Jump to content
Lexis77

Antminer. Все модели. Вопросы, помощь, обсуждение.

Recommended Posts

Столкнулся со следующей проблемой. Асик S9 показывает 15 грудусов постоянно. Хшрейт 0.

Ниже лог

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-g16220c3 ([email protected]) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06da8ac   (6987 kB)
[    0.000000]       .init : 0xc06db000 - 0xc070e380   ( 205 kB)
[    0.000000]       .data : 0xc0710000 - 0xc0757138   ( 285 kB)
[    0.000000]        .bss : 0xc0757144 - 0xc0797bfc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]     Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000297] ps7-ttc #0 at df804000, irq=43
[    0.000597] Console: colour dummy device 80x30
[    0.000626] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.090244] pid_max: default: 32768 minimum: 301
[    0.090451] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090471] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092632] CPU: Testing write buffer coherency: ok
[    0.092943] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.092999] Setting up static identity map for 0x4cb118 - 0x4cb170
[    0.093220] L310 cache controller enabled
[    0.093240] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.170991] CPU1: Booted secondary processor
[    0.260221] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.260349] Brought up 2 CPUs
[    0.260368] SMP: Total of 2 processors activated.
[    0.260376] CPU: All CPU(s) started in SVC mode.
[    0.261036] devtmpfs: initialized
[    0.263461] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.264649] regulator-dummy: no parameters
[    0.271994] NET: Registered protocol family 16
[    0.274259] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.276520] cpuidle: using governor ladder
[    0.276533] cpuidle: using governor menu
[    0.283849] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.285364] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.285377] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.285487] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.307082] bio: create slab <bio-0> at 0
[    0.308472] vgaarb: loaded
[    0.309167] SCSI subsystem initialized
[    0.310050] usbcore: registered new interface driver usbfs
[    0.310262] usbcore: registered new interface driver hub
[    0.310486] usbcore: registered new device driver usb
[    0.311008] media: Linux media interface: v0.10
[    0.311296] Linux video capture interface: v2.00
[    0.311545] pps_core: LinuxPPS API ver. 1 registered
[    0.311557] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.311685] PTP clock support registered
[    0.312043] EDAC MC: Ver: 3.0.0
[    0.313225] Advanced Linux Sound Architecture Driver Initialized.
[    0.315948] DMA-API: preallocated 4096 debug entries
[    0.315961] DMA-API: debugging enabled by kernel config
[    0.316032] Switched to clocksource arm_global_timer
[    0.336871] NET: Registered protocol family 2
[    0.337527] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.337584] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.337669] TCP: Hash tables configured (established 4096 bind 4096)
[    0.337712] TCP: reno registered
[    0.337729] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.337759] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.337992] NET: Registered protocol family 1
[    0.338325] RPC: Registered named UNIX socket transport module.
[    0.338337] RPC: Registered udp transport module.
[    0.338346] RPC: Registered tcp transport module.
[    0.338354] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.338366] PCI: CLS 0 bytes, default 64
[    0.338791] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.340767] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.342830] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.343028] msgmni has been set to 967
[    0.343775] io scheduler noop registered
[    0.343788] io scheduler deadline registered
[    0.343833] io scheduler cfq registered (default)
[    0.356461] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.356481] dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.479693] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.046921] console [ttyPS0] enabled
[    1.051167] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.058791] [drm] Initialized drm 1.1.0 20060810
[    1.075691] brd: module loaded
[    1.085056] loop: module loaded
[    1.094427] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.100398] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.108237] libphy: XEMACPS mii bus: probed
[    1.112604] ------------- phy_id = 0x3625e62
[    1.117548] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.126176] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.132793] ehci-pci: EHCI PCI platform driver
[    1.140028] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.146844] usbcore: registered new interface driver usb-storage
[    1.153670] mousedev: PS/2 mouse device common for all mice
[    1.159771] i2c /dev entries driver
[    1.166686] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.172165] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.178091] Xilinx Zynq CpuIdle Driver started
[    1.182940] sdhci: Secure Digital Host Controller Interface driver
[    1.189120] sdhci: Copyright(c) Pierre Ossman
[    1.193388] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.200210] mmc0: no vqmmc regulator found
[    1.204224] mmc0: no vmmc regulator found
[    1.246052] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.254747] usbcore: registered new interface driver usbhid
[    1.260257] usbhid: USB HID core driver
[    1.264952] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.271252] nand: Micron MT29F2G08ABAEAWP
[    1.275218] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.281161] Bad block table found at page 131008, version 0x01
[    1.287388] Bad block table found at page 130944, version 0x01
[    1.293436] 3 ofpart partitions found on MTD device pl353-nand
[    1.299217] Creating 3 MTD partitions on "pl353-nand":
[    1.304308] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.312369] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.319694] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.330410] TCP: cubic registered
[    1.333643] NET: Registered protocol family 17
[    1.338338] Registering SWP/SWPB emulation handler
[    1.344202] regulator-dummy: disabling
[    1.348510] UBI: attaching mtd1 to ubi0
[    1.875647] UBI: scanning is finished
[    1.887301] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.894353] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.901149] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.907825] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.914663] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.920673] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.927784] UBI: max/mean erase counter: 18/11, WL threshold: 4096, image sequence number: 934887695
[    1.936902] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.946117] UBI: background thread "ubi_bgt0d" started, PID 1084
[    1.946123] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.950015] ALSA device list:
[    1.950018]   No soundcards found.
[    1.966438] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[    1.995426] UBIFS: recovery needed
[    2.396617] UBIFS: recovery completed
[    2.400298] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.406242] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.415339] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.425242] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.430280] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2F0368C9-A3D5-4F6F-8350-C0A1080F2C3F, small LPT model
[    2.441559] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.448737] devtmpfs: mounted
[    2.451836] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[    3.297378] random: dd urandom read with 1 bits of entropy available
[    3.676080] 
[    3.676080] bcm54xx_config_init
[    4.286046] 
[    4.286046] bcm54xx_config_init
[    9.286915] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    9.293021] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   23.352022] In axi fpga driver!
[   23.355088] request_mem_region OK!
[   23.358513] AXI fpga dev virtual address is 0xdf9fe000
[   23.363587] *base_vir_addr = 0xc51e
[   23.378583] In fpga mem driver!
[   23.381650] request_mem_region OK!
[   23.385212] fpga mem virtual address is 0xe2000000
[   24.175451] 
[   24.175451] bcm54xx_config_init
[   24.805389] 
[   24.805389] bcm54xx_config_init
[   28.805855] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   28.811870] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  188.377073] random: nonblocking pool is initialized
log_level = 4
This is XILINX board. Totalram:       507486208
Detect 512MB control board of XILINX
mmap axi_fpga_addr = 0xb6f29000
axi_fpga_addr data = 0xc51e
mmap fpga_mem_addr = 0xb5d22000
forceFreq=-1 forceFlag=0
min work minertest[0]:912


DETECT HW version=0000c51e
miner ID : 810c45425c208814
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x00000080
Find hashboard on Chain[7]
Check chain[7] PIC fw version=0x03
read pic freq and badcore num...
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[6] has core num=1
Chain[7] ASIC[7] has core num=1
Chain[7] ASIC[20] has core num=1
Chain[7] ASIC[31] has core num=3
Chain[7] ASIC[32] has core num=1
Chain[7] ASIC[47] has core num=1
Chain[7] ASIC[52] has core num=1
Chain[7] ASIC[54] has core num=10
Chain[7] ASIC[56] has core num=3
Chain[7] ASIC[60] has core num=2
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[7], value=870
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
total_exist_chain_num = 1
single_board_frq_tuning enter
min_rate, des_rate, fix_volt:13800, 14000, 880
force_freq not set, don't need tuning
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found=12985 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Wed Nov 7 11:19:02 CST 2018 type: Antminer S9i
miner ID : 810c45425c208814
Checking fans...
get fan[4] speed=5520
get fan[4] speed=5520
get fan[5] speed=6120
get fan[4] speed=5520
get fan[5] speed=6120
get fan[4] speed=5520
get fan[5] speed=6120
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
last_freq: 0x00 0x7d 0x00 0x4b 0x00 0x4b 0x04 0x4b 0x0b 0x4b 0x00 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x03 0x4b 0x01 0x4b 0x01 0x4b 0x0f 0x4b 0x0f 0x4b 0x0f 0x4b 0x0f 0x4b 0x05 0x4b 0x07 0x4b 0x23 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 0x00 0x4b 
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=870
No scan based on domain
Check chain[7] PIC fw version=0x03
total_exist_chain_num = 1
Chain[J8] orignal chain_voltage_pic=125 value=870
Chain[J8] has 63 asic
Chain[J8] has core num in PIC
Chain[J8] ASIC[6] has core num=1
Chain[J8] ASIC[7] has core num=1
Chain[J8] ASIC[20] has core num=1
Chain[J8] ASIC[31] has core num=3
Chain[J8] ASIC[32] has core num=1
Chain[J8] ASIC[47] has core num=1
Chain[J8] ASIC[52] has core num=1
Chain[J8] ASIC[54] has core num=10
Chain[J8] ASIC[56] has core num=3
Chain[J8] ASIC[60] has core num=2
miner total rate=4695GH/s ideal_total_hash_rate = 4500GH/s
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=656
Asic[ 0]:656 Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 
Asic[ 8]:656 Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 
Asic[16]:656 Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 
Asic[24]:656 Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 
Asic[32]:656 Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 
Asic[40]:656 Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 
Asic[48]:656 Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 
Asic[56]:656 Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656 
Chain:7 max freq=656
Chain:7 min freq=656


Miner fix freq ...
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=656
Asic[ 0]:656 Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 
Asic[ 8]:656 Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 
Asic[16]:656 Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 
Asic[24]:656 Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 
Asic[32]:656 Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 
Asic[40]:656 Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 
Asic[48]:656 Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 
Asic[56]:656 Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656 
Chain:7 max freq=656
Chain:7 min freq=656

max freq = 656
totalRate = 4695, fixed_totalRate = 4500
set baud=1
Chain[J8] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[8] chip[244] local:29 remote:32 offset:27 
Chain[J8] chip[244] get middle temp offset=27 typeID=55
setting to working voltage...
chain[7] set voltage to 930
chain[7] set voltage to 920
chain[7] set voltage to 910
chain[7] set voltage to 900
chain[7] set voltage to 890
chain[7] set voltage to 880
chain[7] set voltage to 870
start thread for read temp
setStartTimePoint total_tv_start_sys=270 total_tv_end_sys=271
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000 
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
read failed on Chain[7] Chip[62] middle Temp old value:0
Special fix Chain[7] Chip[62] middle Temp = 15
Done read temp on Chain[7]
Max pcb temp : 0
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=8

По логам понял только что скорость вентиляторов установлено на 100%  

Share this post


Link to post
Share on other sites
14 часов назад, Milena Antselevich сказал:

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000 
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Check Chain[J8] ASIC RT error: (asic index start from 1-63)

Хеш плату в ремонт.

Share this post


Link to post
Share on other sites
7 минут назад, warlenix сказал:

Хеш плату в ремонт.

я бы так и сделал, но рядом нет никакого ремонта, и отправлять куда то кому то непонятному не сильно хочется. 

Share this post


Link to post
Share on other sites
13 минут назад, Milena Antselevich сказал:

я бы так и сделал, но рядом нет никакого ремонта, и отправлять куда то кому то непонятному не сильно хочется. 

Тогда на полку положите, сами вы ситуацию исправить не сможете

 

Share this post


Link to post
Share on other sites

@Milena Antselevich  в мириг отправьте и не бойтесь..

Share this post


Link to post
Share on other sites

У меня мириг отказались менять чип из за сложности , а асикфокс взялся обойти сложное место на плате и запустить без этого чипа .

Share this post


Link to post
Share on other sites

Вот и я про то же, не нужно бояться, обращайтесь к проверенным.

Share this post


Link to post
Share on other sites

Народ подскажите пжста в чем проблема? s11

 

Скрытый текст

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty ([email protected]) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 199144K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30232K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17192K (cca37000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 579/397, WL threshold: 4096, image sequence number: 1648065480
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID E21330DC-7D20-4955-ACB9-65B40F087009, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 658217607
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 97883A21-F447-4ED1-A20A-A87BF2EA3FF3, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
main.c:13999: log_level = 4
main.c:14026: This is XILINX board. Totalram:       239353856
main.c:14044: Detect 256MB control board of XILINX
driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6f01000
driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d
driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5d05000
driver-bitmain.c:995: forceFreq=-1 forceFlag=0
driver-bitmain.c:1697: min work minertest[0]:912


main.c:8490: DETECT HW version=000ab00d
main.c:14071: miner ID : 815c0d242b104814
main.c:14100: Miner Type = S9+
main.c:14108: AsicType = 1387
main.c:14111: real AsicNum = 84
main.c:14204: use critical mode to search freq...
driver-bitmain.c:1877: get PLUG ON=0x00000007
driver-bitmain.c:1947: Find hashboard on Chain[0]
driver-bitmain.c:1947: Find hashboard on Chain[1]
driver-bitmain.c:1947: Find hashboard on Chain[2]
main.c:2148: chain[0] PIC jump to app
main.c:2153: Check chain[0] PIC fw version=0xa4
main.c:2148: chain[1] PIC jump to app
main.c:2153: Check chain[1] PIC fw version=0xa4
main.c:2148: chain[2] PIC jump to app
main.c:2153: Check chain[2] PIC fw version=0xa4
main.c:8805: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0xfb 0x19 0x00 0x00 0xc8 0xfe 0xee 0xbf 0xfb 0xbe 0xfb 0xfe 0xbe 0xfb 0xbe 0xbf 0xbf 0xfe 0xfb 0xbe 0xaf 0xef 0xef 0xef 0xeb 0xef 0x4c 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8817: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[0] has freq in PIC and will jump over...
main.c:8999: Chain[0] has core num in PIC
main.c:8805: Chain[1] read_freq_badcores : 0x7d 0xd9 0x5a 0x4e 0x56 0x4e 0x5a 0x56 0x4e 0x56 0x5a 0x56 0x5a 0x4e 0x4e 0x56 0x5a 0x5a 0x4e 0x56 0x5a 0x4e 0x56 0x5a 0x56 0x4e 0x56 0x5a 0x4e 0x5a 0x4e 0x56 0x4e 0x5a 0x56 0x5a 0x4e 0x56 0x56 0x5a 0x4e 0x4e 0x56 0x5a 0x5a 0x56 0x4e 0x56 0x5a 0x4e 0x5a 0x56 0x4e 0x5a 0x56 0x4e 0x4e 0x56 0x5a 0x4e 0x56 0x5a 0x56 0x5a 0x4e 0x56 0x5a 0x4e 0x5a 0x4e 0x56 0x5a 0x4e 0x56 0x4e 0x5a 0x56 0x5a 0x4e 0x56 0x56 0x5a 0x4e 0x4e 0x56 0x5a 0x43 0x1a 0x00 0x00 0xc8 0xfd 0xfd 0xdd 0x5f 0xdf 0xf7 0x77 0x7f 0xf7 0xf7 0xd7 0xdf 0x7d 0xff 0x7d 0xfd 0xdd 0xf7 0x77 0x7f 0xf7 0x5e 0x12 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8817: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[1] has freq in PIC and will jump over...
main.c:8999: Chain[1] has core num in PIC
main.c:8805: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0xe0 0x19 0x00 0x00 0xc8 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xd4 0x0f 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
main.c:8817: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[2] has freq in PIC and will jump over...
main.c:8999: Chain[2] has core num in PIC
main.c:9103: get PIC voltage=0 on chain[0], value=930
main.c:9103: get PIC voltage=0 on chain[1], value=930
main.c:9103: get PIC voltage=0 on chain[2], value=930
main.c:9269: chain[0] temp offset record: 24,0,45,0,0,0,35,28
main.c:9286: chain[0] temp chip I2C addr=0x98
main.c:9292: chain[0] has no middle temp, use special fix mode.
main.c:9269: chain[1] temp offset record: 24,0,45,0,0,0,37,28
main.c:9286: chain[1] temp chip I2C addr=0x98
main.c:9292: chain[1] has no middle temp, use special fix mode.
main.c:9269: chain[2] temp offset record: 24,0,45,0,0,0,37,28
main.c:9286: chain[2] temp chip I2C addr=0x98
main.c:9292: chain[2] has no middle temp, use special fix mode.
main.c:13963: total_exist_chain_num = 3
main.c:14645: restart Miner chance num=0
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13934: bmminer not found= 1095 root      2156 S    grep bmminer

main.c:14743: bmminer not found, restart bmminer ...
driver-btm-c5.c:12241:bitmain_c5_init: This is the first time running after searching freq!
driver-btm-c5.c:12301:bitmain_c5_init: Detect 256MB control board of XILINX
driver-btm-c5.c:12320:bitmain_c5_init: Miner Type = S9+
driver-btm-c5.c:12327:bitmain_c5_init: Miner compile time: Tue Mar 19 14:29:33 CST 2019 type: Antminer S11
driver-btm-c5.c:12407:bitmain_c5_init: miner ID : 815c0d242b104814
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=1560
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=1560
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=1560
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:12564:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5280
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5280
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5280
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5280
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5280
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5280
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5280
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5280
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3024:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3024:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3024:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3024:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3024:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=5400
driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=5400
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[0] PIC fw version=0xa4
driver-btm-c5.c:13017:bitmain_c5_init: Chain[0] read_freq_badcores : 0x7d 0xd9 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0xfb 0x19 0x00 0x00 0xc8 0xfe 0xee 0xbf 0xfb 0xbe 0xfb 0xfe 0xbe 0xfb 0xbe 0xbf 0xbf 0xfe 0xfb 0xbe 0xaf 0xef 0xef 0xef 0xeb 0xef 0x4c 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
driver-btm-c5.c:13056:bitmain_c5_init: Chain[J1] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13067:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13071:bitmain_c5_init: S9+ fix Chain[J1] test patten OK temp=60
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[1] PIC fw version=0xa4
driver-btm-c5.c:13017:bitmain_c5_init: Chain[1] read_freq_badcores : 0x7d 0xd9 0x5a 0x4e 0x56 0x4e 0x5a 0x56 0x4e 0x56 0x5a 0x56 0x5a 0x4e 0x4e 0x56 0x5a 0x5a 0x4e 0x56 0x5a 0x4e 0x56 0x5a 0x56 0x4e 0x56 0x5a 0x4e 0x5a 0x4e 0x56 0x4e 0x5a 0x56 0x5a 0x4e 0x56 0x56 0x5a 0x4e 0x4e 0x56 0x5a 0x5a 0x56 0x4e 0x56 0x5a 0x4e 0x5a 0x56 0x4e 0x5a 0x56 0x4e 0x4e 0x56 0x5a 0x4e 0x56 0x5a 0x56 0x5a 0x4e 0x56 0x5a 0x4e 0x5a 0x4e 0x56 0x5a 0x4e 0x56 0x4e 0x5a 0x56 0x5a 0x4e 0x56 0x56 0x5a 0x4e 0x4e 0x56 0x5a 0x43 0x1a 0x00 0x00 0xc8 0xfd 0xfd 0xdd 0x5f 0xdf 0xf7 0x77 0x7f 0xf7 0xf7 0xd7 0xdf 0x7d 0xff 0x7d 0xfd 0xdd 0xf7 0x77 0x7f 0xf7 0x5e 0x12 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
driver-btm-c5.c:13056:bitmain_c5_init: Chain[J2] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13067:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13071:bitmain_c5_init: S9+ fix Chain[J2] test patten OK temp=60
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[2] PIC fw version=0xa4
driver-btm-c5.c:13017:bitmain_c5_init: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x56 0x4e 0x56 0x4e 0x56 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x4e 0x4e 0x56 0x56 0x56 0x4e 0x56 0x56 0x56 0x4e 0xe0 0x19 0x00 0x00 0xc8 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xd4 0x0f 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 
driver-btm-c5.c:13056:bitmain_c5_init: Chain[J3] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13067:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13071:bitmain_c5_init: S9+ fix Chain[J3] test patten OK temp=60
driver-btm-c5.c:12200:init_exist_chain_table: total_exist_chain_num = 3
power.c:148:power_check_protocal_type: power protocal f5, using package cmd
power.c:173:power_type_detect: start detect power type
power.c:181:power_type_detect: init gpio907
power.c:211:power_type_detect: power type is APW8 new type
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 0.000000
power.c:587:get_min_voltage: board[2] voltage: 0.000000
power.c:587:get_min_voltage: board[0] voltage: 0.000000
power.c:593:get_min_voltage: min voltage: 0.000000
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:629:set_iic_power_voltage: power voltage abnormal
driver-btm-c5.c:12205:stop_mining: power abnormal
 

 

понимаю, что питании, но не до конца ((((

Share this post


Link to post
Share on other sites

Господа, заранее прошу прошение за то, что забанили в гугле...
Довольно давно майню на Сигме. С их кастомной прошивкой. Прошивка хорошая, без девфри, с автотюном, стабильная и простая. Но самому пулу в последнее время как-то плоховато. В общем я решил от них уходить.

Кто какие прошивки использует?
1)Главное без "противооткатного" антивируса.
2)Без девфри.

Share this post


Link to post
Share on other sites

@Halavshk а чем родная не устраивает, которая последняя от 18 года? Несколько глючных машин она у меня живила.

Кстати, есть у меня один асик с багом, из-за плохого инета на нем платы теряются по одной и помогает только розетка. Но на днях случился фатал, пропали все три платы, а розетку дернуть нет возможности. Даже перепрошивка не помогла. Ну фиг с ним, потом как нить человек будет и дернет. А тут бац - одна плата сама появилась, через пару дней вторая... прям колдунство :) Думаю подожду еще пару дней и третья сама вернется.

Share this post


Link to post
Share on other sites

Хех. Судя по скорости, пару часов назад заработала третья плата )))

Share this post


Link to post
Share on other sites

Шаманов в предках не было? 😄

Ребуты силой мысли, повышение хешрейта по фотографии. Ваша фамилия не Кашпировский? 

--

а по делу на S11 альтернативных прошивок не кто не видел?

 

Share this post


Link to post
Share on other sites

Ребят, есть инфа, можно ли каким-то образом посмотреть на с9-ых температуру одного конкретного чипа?

Share this post


Link to post
Share on other sites

@MadMarx Нет, это физически невозможно.

Хотя если подумать, есть же тепловизор. Но в естественных условиях (внутри корпуса), естественно ничего не увидишь.

Edited by Splinter

Share this post


Link to post
Share on other sites

Всем привет!

Нужен совет. Есть Antminer S9 13.5. Сгорел блок питания "муравей" на 1800 Вт. Заменены транзистор и кондей. После подключения к Асику происходит следующая ситуация: загрузка идет больше чем обычно, после продувки и загрузки красные светодиоды на хеш платах гаснут и не горят. В интерфейсе показывает температуру -49 на всех 3-х платах. Производительность фактически нулевая. После эксперементов с включением - отключением плат показало, что в нормальном режиме работают максимально 2 платы в любой последовательности. Запосного Асика или БП для проверки нет. Все в одном экземпляре. Прошу совета куда копать. Логи работы и скрины на 3 и 2-х платах прилагаю.

P.S. Замеры напряжения на клеммах питания плат:

12,11 – сразу после включения
11,35 – с 1-ой картой в работе
10,16 – с 2-мя картами в работе
9,10 – с 3-мя картами в работе

3 карты.jpg

6 и 7 карта.jpg

Overview.jpg

3 карты Log.txt 6 и 7 карта Log.txt

8-я карта.jpg

8-я карта Log.txt

Edited by Bambula

Share this post


Link to post
Share on other sites

@Bambula Плохо починили БП, не тянет он. Чините или меняйте БП. При нагрузке в 1500Вт муравей проседает примерно до 11.8-11.9В (при холостых 12.2В), а у вас 9,1В.

Edited by Splinter

Share this post


Link to post
Share on other sites
13 минут назад, Splinter сказал:

@Bambula Плохо починили БП, не тянет он. Чините или меняйте БП. При нагрузке в 1500Вт муравей проседает примерно до 11.8-11.9В (при холостых 12.2В), а у вас 9,1В.

Спасибо.

Попробуем еще раз проверить БП. 9V тоже показалось маловато поэтому и решил посоветоваться на форуме.

Share this post


Link to post
Share on other sites
16.09.2019 в 01:53, [email protected] сказал:

Шаманов в предках не было? 😄

Ребуты силой мысли, повышение хешрейта по фотографии. Ваша фамилия не Кашпировский? 

--

а по делу на S11 альтернативных прошивок не кто не видел?

 

не видел, но у меня проблема решилась ремонтом бп

Share this post


Link to post
Share on other sites

Ребят помогите, что случилось, красные диоды не горят на платах

л4.png

л1.png

л2.png

л6.png

л7.png

л8.png

л3.png

л5.png

Share this post


Link to post
Share on other sites

@1122 

не вижу в логе второго вентилятора

Share this post


Link to post
Share on other sites
3 часа назад, adv сказал:

@1122 

не вижу в логе второго вентилятора

Спс, это под замену

 

Share this post


Link to post
Share on other sites

Приветствую!

Помогите четвертый день с платами (8) вожусь, ревизия 4.21 изначально на них было 0 асик, на некоторых с питанием беда, исправил все чипы по тестеру частоту держат без отклонений все тестпоинты в норме, но температуру не видит раз 5 уже 62 чип поменял без толку, там два датчика температуры, первый раз с такой проблемой столкнулся, но форуме читал, но все очень размыто, может есть у кого прошивка чтобы перешить на один температурный датчик. Вообщем помогите пожалуйста!!!!

Share this post


Link to post
Share on other sites

Всем Привет.

Помогите идентифицировать элемент... по маркировке ничего не могу найти в сети WD7PC. Стоит на плате Antminera E3.

 

1.jpg

Share this post


Link to post
Share on other sites

У меня тут вот какое чудо появилось :biggrin:

2019-09-28_22-18-32.png

Share this post


Link to post
Share on other sites

@scopus Средняя плата обрела второе дыхание перед халвингом, не хочет на свалку.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Topics

    • НОВИЧКИ Bits.Media, все сюда!

      Обновлено 15 марта 2017 Всем привет. Если вы зашли в эту тему значит либо вы еще не в "теме", либо в теме но хотите узнать что-то новое. Возможно вы услышали про биток в одной из многочисленных новостей или с форумов. А может даже пришли с грабительского Рублика. Этой темой я хочу разрешить регулярные вопросы, которые рано или поздно возникают у всех кто решил влится в тему заработка на криптовалютах. Я не буду останавливаться на технических подробностях, и потому что сам не до конца понимаю раб

      in Общие вопросы по майнингу

    • [MinerStats Lite] - Бесплатный Мониторинг Асиков Antminer

      MinerStats Lite Бесплатное программное обеспечение, которое предназначено для осуществления полного контроля работы ваших майнеров.  Текущая версия MSLite запускается на Windows-x64, Linux-x64. По запросу софт доступен для Linux-armv6, Linux-armv7.  Программа поддерживает все типы асиков компании Bitmain - Antmainer S9, S9i, S9j, T9+, L3+, D3, S17/pro и другие. _____________________________________________________   Возможности MSLite: 1. Статистика.  Отображение д

      in Мониторинг

    • Ремонт Antminer S7, S9 (обмен опытом)

      Официальный сайт | Antminer. Все модели. Вопросы, помощь, обсуждение.   В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы.   Статьи на bits.media:   Полезное:   (!) FAQ (часто задаваемые вопросы)   -Как найти в продаже разъемы питания, какая маркиров

      in ASIC/FPGA майнеры

    • Bitmain анонсировали новые модели майнеров Antminer S17+ и Antminer T17+

      Вчера на мероприятии World Digital Mining Summit сооснователь Bitmain Цзихань У анонсировал новые модели ASIC-майнеров серии S17 с увеличенным количеством чипов - Antminer S17+ и Antminer T17+.   «Новые майнеры стали более производительными и энергоэффективными. Хэшрейт Antminer S17+ равен 73 Тх/с, а показатель энергоэффективности равен 40 Дж/Тх плюс-минус 10%. У Antminer T17+ хэшрейт равен 64 Тх/с, а энергоэффективность 50 Дж/Тх + 10%», - написано в блоге компании Bitmain.

      in Новости криптовалют

    • Alipay будет блокировать все транзакции, связанные с торговлей криптовалютами

      Платежное подразделение компании Alibaba – Alipay – сообщило, что будет блокировать все транзакции, связанные с торговлей биткоином и прочими криптовалютами. Таким образом компания в очередной раз отметила крайне негативное отношение к криптовалютам. Alipay добавила, что внимательно наблюдает за внебиржевой торговлей и не позволит осуществлять деятельность, которая нарушает действующие законы и правила.   Отметим, что за день до этого биржа Binance запустила P2P-сервис,

      in Новости криптовалют

×
×
  • Create New...