Ремонт: Antminer s17/t17

[dirtygarryluga]

Ребя, всем привет. Вопрос есть обрыв цепи. Плата запускается только после отключения её проверки. Все 30 чипов находит но не стартует. Как этот долбаный обрыв найти? 

[cleaner1]

@alex59 Приветствую, помогите разобраться пожалуйста с Т17 , на последнем домене не проходят сигналы CLK и  RI. нет питания по линиям 0,8 и 1,7 на чипах в этом домене, это если на тестере мерить,соответственно не видит не один чип, а если подцепить питание напрямую минуя ключи то эти напряжения присутствуют на всём последнем домене, на стабилизатор напряжения который из 5v делает 0,8v для последнего домена приходит всего 1,5v это в режиме теста, если на прямую цеплять то 2,7v. на рабочей плате от 5 до 10v на неё обычно приходит, я так понимаю что в этом проблема, почему маленькое напряжение там? подскажите.Чипы в домене естественно заменил, все микрухи которые его питают тоже и даже пик махнул,результат тот же, что я упустил?

 

[alex59]

А бустер выдает повышенное? 

[alex59]

и я что то несовсем понял, у Вас на ключах силовых падает напряжение сильно? (если есть разница через ключи или напрямую)

[cleaner1]

вот так в режиме тестера, если подать напряжение на прямую, минуя ключи то там где 1,5в становиться 2,7в и CLK и RI на последнем домене поднимаются

[cleaner1]

я так понимаю регулятор напряжения 1517dr должен выдавать 5в, дальше из 5в микруха с маркировкой sxe1839 делает 0,8в но этого в режиме тестера не происходит, если напрямую то всё есть,

Изменено 10 авг 2022, 04:01 пользователем cleaner1

[alex59]

У вас не работает повышающий преобразователь на микросхеме MP1517DR - U7 (далее Бустер) 

в бустере (микросхема U7), отсутствует выходной (бустерный) конденсатор 47мкф@50в обозначен краской на плате EC26 (Без него вряд ли будет корректно работать), на его плюсе относительно минуса источника питания (ну или на резисторе 0 ом) должно быть повышенное напряжение, (при 18,8 с БП на нем будет порядка 22-23 вольт. относительно минусового провода с БП)
кроме того рядом с U7 мелкий кондер снесли, верните его наместо. промойте это место хорошенько, там достаточно высокоомные резисторы в обратной связи стоят.

Изменено 9 авг 2022, 10:14 пользователем alex59

[cleaner1]

ec26 я снял чтобы не греть его сильно при замене всего что рядом, с ним или без него всё то же самое, маленькую керамику я сдвинул чтоб проверить, он так же не влияет ни на что, что с ним что без него, весь этот узел был перекинут с рабочей платы, а перекинутые компоненты с нерабочей платы отлично работают на другой, как то так, вот и в ступоре(

[cleaner1]

3 часа назад, alex59 сказал:

на его плюсе относительно минуса источника питания (ну или на резисторе 0 ом) должно быть повышенное напряжение, (при 18,8 с БП на нем будет порядка 22-23 вольт. относительно минусового провода с БП

да, на рабочей плате так и есть а на этой 16,5в

 

конденсатор 47мкф@50 и мелкую керамику заменил сейчас ещё раз с рабочей платы, результат ноль, 16,5в выдаёт и всё тут

Изменено 9 авг 2022, 13:42 пользователем cleaner1

[alex59]

Проверьте напряжение на 4 выводе, должно быть не менее 1,5В

Проверьте напряжение на 16 выводе, должно быть менее 0,7 вольт. если там больше, то виноваты резисторы обратной связи.

делитель дает Uвх(выв8)*(10/325) вольт при НЕРАБОТАЮЩЕМ бустере. при нормальном бустере будет 0,7

*Все измерения относительно земли U7

*Проверьте бустерный диод. 

*если напруга на выв. 16 выше 0,7 пошевелите R2001 он на стороне BOT резистор 300К, под ним могли образоваться "вискеры", оловянные усы. (было у меня такое, похожы на серый налет)

Изменено 9 авг 2022, 13:55 пользователем alex59

[cleaner1]

на 4 выводе 2,0в

на 16 выводе 0,75в

D4 и L4 ранее были заменены

Изменено 9 авг 2022, 14:11 пользователем cleaner1

[alex59]

9 минут назад, cleaner1 сказал:

на 4 выводе 2,0в

на 16 выводе 0,75в

D4 и L4 ранее были заменены

проверяйте резисторы R83, R2000? R2001 должно быть меньшее напряжение 16,5/32,5=0,508В на 16 выводе, промойте если там "грязно"...0,75>0.7 = шим 1517 заблокирован

Изменено 9 авг 2022, 14:20 пользователем alex59

[cleaner1]

да- уж, дело было в R2001. поменял его и плата ожила, хотя в этом месте тоже всё  проверял, сравнивал с рабочей, будем знать теперь, Спасибо тебе добрый человек!

[alex59]

3 минуты назад, cleaner1 сказал:

да- уж, дело было в R2001. поменял его и плата ожила, хотя в этом месте тоже всё  проверял, сравнивал с рабочей, будем знать теперь, Спасибо тебе добрый человек!

можно было просто демонтировать, почистить под ним и запаять наместо...:) скорее всего, это то о чем я говорил выше. сам с этой бедой пол дня сидел в первый раз.

Изменено 9 авг 2022, 14:53 пользователем alex59

[cleaner1]

1 минуту назад, alex59 сказал:

можно было просто демонтировать, почистить под ним и запаять наместо...:) скорее всего, это то о чем я говорил выше. сам с этой бедой пол дня сидел в первый раз.

а я второй день мучаюсь)), самое интересное ведь замерял сопротивление на всех них, никакой аномалии не было, да и сейчас перед заменой тоже замерял, вроде всё то же, а поменял и заработало, вот же собака серая)

[alex59]

Да этот делитель не продуман разработчиком, зачем использовать высокоомные резисторы непонятно, можно было в 10 раз меньшие номиналы взять, 1,5к вместо 15к, 1к вместо 10к, и 30к вместо 300к. и все работало бы стабильней. 300К в схеме не дает промерять, приходится смотреть только результат деления напряжения этого делителя.  

[cleaner1]

4 часа назад, alex59 сказал:

Да этот делитель не продуман разработчиком, зачем использовать высокоомные резисторы непонятно, можно было в 10 раз меньшие номиналы взять, 1,5к вместо 15к, 1к вместо 10к, и 30к вместо 300к. и все работало бы стабильней. 300К в схеме не дает промерять, приходится смотреть только результат деления напряжения этого делителя.  

таки дохлый оказался резюк, 200к и уже не работает бустер

[Мишаня1]

В 31.03.2022 в 06:33, 425624 сказал:

Всём добрый день. Подскажите пожалуйста, кто сталкивался. После запуска чудо аппарата т17, через некоторое время зелёная лампочка загорается, но мощность написано 0th. Куда копать? Логи приложил, скрин тоже. Заранее спасибо. 

 

  Показать контент

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203752K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25624K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12584K (cceb7000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 2579122177
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 85D84F26-1C71-4F38-B7D3-FE5BA6AD41D2, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1673/375, WL threshold: 4096, image sequence number: 3389548455
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 721E72E7-F382-4130-AD9F-6C10D9102537, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
Mar 30 20:03:21 (none) local0.notice bmminer: set_start_time_point total_tv_start_sys=1635 total_tv_end_sys=1636
Mar 30 20:03:24 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_api_detect return: 0
Mar 30 20:03:25 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_update_job return: 0
Mar 30 20:03:25 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_shutdown return: 0
Mar 30 20:03:25 (none) local0.err cgminer: Miner compile time: Thu Apr 23 16:29:07 CST 2020 type: Antminer T17
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: about to send detect
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: set_start_time_point total_tv_start_sys=1639 total_tv_end_sys=1640
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Probing for an alive pool
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: LOW POWER MODE!
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Switching to pool 1 stratum+tcp://sha256.poolbinance.com:443 - first alive pool
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: in stratum_sthread 
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Pool 1 difficulty changed to 131072
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: LOW POWER MODE!
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: in stratum_sthread 
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Pool 2 difficulty changed to 131072
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Network diff set to 27.5T
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: LOW POWER MODE!
Mar 30 20:03:25 (none) local0.warn cgminer[5457]: Pool 0 stratum+tcp://bs.poolbinance.com:3333 alive, testing stability
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: in stratum_sthread 
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Pool 0 difficulty changed to 131072
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: POOL 1 support ab mode!
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: POOL 0 support ab mode!
Mar 30 20:03:26 (none) local0.notice cgminer[5457]: update job
Mar 30 20:03:26 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:03:26 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:03:26 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:03:26 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:03:26 (none) local0.warn cgminer[5457]: Pool 0 stratum+tcp://bs.poolbinance.com:3333 stable for >120 seconds
Mar 30 20:03:26 (none) local0.warn cgminer[5457]: Switching to pool 0 stratum+tcp://bs.poolbinance.com:3333
Mar 30 20:03:30 (none) local0.notice cgminer[5457]: update job
Mar 30 20:03:30 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:03:30 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:03:30 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:03:30 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:03:31 (none) local0.warn cgminer[5457]: API running in IP access mode on port 4028 (14)
Mar 30 20:04:02 (none) local0.notice cgminer[5457]: update job
Mar 30 20:04:02 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:04:02 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:04:02 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:04:02 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:04:32 (none) local0.notice cgminer[5457]: update job
Mar 30 20:04:32 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:04:32 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:04:32 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:04:32 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:05:02 (none) local0.notice cgminer[5457]: update job
Mar 30 20:05:02 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:05:02 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:05:02 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:05:02 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:05:32 (none) local0.notice cgminer[5457]: update job
Mar 30 20:05:32 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:05:32 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:05:32 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:05:32 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:06:06 (none) local0.notice cgminer[5457]: update job
Mar 30 20:06:06 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:06:06 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:06:06 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:06:06 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:06:36 (none) local0.notice cgminer[5457]: update job
Mar 30 20:06:36 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:06:36 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:06:36 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:06:36 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:06:39 (none) local0.notice cgminer[5457]: Stratum from pool 0 detected new block at height 729735
Mar 30 20:06:39 (none) local0.notice cgminer[5457]: update job
Mar 30 20:06:39 (none) local0.notice cgminer[5457]: job buf total len:2206, offset:2206
Mar 30 20:06:39 (none) local0.notice cgminer[5457]: about to send job, size is 2206
Mar 30 20:06:39 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2206
Mar 30 20:06:39 (none) local0.notice bmminer: parse job buf len:2206
Mar 30 20:06:40 (none) local0.notice cgminer[5457]: update job
Mar 30 20:06:40 (none) local0.notice cgminer[5457]: job buf total len:2591, offset:2591
Mar 30 20:06:40 (none) local0.notice cgminer[5457]: about to send job, size is 2591
Mar 30 20:06:40 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2591
Mar 30 20:06:40 (none) local0.notice bmminer: parse job buf len:2591
Mar 30 20:07:10 (none) local0.notice cgminer[5457]: update job
Mar 30 20:07:10 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:07:10 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:07:10 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:07:10 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:07:42 (none) local0.notice cgminer[5457]: update job
Mar 30 20:07:42 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:07:42 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:07:42 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:07:42 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:08:12 (none) local0.notice cgminer[5457]: update job
Mar 30 20:08:12 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:08:12 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:08:12 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:08:12 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:08:40 (none) local0.notice cgminer[5457]: update job
Mar 30 20:08:40 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:08:40 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:08:40 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:08:40 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:09:12 (none) local0.notice cgminer[5457]: update job
Mar 30 20:09:12 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:09:12 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:09:12 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:09:12 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:09:42 (none) local0.notice cgminer[5457]: update job
Mar 30 20:09:42 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:09:42 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:09:42 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:09:42 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:10:14 (none) local0.notice cgminer[5457]: update job
Mar 30 20:10:14 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:10:14 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:10:14 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:10:14 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:10:46 (none) local0.notice cgminer[5457]: update job
Mar 30 20:10:46 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:10:46 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:10:46 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:10:46 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:11:20 (none) local0.notice cgminer[5457]: update job
Mar 30 20:11:20 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:11:20 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:11:20 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:11:20 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:11:42 (none) local0.notice cgminer[5457]: update job
Mar 30 20:11:42 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:11:42 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:11:42 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:11:42 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:12:12 (none) local0.notice cgminer[5457]: update job
Mar 30 20:12:12 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:12:12 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:12:12 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:12:12 (none) local0.notice bmminer: parse job buf len:2590
2022-03-30 19:57:22 driver-btm-api.c:663:init_freq_mode: This is scan-user version
2022-03-30 19:57:22 driver-btm-api.c:2028:bitmain_soc_init: opt_multi_version     = 1
2022-03-30 19:57:22 driver-btm-api.c:2029:bitmain_soc_init: opt_bitmain_ab        = 1
2022-03-30 19:57:22 driver-btm-api.c:2030:bitmain_soc_init: opt_bitmain_work_mode = 0
2022-03-30 19:57:22 driver-btm-api.c:2031:bitmain_soc_init: Miner compile time: Thu Apr 23 16:29:07 CST 2020 type: Antminer T17
2022-03-30 19:57:22 driver-btm-api.c:2032:bitmain_soc_init: commit version: 1c5be6f 2020-04-20 16:18:14, build by: lol 2020-04-23 16:35:04
2022-03-30 19:57:22 driver-btm-api.c:1844:show_sn: no SN got, please write SN to /nvdata/sn
2022-03-30 19:57:22 driver-btm-api.c:1167:miner_device_init: Detect 256MB control board of XILINX
2022-03-30 19:57:22 driver-btm-api.c:1115:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2022-03-30 19:57:22 thread.c:885:create_read_nonce_reg_thread: create thread
2022-03-30 19:57:28 driver-btm-api.c:1099:init_miner_version: miner ID : 812cf4025c208854
2022-03-30 19:57:28 driver-btm-api.c:1105:init_miner_version: FPGA Version = 0xB013
2022-03-30 19:57:30 eeprom.c:456:check_pattern_test_level: L6 board
2022-03-30 19:57:32 eeprom.c:456:check_pattern_test_level: L6 board
2022-03-30 19:57:33 eeprom.c:456:check_pattern_test_level: L6 board
2022-03-30 19:57:33 eeprom.c:545:eeprom_load: try higher voltage open core
2022-03-30 19:57:33 driver-btm-api.c:737:get_product_id: product_id[0] = 1
2022-03-30 19:57:33 driver-btm-api.c:737:get_product_id: product_id[1] = 1
2022-03-30 19:57:33 driver-btm-api.c:737:get_product_id: product_id[2] = 1
2022-03-30 19:57:33 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[0] = 1
2022-03-30 19:57:33 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[1] = 1
2022-03-30 19:57:33 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[2] = 1
2022-03-30 19:57:33 driver-btm-api.c:1919:bitmain_board_init: g_ccdly_opt = 1
2022-03-30 19:57:33 driver-btm-api.c:676:_set_project_type: project:2
2022-03-30 19:57:33 driver-btm-api.c:706:_set_project_type: Project type: Antminer T17
2022-03-30 19:57:33 driver-btm-api.c:717:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:718:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:717:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:718:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:717:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:718:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2022-03-30 19:57:35 driver-btm-api.c:1939:bitmain_board_init: Fan check passed.
2022-03-30 19:57:37 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2022-03-30 19:57:41 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2022-03-30 19:57:42 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2022-03-30 19:57:46 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2022-03-30 19:57:48 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2022-03-30 19:57:51 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2022-03-30 19:57:51 thread.c:880:create_pic_heart_beat_thread: create thread
2022-03-30 19:57:51 power_api.c:55:power_init: power init ... 
2022-03-30 19:57:51 driver-btm-api.c:1949:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2022-03-30 19:58:23 power_api.c:264:set_iic_power_to_custom_voltage: setting to voltage: 18.00 ...
2022-03-30 19:58:29 power_api.c:124:check_voltage_multi: retry time: 0
2022-03-30 19:58:31 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.179326 
2022-03-30 19:58:32 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.277295 
2022-03-30 19:58:34 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.314033 
2022-03-30 19:58:34 power_api.c:97:get_average_voltage: aveage voltage is: 18.256885 
2022-03-30 19:58:34 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 18.000000 
2022-03-30 19:58:34 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2022-03-30 19:58:46 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2022-03-30 19:58:55 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2022-03-30 19:59:06 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2022-03-30 19:59:09 driver-btm-api.c:352:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0xff
2022-03-30 19:59:09 driver-btm-api.c:352:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0xff
2022-03-30 19:59:10 driver-btm-api.c:352:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0xff
2022-03-30 19:59:10 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0xb4
2022-03-30 19:59:10 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2022-03-30 19:59:10 driver-btm-api.c:1693:check_clock_counter: freq 50 clock_counter_limit 6
2022-03-30 19:59:10 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2022-03-30 19:59:10 voltage[0] = 1690
2022-03-30 19:59:10 voltage[1] = 1690
2022-03-30 19:59:10 voltage[2] = 1690
2022-03-30 19:59:10 power_api.c:140:set_working_voltage: working_voltage = 16.900000
2022-03-30 19:59:12 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2022-03-30 19:59:13 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2022-03-30 19:59:15 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2022-03-30 19:59:15 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2022-03-30 19:59:16 driver-btm-api.c:252:check_bringup_temp: Bring up temperature is 28
2022-03-30 19:59:16 thread.c:900:create_check_miner_status_thread: create thread
2022-03-30 19:59:16 thread.c:890:create_set_miner_status_thread: create thread
2022-03-30 19:59:16 driver-btm-api.c:613:calculate_timeout: dev->timeout = 392
2022-03-30 19:59:16 thread.c:875:create_temperature_monitor_thread: create thread
2022-03-30 19:59:16 freq_tuning.c:159:freq_tuning_get_max_freq: Max freq of tuning is 760
2022-03-30 19:59:16 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.60 ...
2022-03-30 19:59:41 power_api.c:124:check_voltage_multi: retry time: 0
2022-03-30 19:59:44 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.756836 
2022-03-30 19:59:47 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.860928 
2022-03-30 19:59:51 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.928281 
2022-03-30 19:59:51 power_api.c:97:get_average_voltage: aveage voltage is: 17.848681 
2022-03-30 20:02:06 thread.c:734:check_temperature: over max temp, pcb temp 59 (max 80), chip temp 104(max 103)
2022-03-30 20:02:06 driver-btm-api.c:205:set_miner_status: ERROR_TEMP_TOO_HIGH
2022-03-30 20:02:06 driver-btm-api.c:146:stop_mining: stop mining: over max temp
2022-03-30 20:02:06 thread.c:920:cancel_temperature_monitor_thread: cancel thread
2022-03-30 20:02:06 thread.c:930:cancel_read_nonce_reg_thread: cancel thread
2022-03-30 20:02:06 driver-btm-api.c:131:killall_hashboard: ****power off hashboard****
2022-03-30 20:02:39 driver-btm-api.c:644:set_timeout: freq 720 final timeout=163
2022-03-30 20:02:39 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2022-03-30 20:03:03 power_api.c:124:check_voltage_multi: retry time: 0
2022-03-30 20:03:07 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.787451 
2022-03-30 20:03:10 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.879297 
2022-03-30 20:03:13 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.934404 
2022-03-30 20:03:13 power_api.c:97:get_average_voltage: aveage voltage is: 17.867051 
2022-03-30 20:03:13 frequency.c:654:get_current_min_freq: current min freq 720
2022-03-30 20:03:13 driver-btm-api.c:1693:check_clock_counter: freq 720 clock_counter_limit 92
2022-03-30 20:03:16 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 5, core = 0, found 0, clock counter 0x00000000
2022-03-30 20:03:16 driver-btm-api.c:2139:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.
2022-03-30 20:03:16 thread.c:895:create_check_system_status_thread: create thread
2022-03-30 20:03:16 driver-btm-api.c:2155:bitmain_soc_init: Init done!
2022-03-30 20:03:16 driver-btm-api.c:205:set_miner_status: STATUS_INIT
2022-03-30 20:03:21 driver-btm-api.c:205:set_miner_status: STATUS_OKAY
2022-03-30 20:03:26 driver-btm-api.c:1325:dhash_chip_send_job: Version num 4

Температура высокая у чипа вот и отключается

[Мишаня1]

В 09.08.2022 в 14:34, cleaner1 сказал:

вот так в режиме тестера, если подать напряжение на прямую, минуя ключи то там где 1,5в становиться 2,7в и CLK и RI на последнем домене поднимаются

Можно вопрос не в тему? На какую термопрокладку радиаторы посажены?

[cleaner1]

4 часа назад, Мишаня1 сказал:

Можно вопрос не в тему? На какую термопрокладку радиаторы посажены?

У меня на пасту, розовую китайцы с радиаторами её отправляют

Изменено 11 авг 2022, 16:24 пользователем cleaner1

[нет огненных глаз]

On 3/31/2022 at 9:33 AM, 425624 said:

Всём добрый день. Подскажите пожалуйста, кто сталкивался. После запуска чудо аппарата т17, через некоторое время зелёная лампочка загорается, но мощность написано 0th. Куда копать? Логи приложил, скрин тоже. Заранее спасибо. 

 

  Reveal hidden contents

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203752K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25624K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12584K (cceb7000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 2579122177
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 85D84F26-1C71-4F38-B7D3-FE5BA6AD41D2, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1673/375, WL threshold: 4096, image sequence number: 3389548455
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 721E72E7-F382-4130-AD9F-6C10D9102537, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
Mar 30 20:03:21 (none) local0.notice bmminer: set_start_time_point total_tv_start_sys=1635 total_tv_end_sys=1636
Mar 30 20:03:24 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_api_detect return: 0
Mar 30 20:03:25 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_update_job return: 0
Mar 30 20:03:25 (none) local0.notice cgminer: cgminer_socket_init reg bitmain_shutdown return: 0
Mar 30 20:03:25 (none) local0.err cgminer: Miner compile time: Thu Apr 23 16:29:07 CST 2020 type: Antminer T17
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: about to send detect
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: set_start_time_point total_tv_start_sys=1639 total_tv_end_sys=1640
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Probing for an alive pool
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: LOW POWER MODE!
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Switching to pool 1 stratum+tcp://sha256.poolbinance.com:443 - first alive pool
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: in stratum_sthread 
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Pool 1 difficulty changed to 131072
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: LOW POWER MODE!
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: in stratum_sthread 
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Pool 2 difficulty changed to 131072
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Network diff set to 27.5T
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: LOW POWER MODE!
Mar 30 20:03:25 (none) local0.warn cgminer[5457]: Pool 0 stratum+tcp://bs.poolbinance.com:3333 alive, testing stability
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: in stratum_sthread 
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: Pool 0 difficulty changed to 131072
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: POOL 1 support ab mode!
Mar 30 20:03:25 (none) local0.notice cgminer[5457]: POOL 0 support ab mode!
Mar 30 20:03:26 (none) local0.notice cgminer[5457]: update job
Mar 30 20:03:26 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:03:26 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:03:26 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:03:26 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:03:26 (none) local0.warn cgminer[5457]: Pool 0 stratum+tcp://bs.poolbinance.com:3333 stable for >120 seconds
Mar 30 20:03:26 (none) local0.warn cgminer[5457]: Switching to pool 0 stratum+tcp://bs.poolbinance.com:3333
Mar 30 20:03:30 (none) local0.notice cgminer[5457]: update job
Mar 30 20:03:30 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:03:30 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:03:30 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:03:30 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:03:31 (none) local0.warn cgminer[5457]: API running in IP access mode on port 4028 (14)
Mar 30 20:04:02 (none) local0.notice cgminer[5457]: update job
Mar 30 20:04:02 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:04:02 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:04:02 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:04:02 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:04:32 (none) local0.notice cgminer[5457]: update job
Mar 30 20:04:32 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:04:32 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:04:32 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:04:32 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:05:02 (none) local0.notice cgminer[5457]: update job
Mar 30 20:05:02 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:05:02 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:05:02 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:05:02 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:05:32 (none) local0.notice cgminer[5457]: update job
Mar 30 20:05:32 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:05:32 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:05:32 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:05:32 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:06:06 (none) local0.notice cgminer[5457]: update job
Mar 30 20:06:06 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:06:06 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:06:06 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:06:06 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:06:36 (none) local0.notice cgminer[5457]: update job
Mar 30 20:06:36 (none) local0.notice cgminer[5457]: job buf total len:2558, offset:2558
Mar 30 20:06:36 (none) local0.notice cgminer[5457]: about to send job, size is 2558
Mar 30 20:06:36 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2558
Mar 30 20:06:36 (none) local0.notice bmminer: parse job buf len:2558
Mar 30 20:06:39 (none) local0.notice cgminer[5457]: Stratum from pool 0 detected new block at height 729735
Mar 30 20:06:39 (none) local0.notice cgminer[5457]: update job
Mar 30 20:06:39 (none) local0.notice cgminer[5457]: job buf total len:2206, offset:2206
Mar 30 20:06:39 (none) local0.notice cgminer[5457]: about to send job, size is 2206
Mar 30 20:06:39 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2206
Mar 30 20:06:39 (none) local0.notice bmminer: parse job buf len:2206
Mar 30 20:06:40 (none) local0.notice cgminer[5457]: update job
Mar 30 20:06:40 (none) local0.notice cgminer[5457]: job buf total len:2591, offset:2591
Mar 30 20:06:40 (none) local0.notice cgminer[5457]: about to send job, size is 2591
Mar 30 20:06:40 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2591
Mar 30 20:06:40 (none) local0.notice bmminer: parse job buf len:2591
Mar 30 20:07:10 (none) local0.notice cgminer[5457]: update job
Mar 30 20:07:10 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:07:10 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:07:10 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:07:10 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:07:42 (none) local0.notice cgminer[5457]: update job
Mar 30 20:07:42 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:07:42 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:07:42 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:07:42 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:08:12 (none) local0.notice cgminer[5457]: update job
Mar 30 20:08:12 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:08:12 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:08:12 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:08:12 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:08:40 (none) local0.notice cgminer[5457]: update job
Mar 30 20:08:40 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:08:40 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:08:40 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:08:40 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:09:12 (none) local0.notice cgminer[5457]: update job
Mar 30 20:09:12 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:09:12 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:09:12 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:09:12 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:09:42 (none) local0.notice cgminer[5457]: update job
Mar 30 20:09:42 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:09:42 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:09:42 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:09:42 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:10:14 (none) local0.notice cgminer[5457]: update job
Mar 30 20:10:14 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:10:14 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:10:14 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:10:14 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:10:46 (none) local0.notice cgminer[5457]: update job
Mar 30 20:10:46 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:10:46 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:10:46 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:10:46 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:11:20 (none) local0.notice cgminer[5457]: update job
Mar 30 20:11:20 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:11:20 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:11:20 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:11:20 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:11:42 (none) local0.notice cgminer[5457]: update job
Mar 30 20:11:42 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:11:42 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:11:42 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:11:42 (none) local0.notice bmminer: parse job buf len:2590
Mar 30 20:12:12 (none) local0.notice cgminer[5457]: update job
Mar 30 20:12:12 (none) local0.notice cgminer[5457]: job buf total len:2590, offset:2590
Mar 30 20:12:12 (none) local0.notice cgminer[5457]: about to send job, size is 2590
Mar 30 20:12:12 (none) local0.notice bmminer: bitmain_update_job_cb, rec job data 0xb4800528 size: 2590
Mar 30 20:12:12 (none) local0.notice bmminer: parse job buf len:2590
2022-03-30 19:57:22 driver-btm-api.c:663:init_freq_mode: This is scan-user version
2022-03-30 19:57:22 driver-btm-api.c:2028:bitmain_soc_init: opt_multi_version     = 1
2022-03-30 19:57:22 driver-btm-api.c:2029:bitmain_soc_init: opt_bitmain_ab        = 1
2022-03-30 19:57:22 driver-btm-api.c:2030:bitmain_soc_init: opt_bitmain_work_mode = 0
2022-03-30 19:57:22 driver-btm-api.c:2031:bitmain_soc_init: Miner compile time: Thu Apr 23 16:29:07 CST 2020 type: Antminer T17
2022-03-30 19:57:22 driver-btm-api.c:2032:bitmain_soc_init: commit version: 1c5be6f 2020-04-20 16:18:14, build by: lol 2020-04-23 16:35:04
2022-03-30 19:57:22 driver-btm-api.c:1844:show_sn: no SN got, please write SN to /nvdata/sn
2022-03-30 19:57:22 driver-btm-api.c:1167:miner_device_init: Detect 256MB control board of XILINX
2022-03-30 19:57:22 driver-btm-api.c:1115:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2022-03-30 19:57:22 thread.c:885:create_read_nonce_reg_thread: create thread
2022-03-30 19:57:28 driver-btm-api.c:1099:init_miner_version: miner ID : 812cf4025c208854
2022-03-30 19:57:28 driver-btm-api.c:1105:init_miner_version: FPGA Version = 0xB013
2022-03-30 19:57:30 eeprom.c:456:check_pattern_test_level: L6 board
2022-03-30 19:57:32 eeprom.c:456:check_pattern_test_level: L6 board
2022-03-30 19:57:33 eeprom.c:456:check_pattern_test_level: L6 board
2022-03-30 19:57:33 eeprom.c:545:eeprom_load: try higher voltage open core
2022-03-30 19:57:33 driver-btm-api.c:737:get_product_id: product_id[0] = 1
2022-03-30 19:57:33 driver-btm-api.c:737:get_product_id: product_id[1] = 1
2022-03-30 19:57:33 driver-btm-api.c:737:get_product_id: product_id[2] = 1
2022-03-30 19:57:33 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[0] = 1
2022-03-30 19:57:33 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[1] = 1
2022-03-30 19:57:33 driver-btm-api.c:1666:get_ccdly_opt: ccdly_opt[2] = 1
2022-03-30 19:57:33 driver-btm-api.c:1919:bitmain_board_init: g_ccdly_opt = 1
2022-03-30 19:57:33 driver-btm-api.c:676:_set_project_type: project:2
2022-03-30 19:57:33 driver-btm-api.c:706:_set_project_type: Project type: Antminer T17
2022-03-30 19:57:33 driver-btm-api.c:717:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:718:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:717:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:718:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:717:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2022-03-30 19:57:33 driver-btm-api.c:718:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2022-03-30 19:57:35 driver-btm-api.c:1939:bitmain_board_init: Fan check passed.
2022-03-30 19:57:37 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2022-03-30 19:57:41 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2022-03-30 19:57:42 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2022-03-30 19:57:46 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2022-03-30 19:57:48 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2022-03-30 19:57:51 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2022-03-30 19:57:51 thread.c:880:create_pic_heart_beat_thread: create thread
2022-03-30 19:57:51 power_api.c:55:power_init: power init ... 
2022-03-30 19:57:51 driver-btm-api.c:1949:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2022-03-30 19:58:23 power_api.c:264:set_iic_power_to_custom_voltage: setting to voltage: 18.00 ...
2022-03-30 19:58:29 power_api.c:124:check_voltage_multi: retry time: 0
2022-03-30 19:58:31 power_api.c:86:get_average_voltage: chain[0], voltage is: 18.179326 
2022-03-30 19:58:32 power_api.c:86:get_average_voltage: chain[1], voltage is: 18.277295 
2022-03-30 19:58:34 power_api.c:86:get_average_voltage: chain[2], voltage is: 18.314033 
2022-03-30 19:58:34 power_api.c:97:get_average_voltage: aveage voltage is: 18.256885 
2022-03-30 19:58:34 power_api.c:182:set_iic_power_by_voltage: now set voltage to : 18.000000 
2022-03-30 19:58:34 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2022-03-30 19:58:46 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[0]: find 30 asic, times 0
2022-03-30 19:58:55 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[1]: find 30 asic, times 0
2022-03-30 19:59:06 driver-btm-api.c:1042:check_asic_number_with_power_on: Chain[2]: find 30 asic, times 0
2022-03-30 19:59:09 driver-btm-api.c:352:set_order_clock: chain[0]: set order clock, stragegy 3 clock_en=0xff
2022-03-30 19:59:09 driver-btm-api.c:352:set_order_clock: chain[1]: set order clock, stragegy 3 clock_en=0xff
2022-03-30 19:59:10 driver-btm-api.c:352:set_order_clock: chain[2]: set order clock, stragegy 3 clock_en=0xff
2022-03-30 19:59:10 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0xb4
2022-03-30 19:59:10 uart.c:80:set_baud: set fpga_baud = 3000000, fpga_divider = 0
2022-03-30 19:59:10 driver-btm-api.c:1693:check_clock_counter: freq 50 clock_counter_limit 6
2022-03-30 19:59:10 uart.c:80:set_baud: set fpga_baud = 115200, fpga_divider = 26
2022-03-30 19:59:10 voltage[0] = 1690
2022-03-30 19:59:10 voltage[1] = 1690
2022-03-30 19:59:10 voltage[2] = 1690
2022-03-30 19:59:10 power_api.c:140:set_working_voltage: working_voltage = 16.900000
2022-03-30 19:59:12 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2022-03-30 19:59:13 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2022-03-30 19:59:15 temperature.c:282:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2022-03-30 19:59:15 uart.c:80:set_baud: set fpga_baud = 6000000, fpga_divider = 3
2022-03-30 19:59:16 driver-btm-api.c:252:check_bringup_temp: Bring up temperature is 28
2022-03-30 19:59:16 thread.c:900:create_check_miner_status_thread: create thread
2022-03-30 19:59:16 thread.c:890:create_set_miner_status_thread: create thread
2022-03-30 19:59:16 driver-btm-api.c:613:calculate_timeout: dev->timeout = 392
2022-03-30 19:59:16 thread.c:875:create_temperature_monitor_thread: create thread
2022-03-30 19:59:16 freq_tuning.c:159:freq_tuning_get_max_freq: Max freq of tuning is 760
2022-03-30 19:59:16 power_api.c:379:slowly_set_iic_power_to_custom_voltage: slowly setting to voltage: 17.60 ...
2022-03-30 19:59:41 power_api.c:124:check_voltage_multi: retry time: 0
2022-03-30 19:59:44 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.756836 
2022-03-30 19:59:47 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.860928 
2022-03-30 19:59:51 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.928281 
2022-03-30 19:59:51 power_api.c:97:get_average_voltage: aveage voltage is: 17.848681 
2022-03-30 20:02:06 thread.c:734:check_temperature: over max temp, pcb temp 59 (max 80), chip temp 104(max 103)
2022-03-30 20:02:06 driver-btm-api.c:205:set_miner_status: ERROR_TEMP_TOO_HIGH
2022-03-30 20:02:06 driver-btm-api.c:146:stop_mining: stop mining: over max temp
2022-03-30 20:02:06 thread.c:920:cancel_temperature_monitor_thread: cancel thread
2022-03-30 20:02:06 thread.c:930:cancel_read_nonce_reg_thread: cancel thread
2022-03-30 20:02:06 driver-btm-api.c:131:killall_hashboard: ****power off hashboard****
2022-03-30 20:02:39 driver-btm-api.c:644:set_timeout: freq 720 final timeout=163
2022-03-30 20:02:39 power_api.c:397:slowly_set_iic_power_to_working_voltage: slowly setting to voltage: 16.90 ...
2022-03-30 20:03:03 power_api.c:124:check_voltage_multi: retry time: 0
2022-03-30 20:03:07 power_api.c:86:get_average_voltage: chain[0], voltage is: 17.787451 
2022-03-30 20:03:10 power_api.c:86:get_average_voltage: chain[1], voltage is: 17.879297 
2022-03-30 20:03:13 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.934404 
2022-03-30 20:03:13 power_api.c:97:get_average_voltage: aveage voltage is: 17.867051 
2022-03-30 20:03:13 frequency.c:654:get_current_min_freq: current min freq 720
2022-03-30 20:03:13 driver-btm-api.c:1693:check_clock_counter: freq 720 clock_counter_limit 92
2022-03-30 20:03:16 register.c:1416:quick_dump_core_hash_clock_counter: bad clock counter. chain = 0, asic = 5, core = 0, found 0, clock counter 0x00000000
2022-03-30 20:03:16 driver-btm-api.c:2139:bitmain_soc_init: clock count check failed after retry, wait for hash rate protect later.
2022-03-30 20:03:16 thread.c:895:create_check_system_status_thread: create thread
2022-03-30 20:03:16 driver-btm-api.c:2155:bitmain_soc_init: Init done!
2022-03-30 20:03:16 driver-btm-api.c:205:set_miner_status: STATUS_INIT
2022-03-30 20:03:21 driver-btm-api.c:205:set_miner_status: STATUS_OKAY
2022-03-30 20:03:26 driver-btm-api.c:1325:dhash_chip_send_job: Version num 4

Похоже температура чипа завышена, у Т17 температура хэш-платы превышает 104 градуса, и Т17 перестанет работать. Нужно почистить майнер от пыли и проверить, работает ли вентилятор и не болтается ли радиатор на хеш-плате. И проверьте журнал ядра на наличие других сбоев.

[Farman]

всем привет. не как не могу найти проблему, почему не ведет датчики температур.

перепропаял все 4 чипа 7.9.22.24  не ведет и все тут.

так же есть плата которая ругается на 64 чип. вопрос от куда 64 если на плате всего 30.

 

[нет огненных глаз]

4 hours ago, Farman said:

всем привет. не как не могу найти проблему, почему не ведет датчики температур.

перепропаял все 4 чипа 7.9.22.24  не ведет и все тут.

так же есть плата которая ругается на 64 чип. вопрос от куда 64 если на плате всего 30.

 

Вы проверили чип PIC этой хеш-платы? Или обновить прошивку платы управления.

[MihailLBH]

Добрый день всем. Подскажите в чем может быть проблема и как найти и что проверять.

На последнем домене нет сигнала CLK и на последнем ldo нет 0,8в, соответственно нет прихода на 28-29-30 чип и обратного RO.

По красным меткам все хорошо ldo 0,8 и 1,8 выдает, на синим отделе тестпоинтов сигнал есть, дальше пропадает. На желтом ldo 0.

 

[alex59]

@MihailLBH почитайте выше чуток про питание последнего домена https://forum.bits.media/index.php?/topic/175758-ремонт-antminer-s17t17/&do=findComment&comment=2263172   может ваш случай, если на 30 чипе 1,8 есть, то тогда смотрите прохождение этого напряжения через все чипы в этом домене от 30 к 28 и выход с 28 чипа, подается на стаб 0,8 помоему

Изменено 21 авг 2022, 13:43 пользователем alex59