]=36028797.002000
Asic[44]=36028797.002000
Asic[45]=35396546.795000
Asic[46]=36028797.002000
Asic[47]=36028797.002000
Asic[48]=31198.600000
Asic[49]=2551281.440000
Asic[50]=35940285.192000
Asic[51]=36028797.002000
Asic[52]=36028797.002000
Asic[53]=36028797.002000
Asic[54]=36028797.002000
Asic[55]=15463363.962000
Asic[56]=278176.000000
Asic[57]=203139.000000
Asic[58]=1097.430000
Asic[59]=36028797.002000
Asic[60]=36028797.002000
Asic[61]=36028797.002000
Asic[62]=36028797.002000
Asic[63]=36028797.002000
Check Chain[6] ASIC RT error: (asic index start from 1-63)
Check Chain[7] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=28
read failed, old value: Chain[6] Chip[62] local Temp=143
read failed on Chain[6] Chip[62] middle Temp old value:158
Special fix Chain[6] Chip[62] middle Temp = 158
Done read temp on Chain[6]
do read temp on Chain[7]
Done read temp on Chain[7]
set FAN speed according to: temp_highest=143 temp_top1[PWM_T]=158 temp_top1[TEMP_POS_LOCAL]=143 temp_change=61 fix_fan_steps=-10
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=26844

ASIC REPAIR · 15 фев 2019, 11:29

1 час назад, sdslot86 сказал:

В чем может быть проблема несколько S9 работают после запуска часа 3-4 нормально, и температура держится 85-90. Потом судя по логам асик останавливается из за высокого нагрева 150 градусов на плате.

Вентиляторы правильно стоят? Они отображаются?

Покажите полный скрин Miner Status

sdslot86 · 15 фев 2019, 12:15

46 минут назад, ASIC REPAIR сказал:

Вентиляторы правильно стоят? Они отображаются?

Покажите полный скрин Miner Status

ASIC REPAIR · 15 фев 2019, 12:31

9 минут назад, sdslot86 сказал:

я так понимаю что Вы показываете два разных аппарата. В первом сообщении у Вас разгонная прошивка. Судя по кусочку скрина - на первой и второй плате чипов меньше положенного.

На втором скрине у Вас перестает работать аппарат в первые пол часа. Если старая прошивка - обновить на свежую. Посмотреть на все платы визуально, может забиты пылью, грязью. Посмотреть как расположены вентиляторы. Они должны пропускать поток воздуха через аппарат.

Попробуйте проделать эти операции, если так же работать будет - нужны логи аппарата, если там есть дефект - увидим.

2 часа назад, sdslot86 сказал:

В чем может быть проблема несколько S9 работают после запуска часа 3-4 нормально, и температура держится 85-90. Потом судя по логам асик останавливается из за высокого нагрева 150 градусов на плате.

Температура очень критическая, настоятельно советую открутить 4 болта, достать плату и посмотреть визуально, возможно у Вас чипы "поплыли" из за перегрева.

FozziWozzi · 15 фев 2019, 17:28

Всем здравствуйте. Прошу вашей помощи. Дело вот в чём, сегодня, по какому-то феерическому стечение обстоятельств на блоке питания была перепутана полярность подключения кабеля, то есть на майнера (неизвестной мне модели и марки) зашёл плюс вместо минуса и минус вместо плюса. Вопрос, чем грозит такое неправильное подключение? Есть ли в асиках защита от неправильной полярности? Что могло произойти, т.к. со слов подключавшего "оно щёлкнуло и тишина"? Я новичок на данном форуме, но поиск по "полярности" не выдал никаких результатов в данной теме.

UPD: Пишу в эту тему, т.к. предполагаю, что именно подобные устройства используются на ферме.

Изменено 15 фев 2019, 17:34 пользователем FozziWozzi

scopus · 16 фев 2019, 05:34

12 часов назад, FozziWozzi сказал:

Вопрос, чем грозит такое неправильное подключение?

Выходом из строя майнера.

12 часов назад, FozziWozzi сказал:

Есть ли в асиках защита от неправильной полярности?

Ваш ответ:

12 часов назад, FozziWozzi сказал:

(неизвестной мне модели и марки)

Нам оно не известно тем более.

12 часов назад, FozziWozzi сказал:

именно подобные устройства используются на ферме

Какие?

Изменено 16 фев 2019, 06:07 пользователем scopus

Комрад · 16 фев 2019, 08:12

У меня был опыт переполюсовки. Вылетел блок питания, битмайновский.

FozziWozzi · 16 фев 2019, 21:57

16 часов назад, scopus сказал:

15.02.2019 в 20:28, FozziWozzi сказал:

именно подобные устройства используются на ферме

Какие?

topic/25227-ремонт-antminer-s7-s9-обмен-опытом вроде же топик об этих

scopus · 17 фев 2019, 17:35

@FozziWozzi из Вашего текста сюда же можно включить и блоки питания.... а таких используется масса разных...

FozziWozzi · 17 фев 2019, 18:55

1 час назад, scopus сказал:

@FozziWozzi из Вашего текста сюда же можно включить и блоки питания.... а таких используется масса разных...

Блок питания остался цел. "щелчок" был в конечном устройстве.

DeNNN · 19 фев 2019, 15:52

наглядно показана работа тестера для хешплат s9

forexmuller · 20 фев 2019, 01:11

26.09.2018 в 07:07, Splinter сказал:

Тогда понятно. Контролька пытается восстановить (прошить) область app, но у нее это не выходит. Возможно она же эту область и прибила. По идеи boot целый и app должен бы прошиться, но нет.

Прошивайте полной прошивкой с соседнего лезвия. Вместе с этим проверьте качество шлейфа и надежность соединения в разъемах.

Прошивку делайте с обязательной верификацией. Возможно мрет память PIC'а.

Подскажите пожалуйста, аналогичная проблема, только дохлых 3 платы. Уже приобрел pickit3, где скачать прошивку pic-а?

mctosh · 20 фев 2019, 10:34

Видно, что в аппарате использована контрольная плата с готового айсика, с UART снимают инфу в консоль, аппаратно подключили строчный дисплей, прошивка "допилена" до режима диагностики.

Думаю, что дисплей не нужен, наверняка можно и через консоль узнать необходимую информацию.

yaudaff · 22 фев 2019, 16:39

18.12.2018 в 21:14, alexey7mechanic сказал:

Может кому то будет нужна прошивка для тестов плат S9 и T9. Знаю много чего еще можно дабавить но и так норм помогает в ремонте плат.

Repair_s9_t9_fw.tar.gz:

https://ru.files.fm/u/9pdh3nmp

https://dropmefiles.com/NC6P5

https://filecloud.me/tzjjpppd8fgi.html

Уважаемые мастера выложите пожалуйста еще раз данную прошивку у кого есть , не успел скачать может и мне поможет в диагностике.

большое спасибо

Djo · 22 фев 2019, 21:48

Гайс, дайте и мне такую прошивку для тестов с9 :bye:

alexey7mechanic · 25 фев 2019, 09:42

On 2/22/2019 at 11:48 PM, Djo said:

Гайс, дайте и мне такую прошивку для тестов с9

Напишите почту, я скину.

ricka_elf · 26 фев 2019, 06:11

Господа, всем привет!

Столкнулся с проблемой
Закупил с11 несколько штук, 2 дня проработали все. Сегодня ночью одна машина перестала соединяться с пулом. Помогите, пожалуйста, диагностировать проблему!

Прикладываю лог

Скрытый текст


Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 199152K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30224K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17184K (cca39000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 25/12, WL threshold: 4096, image sequence number: 2074935720
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 34787B34-C944-4179-A9B1-F16D63ADF901, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2602310842
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID B6A08683-A40B-48E6-9626-74BBB58666A9, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
main.c:13937: log_level = 4
main.c:13964: This is XILINX board. Totalram:       239353856
main.c:13982: Detect 256MB control board of XILINX
driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6fa0000
driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d
driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5da4000
driver-bitmain.c:995: forceFreq=-1 forceFlag=0
driver-bitmain.c:1697: min work minertest[0]:912


main.c:8515: DETECT HW version=000ab00d
main.c:14009: miner ID : 8174c4267910481c
main.c:14038: Miner Type = S9+
main.c:14046: AsicType = 1387
main.c:14049: real AsicNum = 84
main.c:14142: use critical mode to search freq...
driver-bitmain.c:1877: get PLUG ON=0x00000007
driver-bitmain.c:1947: Find hashboard on Chain[0]
driver-bitmain.c:1947: Find hashboard on Chain[1]
driver-bitmain.c:1947: Find hashboard on Chain[2]
dsPIC33EP16GS202.c:164: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:164: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:164: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
main.c:2173: chain[0] PIC jump to app
dsPIC33EP16GS202.c:117: dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[0]!
dsPIC33EP16GS202.c:117: dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[0]!
dsPIC33EP16GS202.c:117: dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[0]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[0]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[0]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[0]!
main.c:2178: Check chain[0] PIC fw version=0xff
main.c:2173: chain[1] PIC jump to app
main.c:2178: Check chain[1] PIC fw version=0xa4
main.c:2173: chain[2] PIC jump to app
main.c:2178: Check chain[2] PIC fw version=0xa4
main.c:8830: Chain[0] read_freq_badcores : 0x7d 0xd7 0x56 0x56 0x5a 0x56 0x5a 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x07 0x1b 0x00 0x00 0xc8 0x45 0x54 0x44 0x51 0x44 0x45 0x05 0x55 0x14 0x54 0x51 0x44 0x11 0x45 0x15 0x14 0x15 0x51 0x45 0x41 0x45 0x3d 0x16 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8842: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8861: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8948: has freq in PIC, will disable freq setting.
main.c:9022: chain[0] has freq in PIC and will jump over...
main.c:9024: Chain[0] has core num in PIC
main.c:8830: Chain[1] read_freq_badcores : 0x7d 0xd7 0x56 0x56 0x5a 0x56 0x5a 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x5a 0x56 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x28 0x1b 0x00 0x00 0xc8 0x54 0x44 0x51 0x05 0x55 0x50 0x54 0x14 0x45 0x51 0x54 0x14 0x54 0x11 0x45 0x54 0x44 0x45 0x51 0x51 0x44 0x49 0x15 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8842: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8861: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8948: has freq in PIC, will disable freq setting.
main.c:9022: chain[1] has freq in PIC and will jump over...
main.c:9024: Chain[1] has core num in PIC
main.c:8830: Chain[2] read_freq_badcores : 0x7d 0xd7 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0xaf 0x1b 0x00 0x00 0xc8 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x77 0x16 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8842: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8861: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8948: has freq in PIC, will disable freq setting.
main.c:9022: chain[2] has freq in PIC and will jump over...
main.c:9024: Chain[2] has core num in PIC
main.c:9128: get PIC voltage=0 on chain[0], value=930
main.c:9128: get PIC voltage=0 on chain[1], value=930
main.c:9128: get PIC voltage=138 on chain[2], value=730
main.c:3512: chain[0] heart beat fail 1 times.
main.c:9294: chain[0] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9311: chain[0] temp chip I2C addr=0x98
main.c:9294: chain[1] temp offset record: 24,-5,45,-5,0,0,33,0
main.c:9311: chain[1] temp chip I2C addr=0x98
main.c:9294: chain[2] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9311: chain[2] temp chip I2C addr=0x98
main.c:13901: total_exist_chain_num = 3
main.c:14583: restart Miner chance num=0
main.c:14623: waiting for receive_func to exit!
main.c:14637: waiting for pic heart to exit!
main.c:13872: bmminer not found= 1041 root      2156 S    grep bmminer

main.c:14681: bmminer not found, restart bmminer ...
driver-btm-c5.c:12205:bitmain_c5_init: This is the first time running after searching freq!
driver-btm-c5.c:12265:bitmain_c5_init: Detect 256MB control board of XILINX
driver-btm-c5.c:12284:bitmain_c5_init: Miner Type = S9+
driver-btm-c5.c:12291:bitmain_c5_init: Miner compile time: Fri Jan 25 22:45:00 CST 2019 type: Antminer S11
driver-btm-c5.c:12371:bitmain_c5_init: miner ID : 8174c4267910481c
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=480
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=480
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=480
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[1] speed=4440
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
driver-btm-c5.c:12528:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[1] speed=4560
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!

Еще вопрос, в каком столбце цифры с температурой чипов? Если с обоих, то почему разница почти в 2 раза?

scopus · 26 фев 2019, 06:50

А что с температурой?

Они похоже просто замерзли..

ricka_elf · 26 фев 2019, 06:52

12 минут назад, scopus сказал:

А что с температурой?

Они похоже просто замерзли..

Если про скины, то хотел бы узнать Temp(Chip2) температура чипов на с11? Если да, то возможно замерзли, но с9 при в том же помещении работают при 50-65

Или Вы спрашиваете про лог?

Изменено 26 фев 2019, 07:03 пользователем ricka_elf

scopus · 26 фев 2019, 07:40

@ricka_elf про скрины. Вы же не забывайте, S9 и S11 все такие разные ..

Изменено 26 фев 2019, 07:41 пользователем scopus

ASIC REPAIR · 26 фев 2019, 07:41

1 час назад, ricka_elf сказал:

Господа, всем привет!

Столкнулся с проблемой
Закупил с11 несколько штук, 2 дня проработали все. Сегодня ночью одна машина перестала соединяться с пулом. Помогите, пожалуйста, диагностировать проблему!

Прикладываю лог

Показать содержимое



Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 199152K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30224K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17184K (cca39000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 25/12, WL threshold: 4096, image sequence number: 2074935720
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 34787B34-C944-4179-A9B1-F16D63ADF901, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2602310842
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID B6A08683-A40B-48E6-9626-74BBB58666A9, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
main.c:13937: log_level = 4
main.c:13964: This is XILINX board. Totalram:       239353856
main.c:13982: Detect 256MB control board of XILINX
driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6fa0000
driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d
driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5da4000
driver-bitmain.c:995: forceFreq=-1 forceFlag=0
driver-bitmain.c:1697: min work minertest[0]:912


main.c:8515: DETECT HW version=000ab00d
main.c:14009: miner ID : 8174c4267910481c
main.c:14038: Miner Type = S9+
main.c:14046: AsicType = 1387
main.c:14049: real AsicNum = 84
main.c:14142: use critical mode to search freq...
driver-bitmain.c:1877: get PLUG ON=0x00000007
driver-bitmain.c:1947: Find hashboard on Chain[0]
driver-bitmain.c:1947: Find hashboard on Chain[1]
driver-bitmain.c:1947: Find hashboard on Chain[2]
dsPIC33EP16GS202.c:164: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:164: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:164: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
main.c:2173: chain[0] PIC jump to app
dsPIC33EP16GS202.c:117: dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[0]!
dsPIC33EP16GS202.c:117: dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[0]!
dsPIC33EP16GS202.c:117: dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[0]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[0]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[0]!
dsPIC33EP16GS202.c:61: dsPIC33EP16GS202_get_pic_sw_version failed on Chain[0]!
main.c:2178: Check chain[0] PIC fw version=0xff
main.c:2173: chain[1] PIC jump to app
main.c:2178: Check chain[1] PIC fw version=0xa4
main.c:2173: chain[2] PIC jump to app
main.c:2178: Check chain[2] PIC fw version=0xa4
main.c:8830: Chain[0] read_freq_badcores : 0x7d 0xd7 0x56 0x56 0x5a 0x56 0x5a 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x07 0x1b 0x00 0x00 0xc8 0x45 0x54 0x44 0x51 0x44 0x45 0x05 0x55 0x14 0x54 0x51 0x44 0x11 0x45 0x15 0x14 0x15 0x51 0x45 0x41 0x45 0x3d 0x16 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8842: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8861: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8948: has freq in PIC, will disable freq setting.
main.c:9022: chain[0] has freq in PIC and will jump over...
main.c:9024: Chain[0] has core num in PIC
main.c:8830: Chain[1] read_freq_badcores : 0x7d 0xd7 0x56 0x56 0x5a 0x56 0x5a 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x56 0x5a 0x5a 0x56 0x56 0x56 0x56 0x5a 0x5a 0x56 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x56 0x5a 0x56 0x5a 0x56 0x56 0x56 0x5a 0x56 0x56 0x5a 0x56 0x5a 0x56 0x28 0x1b 0x00 0x00 0xc8 0x54 0x44 0x51 0x05 0x55 0x50 0x54 0x14 0x45 0x51 0x54 0x14 0x54 0x11 0x45 0x54 0x44 0x45 0x51 0x51 0x44 0x49 0x15 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8842: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8861: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8948: has freq in PIC, will disable freq setting.
main.c:9022: chain[1] has freq in PIC and will jump over...
main.c:9024: Chain[1] has core num in PIC
main.c:8830: Chain[2] read_freq_badcores : 0x7d 0xd7 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0x5a 0xaf 0x1b 0x00 0x00 0xc8 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x77 0x16 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8842: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8861: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8948: has freq in PIC, will disable freq setting.
main.c:9022: chain[2] has freq in PIC and will jump over...
main.c:9024: Chain[2] has core num in PIC
main.c:9128: get PIC voltage=0 on chain[0], value=930
main.c:9128: get PIC voltage=0 on chain[1], value=930
main.c:9128: get PIC voltage=138 on chain[2], value=730
main.c:3512: chain[0] heart beat fail 1 times.
main.c:9294: chain[0] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9311: chain[0] temp chip I2C addr=0x98
main.c:9294: chain[1] temp offset record: 24,-5,45,-5,0,0,33,0
main.c:9311: chain[1] temp chip I2C addr=0x98
main.c:9294: chain[2] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9311: chain[2] temp chip I2C addr=0x98
main.c:13901: total_exist_chain_num = 3
main.c:14583: restart Miner chance num=0
main.c:14623: waiting for receive_func to exit!
main.c:14637: waiting for pic heart to exit!
main.c:13872: bmminer not found= 1041 root      2156 S    grep bmminer

main.c:14681: bmminer not found, restart bmminer ...
driver-btm-c5.c:12205:bitmain_c5_init: This is the first time running after searching freq!
driver-btm-c5.c:12265:bitmain_c5_init: Detect 256MB control board of XILINX
driver-btm-c5.c:12284:bitmain_c5_init: Miner Type = S9+
driver-btm-c5.c:12291:bitmain_c5_init: Miner compile time: Fri Jan 25 22:45:00 CST 2019 type: Antminer S11
driver-btm-c5.c:12371:bitmain_c5_init: miner ID : 8174c4267910481c
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=480
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=480
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=480
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[1] speed=4440
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
driver-btm-c5.c:12528:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3031:check_fan_beforeInit: get fan[1] speed=4560
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!
dsPIC33EP16GS202.c:166:dsPIC33EP16GS202_reset_pic: dsPIC33EP16GS202_reset_pic failed on Chain[0]!

Похоже что проблема у Вас с питанием на первой плате, она не включается и остальные следом.

S11 в ремонт поступают с неисправными блоками питания, не исключено что и Вы столкнулись с этой проблемой.

scopus · 26 фев 2019, 07:42

Да и вентиляторы чуть выше 2000 оборотов...это считай ни о чем..

@ricka_elf Занеси в тепло прогрей включи, если не пойдет, то тогда уже слушай @ASIC REPAIR

Порой не нужно усложнять..

ricka_elf · 26 фев 2019, 07:45

1 минуту назад, scopus сказал:

Да и вентиляторы чуть выше 2000 оборотов...это считай ни о чем..

@ricka_elf Занеси в тепло прогрей включи, если не пойдет, то тогда уже слушай @ASIC REPAIR

Да, спасибо!
Так и сделаю.

@ASIC REPAIR я попробую согреть, если не получится, то свяжусь с Вами. может отправлю на ремонт

mctosh · 26 фев 2019, 08:35

А почему такое большое количество ошибок? Правда нет информации как долго они работают... Но явно не здоровое что то с ним!

asic.s9.asic · 26 фев 2019, 14:26

Добрый день. Одна из машин asic s9 не работает на любом пуле. Сбрасывать до заводских настроек пробовал. Просьба посмотреть может есть что в логах.
Просьба о помощи)

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000]    Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000]    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000313] ps7-ttc #0 at df804000, irq=43
[ 0.000619] Console: colour dummy device 80x30
[ 0.000651] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040213] pid_max: default: 32768 minimum: 301
[ 0.040429] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040450] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042584] CPU: Testing write buffer coherency: ok
[ 0.042919] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042977] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043205] L310 cache controller enabled
[ 0.043225] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121038] CPU1: Booted secondary processor
[ 0.210233] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210366] Brought up 2 CPUs
[ 0.210385] SMP: Total of 2 processors activated.
[ 0.210394] CPU: All CPU(s) started in SVC mode.
[ 0.211084] devtmpfs: initialized
[ 0.213484] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214689] regulator-dummy: no parameters
[ 0.222360] NET: Registered protocol family 16
[ 0.224649] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226936] cpuidle: using governor ladder
[ 0.226949] cpuidle: using governor menu
[ 0.234390] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235921] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235935] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.236049] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.258100] bio: create slab <bio-0> at 0
[ 0.259502] vgaarb: loaded
[ 0.260299] SCSI subsystem initialized
[ 0.261733] usbcore: registered new interface driver usbfs
[ 0.261919] usbcore: registered new interface driver hub
[ 0.262151] usbcore: registered new device driver usb
[ 0.262678] media: Linux media interface: v0.10
[ 0.262834] Linux video capture interface: v2.00
[ 0.263073] pps_core: LinuxPPS API ver. 1 registered
[ 0.263084] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.263207] PTP clock support registered
[ 0.263567] EDAC MC: Ver: 3.0.0
[ 0.264613] Advanced Linux Sound Architecture Driver Initialized.
[ 0.267443] DMA-API: preallocated 4096 debug entries
[ 0.267457] DMA-API: debugging enabled by kernel config
[ 0.267530] Switched to clocksource arm_global_timer
[ 0.287697] NET: Registered protocol family 2
[ 0.288556] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.288615] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.288700] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.288747] TCP: reno registered
[ 0.288765] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288799] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.289030] NET: Registered protocol family 1
[ 0.289389] RPC: Registered named UNIX socket transport module.
[ 0.289402] RPC: Registered udp transport module.
[ 0.289410] RPC: Registered tcp transport module.
[ 0.289419] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.289432] PCI: CLS 0 bytes, default 64
[ 0.289872] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.291908] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.294034] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.294235] msgmni has been set to 967
[ 0.295027] io scheduler noop registered
[ 0.295040] io scheduler deadline registered
[ 0.295080] io scheduler cfq registered (default)
[ 0.307946] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.307966] dma-pl330 f8003000.ps7-dma:    DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.432320] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.999714] console [ttyPS0] enabled
[ 1.003949] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.011582] [drm] Initialized drm 1.1.0 20060810
[ 1.028719] brd: module loaded
[ 1.038110] loop: module loaded
[ 1.047487] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.053359] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.061410] libphy: XEMACPS mii bus: probed
[ 1.065779] ------------- phy_id = 0x3625e62
[ 1.070838] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.079468] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.086084] ehci-pci: EHCI PCI platform driver
[ 1.093317] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.100160] usbcore: registered new interface driver usb-storage
[ 1.106997] mousedev: PS/2 mouse device common for all mice
[ 1.113169] i2c /dev entries driver
[ 1.120174] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.125659] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.131566] Xilinx Zynq CpuIdle Driver started
[ 1.136404] sdhci: Secure Digital Host Controller Interface driver
[ 1.142572] sdhci: Copyright(c) Pierre Ossman
[ 1.146841] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.153703] mmc0: no vqmmc regulator found
[ 1.157750] mmc0: no vmmc regulator found
[ 1.197549] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.206263] usbcore: registered new interface driver usbhid
[ 1.211774] usbhid: USB HID core driver
[ 1.216497] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.222797] nand: Micron MT29F2G08ABAEAWP
[ 1.226760] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.232708] Bad block table found at page 131008, version 0x01
[ 1.238939] Bad block table found at page 130944, version 0x01
[ 1.244989] 3 ofpart partitions found on MTD device pl353-nand
[ 1.250770] Creating 3 MTD partitions on "pl353-nand":
[ 1.255860] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263942] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.271259] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.280197] TCP: cubic registered
[ 1.283433] NET: Registered protocol family 17
[ 1.288147] Registering SWP/SWPB emulation handler
[ 1.294055] regulator-dummy: disabling
[ 1.298412] UBI: attaching mtd1 to ubi0
[ 1.825540] UBI: scanning is finished
[ 1.837174] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.844257] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.851018] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.857703] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.864540] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.870541] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.877664] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1283732989
[ 1.886674] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.895908] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.895914] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.899854] ALSA device list:
[ 1.899857] No soundcards found.
[ 1.916275] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.977172] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.983133] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.992236] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.002120] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.007149] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model
[ 2.018683] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.026087] devtmpfs: mounted
[ 2.029222] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.865797] random: dd urandom read with 0 bits of entropy available
[ 3.257568]
[ 3.257568] bcm54xx_config_init
[ 3.867567]
[ 3.867567] bcm54xx_config_init
[ 6.868397] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 6.874489] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 22.613231] In axi fpga driver!
[ 22.616300] request_mem_region OK!
[ 22.619724] AXI fpga dev virtual address is 0xdf9fc000
[ 22.624798] *base_vir_addr = 0x8c510
[ 22.640241] In fpga mem driver!
[ 22.643313] request_mem_region OK!
[ 22.646875] fpga mem virtual address is 0xe2000000
[ 23.447553]
[ 23.447553] bcm54xx_config_init
[ 24.077549]
[ 24.077549] bcm54xx_config_init
[ 27.078423] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 27.084440] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
Find Force Freq=600 will search Freq again!
DETECT HW version=0008c510
miner ID : 807c45225c208814
config file found, will disable freq setting.
Miner Type = S9
AsicType = 1387
real AsicNum = 63
Find /tmp/searcherror: F:1 The last log is below:
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
Find Force Freq=600 will search Freq again!
DETECT HW version=0008c510
miner ID : 807c45225c208814
config file found, will disable freq setting.
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[5]...
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[6]...
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[7]...
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[5], value=870
get PIC voltage=125 on chain[6], value=870
get PIC voltage=125 on chain[7], value=870
set voltage=870 search freq on chain[5]
now set pic voltage=125 on chain[5]
set voltage=870 search freq on chain[6]
now set pic voltage=125 on chain[6]
set voltage=870 search freq on chain[7]
now set pic voltage=125 on chain[7]
enable_pic_dac on chain[5]
enable_pic_dac on chain[6]
enable_pic_dac on chain[7]
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
check chain[5]: asicNum = 63
check chain[6]: asicNum = 63
check chain[7]: asicNum = 63
After Get ASIC NUM CRC error counter=0
set_baud=0
SEARCH_FREQ_TEST_LEVEL mode set freq=650 voltage=870 on chain[5]
SEARCH_FREQ_TEST_LEVEL mode set freq=650 voltage=870 on chain[6]
SEARCH_FREQ_TEST_LEVEL mode set freq=650 voltage=870 on chain[7]
The min freq=650
set real timeout 56, need sleep=408576
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456

freq[00]=650   freq[01]=650   freq[02]=650   freq[03]=650   freq[04]=650   freq[05]=650   freq[06]=650   freq[07]=650
freq[08]=650   freq[09]=650   freq[10]=650   freq[11]=650   freq[12]=650   freq[13]=650   freq[14]=650   freq[15]=650
freq[16]=650   freq[17]=650   freq[18]=650   freq[19]=650   freq[20]=650   freq[21]=650   freq[22]=650   freq[23]=650
freq[24]=650   freq[25]=650   freq[26]=650   freq[27]=650   freq[28]=650   freq[29]=650   freq[30]=650   freq[31]=650
freq[32]=650   freq[33]=650   freq[34]=650   freq[35]=650   freq[36]=650   freq[37]=650   freq[38]=650   freq[39]=650
freq[40]=650   freq[41]=650   freq[42]=650   freq[43]=650   freq[44]=650   freq[45]=650   freq[46]=650   freq[47]=650
freq[48]=650   freq[49]=650   freq[50]=650   freq[51]=650   freq[52]=650   freq[53]=650   freq[54]=650   freq[55]=650
freq[56]=650   freq[57]=650   freq[58]=650   freq[59]=650   freq[60]=650   freq[61]=650   freq[62]=650

total valid nonce number:56959
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:13914
last_nonce_num:2970
get nonces on chain[6]
require nonce number:912
require validnonce number:57456

freq[00]=650   freq[01]=650   freq[02]=650   freq[03]=650   freq[04]=650   freq[05]=650   freq[06]=650   freq[07]=650
freq[08]=650   freq[09]=650   freq[10]=650   freq[11]=650   freq[12]=650   freq[13]=650   freq[14]=650   freq[15]=650
freq[16]=650   freq[17]=650   freq[18]=650   freq[19]=650   freq[20]=650   freq[21]=650   freq[22]=650   freq[23]=650
freq[24]=650   freq[25]=650   freq[26]=650   freq[27]=650   freq[28]=650   freq[29]=650   freq[30]=650   freq[31]=650
freq[32]=650   freq[33]=650   freq[34]=650   freq[35]=650   freq[36]=650   freq[37]=650   freq[38]=650   freq[39]=650
freq[40]=650   freq[41]=650   freq[42]=650   freq[43]=650   freq[44]=650   freq[45]=650   freq[46]=650   freq[47]=650
freq[48]=650   freq[49]=650   freq[50]=650   freq[51]=650   freq[52]=650   freq[53]=650   freq[54]=650   freq[55]=650
freq[56]=650   freq[57]=650   freq[58]=650   freq[59]=650   freq[60]=650   freq[61]=650   freq[62]=650

total valid nonce number:57039
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:13920
last_nonce_num:2996
get nonces on chain[7]
require nonce number:912
require validnonce number:57456

freq[00]=650   freq[01]=650   freq[02]=650   freq[03]=650   freq[04]=650   freq[05]=650   freq[06]=650   freq[07]=650
freq[08]=650   freq[09]=650   freq[10]=650   freq[11]=650   freq[12]=650   freq[13]=650   freq[14]=650   freq[15]=650
freq[16]=650   freq[17]=650   freq[18]=650   freq[19]=650   freq[20]=650   freq[21]=650   freq[22]=650   freq[23]=650
freq[24]=650   freq[25]=650   freq[26]=650   freq[27]=650   freq[28]=650   freq[29]=650   freq[30]=650   freq[31]=650
freq[32]=650   freq[33]=650   freq[34]=650   freq[35]=650   freq[36]=650   freq[37]=650   freq[38]=650   freq[39]=650
freq[40]=650   freq[41]=650   freq[42]=650   freq[43]=650   freq[44]=650   freq[45]=650   freq[46]=650   freq[47]=650
freq[48]=650   freq[49]=650   freq[50]=650   freq[51]=650   freq[52]=650   freq[53]=650   freq[54]=650   freq[55]=650
freq[56]=650   freq[57]=650   freq[58]=650   freq[59]=650   freq[60]=650   freq[61]=650   freq[62]=650

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:14028
last_nonce_num:2987
checkBoardState chain[5] rate=4440 bad_chip_num=3 lowest rate=4666 ret=0
Detect Higher Rate = 4440 > 0 on chain[5] freq=650 voltage=870
checkBoardState chain[6] rate=4589 bad_chip_num=1 lowest rate=4666 ret=0
Detect Higher Rate = 4589 > 0 on chain[6] freq=650 voltage=870
checkBoardState chain[7] rate=4668 bad_chip_num=0 lowest rate=4666 ret=2
SEARCH_FREQ_TEST_LEVEL get BOARD_FREQ_OK on chain[7]
special fix hash_voltage pic value = 125 [870] of Chain[7], voladded=0

Write freq to PIC :
Freq[00]=650
Freq[01]=650   Freq[02]=650   Freq[03]=650   Freq[04]=650   Freq[05]=650   Freq[06]=650   Freq[07]=650
Freq[08]=650   Freq[09]=650   Freq[10]=650   Freq[11]=650   Freq[12]=650   Freq[13]=650   Freq[14]=650
Freq[15]=650   Freq[16]=650   Freq[17]=650   Freq[18]=650   Freq[19]=650   Freq[20]=650   Freq[21]=650
Freq[22]=650   Freq[23]=650   Freq[24]=650   Freq[25]=650   Freq[26]=650   Freq[27]=650   Freq[28]=650
Freq[29]=650   Freq[30]=650   Freq[31]=650   Freq[32]=650   Freq[33]=650   Freq[34]=650   Freq[35]=650
Freq[36]=650   Freq[37]=650   Freq[38]=650   Freq[39]=650   Freq[40]=650   Freq[41]=650   Freq[42]=650
Freq[43]=650   Freq[44]=650   Freq[45]=650   Freq[46]=650   Freq[47]=650   Freq[48]=650   Freq[49]=650
Freq[50]=650   Freq[51]=650   Freq[52]=650   Freq[53]=650   Freq[54]=650   Freq[55]=650   Freq[56]=650
Freq[57]=650   Freq[58]=650   Freq[59]=650   Freq[60]=650   Freq[61]=650   Freq[62]=650
Chain[7] bad core info:

After TEST CRC error counter=0
check FAN Speed Error: fan[2] speed=600

Ремонт: Bitmain Antminer s7, s9, l3+

Рекомендуемые сообщения

Ссылка на комментарий

Поделиться на другие сайты

Топ авторов темы

Популярные дни

Топ авторов темы

Популярные дни

Популярные посты

alexey7mechanic

adv

adv

Изображения в теме

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Ссылка на комментарий

Поделиться на другие сайты

Для публикации сообщений создайте учётную запись или авторизуйтесь

Создать учетную запись

Войти

Последние посетители 0 пользователей онлайн

Similar Topics

Ресурсы

О Форуме

Соц.сети

Почта