Antminer. Все модели

archik · 30 мар 2018, 10:39

@d1aloog напряжение БП, напряжение сети, в порядке?

Merdanjan · 3 апр 2018, 21:41

Здравствуйте. Помогите пожалуйста. У меня стоят 5 асиков S9. Все работало норм, перегревов особых не было, максимум доходило до 80 градусов. Но сегодня столкнулся с такой проблемой. Средняя плата выдавал маленький хэш, вместо 63 чипов видел только 3, я разобрал все контакты и заново всунул. Не помогла та же картина. Потом смотрю свет (красный) на двух по бокам горя, но по середине которая не горит и как будто средняя плата сверху чуть чуть искривился, руками дергаю в правильном направлении, он опять горит. Бумагой зафиксиривал и заработало. Выдавало все ок. Когда перезагрузил через час где-то, опять та же ошибка. В чем может быть проблема? Как будто внутри плата отлетела что-ли.

Вот кернел лог:

Скрытый текст

[ 0.000000] Booting Linux on physical CPU 0x0

[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017

[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d

[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] Machine model: Xilinx Zynq

[ 0.000000] cma: CMA: reserved 128 MiB at 16800000

[ 0.000000] Memory policy: Data cache writealloc

[ 0.000000] On node 0 totalpages: 126976

[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000

[ 0.000000] Normal zone: 992 pages used for memmap

[ 0.000000] Normal zone: 0 pages reserved

[ 0.000000] Normal zone: 126976 pages, LIFO batch:31

[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768

[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096

[ 0.000000] pcpu-alloc: [0] 0 [0] 1

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984

[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait

[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)

[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)

[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)

[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)

[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)

[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)

[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)

[ 0.000000] Preemptible hierarchical RCU implementation.

[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.

[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.

[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

[ 0.000000] NR_IRQS:16 nr_irqs:16 16

[ 0.000000] ps7-slcr mapped to df802000

[ 0.000000] zynq_clock_init: clkc starts at df802100

[ 0.000000] Zynq clock init

[ 0.000016] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns

[ 0.000307] ps7-ttc #0 at df804000, irq=43

[ 0.000616] Console: colour dummy device 80x30

[ 0.000648] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)

[ 0.040207] pid_max: default: 32768 minimum: 301

[ 0.040427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.040448] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.042574] CPU: Testing write buffer coherency: ok

[ 0.042912] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[ 0.042973] Setting up static identity map for 0x4c4b00 - 0x4c4b58

[ 0.043197] L310 cache controller enabled

[ 0.043217] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB

[ 0.121034] CPU1: Booted secondary processor

[ 0.210227] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001

[ 0.210361] Brought up 2 CPUs

[ 0.210381] SMP: Total of 2 processors activated.

[ 0.210389] CPU: All CPU(s) started in SVC mode.

[ 0.211051] devtmpfs: initialized

[ 0.213461] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

[ 0.214672] regulator-dummy: no parameters

[ 0.222339] NET: Registered protocol family 16

[ 0.224577] DMA: preallocated 256 KiB pool for atomic coherent allocations

[ 0.226871] cpuidle: using governor ladder

[ 0.226884] cpuidle: using governor menu

[ 0.234318] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered

[ 0.235840] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.

[ 0.235854] hw-breakpoint: maximum watchpoint size is 4 bytes.

[ 0.235968] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000

[ 0.257707] bio: create slab <bio-0> at 0

[ 0.259131] vgaarb: loaded

[ 0.259836] SCSI subsystem initialized

[ 0.260923] usbcore: registered new interface driver usbfs

[ 0.261132] usbcore: registered new interface driver hub

[ 0.261371] usbcore: registered new device driver usb

[ 0.261906] media: Linux media interface: v0.10

[ 0.262071] Linux video capture interface: v2.00

[ 0.262312] pps_core: LinuxPPS API ver. 1 registered

[ 0.262452] PTP clock support registered

[ 0.262805] EDAC MC: Ver: 3.0.0

[ 0.263862] Advanced Linux Sound Architecture Driver Initialized.

[ 0.266699] DMA-API: preallocated 4096 debug entries

[ 0.266713] DMA-API: debugging enabled by kernel config

[ 0.266791] Switched to clocksource arm_global_timer

[ 0.287336] NET: Registered protocol family 2

[ 0.287990] TCP established hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.288046] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.288131] TCP: Hash tables configured (established 4096 bind 4096)

[ 0.288179] TCP: reno registered

[ 0.288195] UDP hash table entries: 256 (order: 1, 8192 bytes)

[ 0.288228] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[ 0.288463] NET: Registered protocol family 1

[ 0.288804] RPC: Registered named UNIX socket transport module.

[ 0.288816] RPC: Registered udp transport module.

[ 0.288825] RPC: Registered tcp transport module.

[ 0.288833] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.288846] PCI: CLS 0 bytes, default 64

[ 0.289280] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available

[ 0.291303] futex hash table entries: 512 (order: 3, 32768 bytes)

[ 0.293629] msgmni has been set to 967

[ 0.294409] io scheduler noop registered

[ 0.294422] io scheduler deadline registered

[ 0.294466] io scheduler cfq registered (default)

[ 0.303742] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208

[ 0.303763] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16

[ 0.429166] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps

[ 0.997256] console [ttyPS0] enabled

[ 1.001548] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000

[ 1.009191] [drm] Initialized drm 1.1.0 20060810

[ 1.026215] brd: module loaded

[ 1.035618] loop: module loaded

[ 1.045042] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k

[ 1.058999] libphy: XEMACPS mii bus: probed

[ 1.063373] ------------- phy_id = 0x3625e62

[ 1.068413] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54

[ 1.077018] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 1.083660] ehci-pci: EHCI PCI platform driver

[ 1.090909] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?

[ 1.097737] usbcore: registered new interface driver usb-storage

[ 1.104581] mousedev: PS/2 mouse device common for all mice

[ 1.110721] i2c /dev entries driver

[ 1.117663] zynq-edac f8006000.ps7-ddrc: ecc not enabled

[ 1.123148] cpufreq_cpu0: failed to get cpu0 regulator: -19

[ 1.129114] Xilinx Zynq CpuIdle Driver started

[ 1.133955] sdhci: Secure Digital Host Controller Interface driver

[ 1.140075] sdhci: Copyright(c) Pierre Ossman

[ 1.144390] sdhci-pltfm: SDHCI platform and OF driver helper

[ 1.151236] mmc0: no vqmmc regulator found

[ 1.155252] mmc0: no vmmc regulator found

[ 1.196822] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA

[ 1.205501] usbcore: registered new interface driver usbhid

[ 1.211008] usbhid: USB HID core driver

[ 1.215715] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda

[ 1.222001] nand: Micron MT29F2G08ABAEAWP

[ 1.225976] nand: 256MiB, SLC, page size: 2048, OOB size: 64

[ 1.231921] Bad block table found at page 131008, version 0x01

[ 1.238163] Bad block table found at page 130944, version 0x01

[ 1.244212] 3 ofpart partitions found on MTD device pl353-nand

[ 1.249986] Creating 3 MTD partitions on "pl353-nand":

[ 1.255085] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"

[ 1.263149] 0x000002000000-0x00000b000000 : "angstram-rootfs"

[ 1.270466] 0x00000b000000-0x000010000000 : "upgrade-rootfs"

[ 1.279405] TCP: cubic registered

[ 1.282640] NET: Registered protocol family 17

[ 1.287379] Registering SWP/SWPB emulation handler

[ 1.293257] regulator-dummy: disabling

[ 1.297606] UBI: attaching mtd1 to ubi0

[ 1.823731] UBI: scanning is finished

[ 1.835341] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0

[ 1.842422] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

[ 1.849184] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

[ 1.855848] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

[ 1.862726] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0

[ 1.868707] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

[ 1.875815] UBI: max/mean erase counter: 29/18, WL threshold: 4096, image sequence number: 1283732989

[ 1.885031] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40

[ 1.894247] UBI: background thread "ubi_bgt0d" started, PID 1080

[ 1.894253] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

[ 1.898215] ALSA device list:

[ 1.898219] No soundcards found.

[ 1.914597] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082

[ 1.943584] UBIFS: recovery needed

[ 2.010216] UBIFS: recovery completed

[ 2.013882] UBIFS: mounted UBI device 0, volume 0, name "rootfs"

[ 2.019832] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[ 2.028938] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)

[ 2.038827] UBIFS: reserved for root: 0 bytes (0 KiB)

[ 2.043857] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model

[ 2.055416] VFS: Mounted root (ubifs filesystem) on device 0:11.

[ 2.062842] devtmpfs: mounted

[ 2.065948] Freeing unused kernel memory: 204K (c06d2000 - c0705000)

[ 2.902139] random: dd urandom read with 0 bits of entropy available

[ 3.316845]

[ 3.316845] bcm54xx_config_init

[ 3.926835]

[ 3.926835] bcm54xx_config_init

[ 28.927669] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz

[ 28.933763] xemacps e000b000.ps7-ethernet: link up (100/FULL)

[ 47.214665] In axi fpga driver!

[ 47.217778] request_mem_region OK!

[ 47.221130] AXI fpga dev virtual address is 0xdf9fc000

[ 47.226235] *base_vir_addr = 0x8c510

[ 47.241738] In fpga mem driver!

[ 47.244810] request_mem_region OK!

[ 47.248433] fpga mem virtual address is 0xe2000000

[ 48.046830]

[ 48.046830] bcm54xx_config_init

[ 48.676834]

[ 48.676834] bcm54xx_config_init

[ 51.677679] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz

[ 51.683699] xemacps e000b000.ps7-ethernet: link up (100/FULL)

[ 439.996842] random: nonblocking pool is initialized

This is XILINX board. Totalram: 507527168

Detect 512MB control board of XILINX

DETECT HW version=0008c510

miner ID : 8144cc2815408814

Miner Type = S9

AsicType = 1387

real AsicNum = 63

use critical mode to search freq...

get PLUG ON=0x000000e0

Find hashboard on Chain[5]

Find hashboard on Chain[6]

Find hashboard on Chain[7]

set_reset_allhashboard = 0x0000ffff

Check chain[5] PIC fw version=0x03

Check chain[6] PIC fw version=0x03

Check chain[7] PIC fw version=0x03

chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

has freq in PIC, will disable freq setting.

chain[5] has freq in PIC and will jump over...

Chain[5] has core num in PIC

Chain[5] ASIC[1] has core num=2

Chain[5] ASIC[4] has core num=4

Chain[5] ASIC[6] has core num=3

Chain[5] ASIC[14] has core num=1

Chain[5] ASIC[15] has core num=1

Chain[5] ASIC[16] has core num=15

Chain[5] ASIC[19] has core num=1

Chain[5] ASIC[32] has core num=3

Chain[5] ASIC[39] has core num=1

Chain[5] ASIC[58] has core num=15

Chain[5] ASIC[60] has core num=15

Check chain[5] PIC fw version=0x03

chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

has freq in PIC, will disable freq setting.

chain[6] has freq in PIC and will jump over...

Chain[6] has core num in PIC

Chain[6] ASIC[5] has core num=2

Chain[6] ASIC[9] has core num=7

Chain[6] ASIC[14] has core num=15

Chain[6] ASIC[23] has core num=4

Chain[6] ASIC[46] has core num=15

Chain[6] ASIC[47] has core num=3

Check chain[6] PIC fw version=0x03

chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

has freq in PIC, will disable freq setting.

chain[7] has freq in PIC and will jump over...

Chain[7] has core num in PIC

Chain[7] ASIC[12] has core num=1

Check chain[7] PIC fw version=0x03

get PIC voltage=91 on chain[5], value=890

get PIC voltage=91 on chain[6], value=890

get PIC voltage=91 on chain[7], value=890

set_reset_allhashboard = 0x00000000

chain[5] temp offset record: 62,-77,0,0,0,0,33,0

chain[5] temp chip I2C addr=0x98

chain[6] temp offset record: 62,-104,0,0,0,0,33,0

chain[6] temp chip I2C addr=0x98

chain[7] temp offset record: 62,-83,0,0,0,0,33,0

chain[7] temp chip I2C addr=0x98

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

CRC error counter=0

set command mode to VIL

--- check asic number

After Get ASIC NUM CRC error counter=0

set_baud=0

The min freq=700

set real timeout 52, need sleep=379392

After TEST CRC error counter=0

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

search freq for 1 times, completed chain = 3, total chain num = 3

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

restart Miner chance num=2

waiting for receive_func to exit!

waiting for pic heart to exit!

bmminer not found=20462 root 0:00 grep bmminer

bmminer not found, restart bmminer ...

bmminer not found=21156 root 0:00 grep bmminer

bmminer not found, restart bmminer ...

This is user mode for mining

Detect 512MB control board of XILINX

Miner Type = S9

Miner compile time: Fri Nov 17 17:37:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

set_reset_allhashboard = 0x0000ffff

miner ID : 8144cc2815408814

set_reset_allhashboard = 0x0000ffff

Checking fans!get fan[2] speed=4560

get fan[2] speed=4560

get fan[5] speed=6120

get fan[2] speed=4560

get fan[5] speed=6120

get fan[2] speed=4560

get fan[5] speed=6120

chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

Detect: use voltage limit rules on single board!

Detect: S9_63 use voltage level=1 : 1

Chain[J6] has backup chain_voltage=870

Check chain[5] PIC fw version=0x03

chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

Detect: use voltage limit rules on single board!

Detect: S9_63 use voltage level=1 : 1

Chain[J7] has backup chain_voltage=890

Check chain[6] PIC fw version=0x03

chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

Detect: use voltage limit rules on single board!

Detect: S9_63 use voltage level=1 : 1

Chain[J8] has backup chain_voltage=890

Check chain[7] PIC fw version=0x03

Chain[J6] orignal chain_voltage_pic=125 value=870

Chain[J7] orignal chain_voltage_pic=91 value=890

Chain[J8] orignal chain_voltage_pic=91 value=890

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

Chain[J6] has 63 asic

Chain[J7] has 2 asic

set_reset_hashboard = 0x00000040

set_reset_hashboard = 0x00000000

retry Chain[J7] has 2 asic

set_reset_hashboard = 0x00000040

set_reset_hashboard = 0x00000000

retry Chain[J7] has 2 asic

set_reset_hashboard = 0x00000040

set_reset_hashboard = 0x00000000

retry Chain[J7] has 2 asic

set_reset_hashboard = 0x00000040

set_reset_hashboard = 0x00000000

retry Chain[J7] has 2 asic

set_reset_hashboard = 0x00000040

set_reset_hashboard = 0x00000000

retry Chain[J7] has 2 asic

set_reset_hashboard = 0x00000040

set_reset_hashboard = 0x00000000

retry Chain[J7] has 2 asic

Chain[J8] has 63 asic

Chain[J6] has core num in PIC

Chain[J6] ASIC[1] has core num=2

Chain[J6] ASIC[4] has core num=4

Chain[J6] ASIC[6] has core num=3

Chain[J6] ASIC[14] has core num=1

Chain[J6] ASIC[15] has core num=1

Chain[J6] ASIC[16] has core num=15

Chain[J6] ASIC[19] has core num=1

Chain[J6] ASIC[32] has core num=3

Chain[J6] ASIC[39] has core num=1

Chain[J6] ASIC[58] has core num=15

Chain[J6] ASIC[60] has core num=15

Chain[J7] has core num in PIC

Chain[J7] ASIC[5] has core num=2

Chain[J7] ASIC[9] has core num=7

Chain[J7] ASIC[14] has core num=15

Chain[J7] ASIC[23] has core num=4

Chain[J7] ASIC[46] has core num=15

Chain[J7] ASIC[47] has core num=3

Chain[J8] has core num in PIC

Chain[J8] ASIC[12] has core num=1

miner total rate=13728GH/s fixed rate=13500GH/s

read PIC voltage=940 on chain[5]

Chain:5 chipnum=63

Chain[J6] voltage added=0.0V

Chain:5 temp offset=-77

Chain:5 base freq=687

Asic[ 0]:687

Asic[ 1]:687 Asic[ 2]:687 Asic[ 3]:687 Asic[ 4]:687 Asic[ 5]:687 Asic[ 6]:687 Asic[ 7]:687 Asic[ 8]:687

Asic[ 9]:687 Asic[10]:687 Asic[11]:687 Asic[12]:687 Asic[13]:687 Asic[14]:687 Asic[15]:687 Asic[16]:687

Asic[17]:687 Asic[18]:687 Asic[19]:687 Asic[20]:687 Asic[21]:687 Asic[22]:687 Asic[23]:687 Asic[24]:687

Asic[25]:687 Asic[26]:687 Asic[27]:687 Asic[28]:687 Asic[29]:687 Asic[30]:687 Asic[31]:687 Asic[32]:687

Asic[33]:687 Asic[34]:687 Asic[35]:687 Asic[36]:687 Asic[37]:687 Asic[38]:687 Asic[39]:687 Asic[40]:687

Asic[41]:687 Asic[42]:687 Asic[43]:687 Asic[44]:687 Asic[45]:687 Asic[46]:687 Asic[47]:687 Asic[48]:687

Asic[49]:687 Asic[50]:687 Asic[51]:687 Asic[52]:687 Asic[53]:687 Asic[54]:687 Asic[55]:687 Asic[56]:687

Asic[57]:687 Asic[58]:687 Asic[59]:687 Asic[60]:687 Asic[61]:687 Asic[62]:687

Chain:5 max freq=687

Chain:5 min freq=687

read PIC voltage=940 on chain[6]

Chain:6 chipnum=2

Chain[J7] voltage added=0.0V

Chain:6 temp offset=-104

Chain:6 base freq=650

Asic[ 0]:650

Asic[ 1]:650

Chain:6 max freq=650

Chain:6 min freq=650

read PIC voltage=940 on chain[7]

Chain:7 chipnum=63

Chain[J8] voltage added=0.0V

Chain:7 temp offset=-83

Chain:7 base freq=631

Asic[ 0]:631

Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631

Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631

Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631

Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631

Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631

Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631

Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631

Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631

Chain:7 max freq=631

Chain:7 min freq=631

Miner fix freq ...

read PIC voltage=940 on chain[5]

Chain:5 chipnum=63

Chain[J6] voltage added=0.0V

Chain:5 temp offset=-77

Chain:5 base freq=687

Asic[ 0]:687

Asic[ 1]:687 Asic[ 2]:687 Asic[ 3]:687 Asic[ 4]:687 Asic[ 5]:687 Asic[ 6]:687 Asic[ 7]:687 Asic[ 8]:687

Asic[ 9]:687 Asic[10]:687 Asic[11]:687 Asic[12]:687 Asic[13]:687 Asic[14]:687 Asic[15]:687 Detect a bad chip=16 on chain[5], fixed to 400M

Asic[16]:687

Asic[17]:687 Asic[18]:687 Asic[19]:687 Asic[20]:687 Asic[21]:687 Asic[22]:687 Asic[23]:687 Asic[24]:687

Asic[25]:687 Asic[26]:687 Asic[27]:687 Asic[28]:687 Asic[29]:687 Asic[30]:687 Asic[31]:687 Asic[32]:687

Asic[33]:687 Asic[34]:687 Asic[35]:687 Asic[36]:687 Asic[37]:687 Asic[38]:687 Asic[39]:687 Asic[40]:687

Asic[41]:687 Asic[42]:687 Asic[43]:687 Asic[44]:687 Asic[45]:687 Asic[46]:687 Asic[47]:687 Asic[48]:687

Asic[49]:687 Asic[50]:687 Asic[51]:687 Asic[52]:687 Asic[53]:687 Asic[54]:687 Asic[55]:687 Asic[56]:687

Asic[57]:687 Detect a bad chip=58 on chain[5], fixed to 400M

Asic[58]:687 Asic[59]:687 Detect a bad chip=60 on chain[5], fixed to 400M

Asic[60]:687 Asic[61]:687 Asic[62]:687