Jump to content
urikedr

Antminer s17, s17+, s17e, s17pro

Recommended Posts

40 минут назад, Splinter сказал:

У меня в обслуживании много первоходок которые я обслуживанию от их рождения, и это обычное явление на полугодовалых и старше платах. Это следствие перегрева на некачественно запаянных на заводе чипах.

Да у меня тоже большую часть они составляют, еще впереди куча их, буду обращать внимание, но не заметить такое при разборе платы не реально.

40 минут назад, Splinter сказал:

лишняя возможность ободрать маску на чипе

А зачем верх перелуживать? Шило на мыло. Я чипы сажаю на свинец, а радиаторы на тот же безсвинец с висмутом (138)

Я больше имел в виду залудить площадки на плате и почистить, время отнимет но не так много, хотя сам процесс утомительный (чистки)

40 минут назад, Splinter сказал:

Учту ваш опыт, но пока останусь при своем

Да я тоже скептик и даже наверно больше хейтер когда к процессу относятся без понимания.

Если что то придет из первых, самому интересно посмотреть на состояние припоя.

Edited by Kowex

Share this post


Link to post
Share on other sites

@Kowex Интересно думаю будет Вам. (может Вы и в курсе) файлик во вложении.

сегодня был тяжелый день, хотел бы с Вами обсудить еще один большой глобальный вопрос,но думаю чуть позже.

таблица припоев.pdf

Share this post


Link to post
Share on other sites
23 часа назад, Splinter сказал:

Отчетливее это проявляется на платах где полигоны питания чипа имеют не сплошное лужение, а 'сеточкой'. Это приводит к уменьшению теплоотдачи через нижний радиатор. Больше тепла уходит в верхний

Теплопроводность меди равна 482 Вт/(м·град), припоя нашего 19 Вт/(м·град), сечения сопоставимы, думаю не в этом дело. думаю дело в разной применяемой пасте разными контрактниками.

Edited by alex59

Share this post


Link to post
Share on other sites
2 часа назад, alex59 сказал:

Теплопроводность меди равна 482 Вт/(м·град), припоя нашего 19 Вт/(м·град), сечения сопоставимы, думаю не в этом дело.

Вы кажется не уловили мысль, 'сеточка' уменьшает площадь контакта чипа с платой, сквозное меднение в которой переносит тепло в нижний радиатор. Уменьшается площадь переноса тепла, причем процентов на 40 на глаз. Возможно еще добавляется тепло на сопротивлении контакта (но тут сложно оценить). 

Похожая беда наблюдается на последних авалонах где чип лудится сеткой из шариков пасты, только там это приводит аж к прогаранию текстолита. В прочем под 30м чипом Т17 тоже часто текстолит в уголь. 

Думаю что если бы у 17 серии температура бы снималась с каждого чипа то там картина была бы просто ужасна. 

Share this post


Link to post
Share on other sites

@Splinter да, немогу понять про какую "сеточку" Вы говорите.

не про эту на чипах которая?

рис1.jpg

Edited by alex59

Share this post


Link to post
Share on other sites
15.03.2021 в 19:49, Splinter сказал:

Самый простой вариант - слетела прошивка в БП (там управляет PIC16F1704)

Всем привет. У меня похоже случился самый простой вариант, что делать плохо представляю пока, но программатор купил. Если есть у кого нибудь прошивка, скиньте пожалуйста. 

Share this post


Link to post
Share on other sites
13 часов назад, alex59 сказал:

про эту на чипах которая?

Да про этот случая. Слева прям характерно видно. Еще особенность - центр не плотно садится, здесь это тоже хорошо видно. 

Share this post


Link to post
Share on other sites
18.10.2021 в 20:23, Splinter сказал:

Отчетливее это проявляется на платах где полигоны питания чипа имеют не сплошное лужение, а 'сеточкой'. Это приводит к уменьшению теплоотдачи через нижний радиатор

Это заводской брак! причем всем бракам брак, эти ребята сэкономили везде где смогли, судя потому что и дальше такое встречаете, они продолжают давать заказы этим ребятам.

если интересно, могу все рассказать в подробностях что и как. У этих ребят, должно все было получиться,  как на лучших образцах которые Вы видели. Но они сэкономили.

А паста наносится "Сеточкой" у всех, разница в техпроцессе, у когото все как положено у кого то через одно место.

П.С.

Прошу прощения за грязную плату, это та-же самая плата. 

рис2.jpg

Edited by alex59

Share this post


Link to post
Share on other sites
7 часов назад, alex59 сказал:

если интересно, могу все рассказать в подробностях что и как.

Конечно интересно ваше видение этой проблемы.

Share this post


Link to post
Share on other sites
20.10.2021 в 23:57, a1eltsov сказал:

Всем привет. У меня похоже случился самый простой вариант, что делать плохо представляю пока, но программатор купил. Если есть у кого нибудь прошивка, скиньте пожалуйста. 

Под пикит 3, могу хекс файл скинуть на бп

Share this post


Link to post
Share on other sites

Здравствуйте. плата s17pro занижено   Vin на ldo U171 до 0.4v вместо 1.8v .  Подскажите пожалуйста откуда подаётся  это напряжение,  не могу отследить цепь.

Подозреваю где-то под радиаторами спряталась ldo, но не хочу лишний раз снимать радиаторы).

u171.jpg

Share this post


Link to post
Share on other sites

@igormigg это LDO дает 0,8 вольта. оно появится когда будет 1,8 с U252 на другой стороне платы в углу где кондеры и квадратная микросхема. 1,8 проходит с 48 чипа через 47,46,45, на это LDO 

Edited by alex59

Share this post


Link to post
Share on other sites

Большое спасибо! понятно почему не мог "отзвонить" цепь ). 

Share this post


Link to post
Share on other sites

Промеряно было без всех асиков (демонтированы) на плате, стрелка указывает на смд конденсаторы в этом месте, на них нужно смотреть наличие напруг, лень мне их рисовать было...

Цепи питания S17Pro.pdf

в квадратике источник напряжения 1,8 или 0,8

Edited by alex59

Share this post


Link to post
Share on other sites

Добрый день. Подскажите пожалуйста, может кто сталкивался. Купил s17+ 70th, вчера запустил, час проработал нормально, далее перестал видеть одну плату, работает только на двух, выдает 45-50th. Настройки сбрасывал.Что еще посоветуете? Логи приложил. 

Скрытый текст

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203432K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25944K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12904K (cce67000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 213/154, WL threshold: 4096, image sequence number: 922123630
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 6591F6B7-A8FB-4FC6-9FAA-40343961286F, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1460/195, WL threshold: 4096, image sequence number: 3814164103
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 1C567B41-1C2F-490C-BE4A-1137496C780E, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-11-22 09:18:32 driver-btm-api.c:779:init_freq_mode: This is scan-user version
2021-11-22 09:18:32 driver-btm-api.c:2451:bitmain_soc_init: opt_multi_version     = 1
2021-11-22 09:18:32 driver-btm-api.c:2452:bitmain_soc_init: opt_bitmain_ab        = 1
2021-11-22 09:18:32 driver-btm-api.c:2453:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-11-22 09:18:32 driver-btm-api.c:2454:bitmain_soc_init: Miner compile time: Tue Jun  2 10:31:07 CST 2020 type: Antminer S17+
2021-11-22 09:18:32 driver-btm-api.c:2455:bitmain_soc_init: commit version: 1ca50a5 2020-06-01 18:51:22, build by: lol 2020-06-02 10:37:21
2021-11-22 09:18:32 driver-btm-api.c:2083:show_sn: len:16, 81540d0c69208814
2021-11-22 09:18:32 driver-btm-api.c:2461:bitmain_soc_init: show sn return 1
2021-11-22 09:18:32 driver-btm-api.c:2103:handle_sn_for_factory_mode: show sn return 1
2021-11-22 09:18:32 driver-btm-api.c:2141:handle_sn_for_factory_mode: read sn success, 81540d0c69208814
2021-11-22 09:18:32 fan.c:284:front_fan_power_on: Note: front fan is power on!
2021-11-22 09:18:32 fan.c:296:rear_fan_power_on: Note: rear fan is power on!
2021-11-22 09:18:32 driver-btm-api.c:1314:miner_device_init: Detect 256MB control board of XILINX
2021-11-22 09:18:32 driver-btm-api.c:1255:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-11-22 09:18:38 driver-btm-api.c:1239:init_miner_version: miner ID : 81540d0c69208814
2021-11-22 09:18:38 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-11-22 09:18:43 driver-btm-api.c:837:get_product_id: product_id[0] = 0
2021-11-22 09:18:43 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-11-22 09:18:43 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-11-22 09:18:43 driver-btm-api.c:2234:update_conf_by_power_feedback: Power feedback is disabled
2021-11-22 09:18:43 driver-btm-api.c:2202:get_calibration_voltage: calibration voltage flag is error data.
2021-11-22 09:18:43 driver-btm-api.c:2268:update_conf_by_power_feedback: Note: no calibration voltage, default diff = 0
2021-11-22 09:18:43 frequency.c:1457:adjust_higer_max_vol_table: adjust_higer_max_vol_table, adjust_vol = 0
2021-11-22 09:18:43 thread.c:1363:create_read_nonce_reg_thread: create thread
2021-11-22 09:18:49 driver-btm-api.c:1239:init_miner_version: miner ID : 81540d0c69208814
2021-11-22 09:18:49 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-11-22 09:18:55 driver-btm-api.c:837:get_product_id: product_id[0] = 0
2021-11-22 09:18:55 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-11-22 09:18:55 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-11-22 09:18:55 driver-btm-api.c:792:_set_project_type: project:0
2021-11-22 09:18:55 driver-btm-api.c:813:_set_project_type: Project type: Antminer S17+
2021-11-22 09:18:55 driver-btm-api.c:824:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:825:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:824:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:825:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:824:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:825:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:2372:bitmain_board_init: Fan check passed.
2021-11-22 09:18:56 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-11-22 09:18:58 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88
2021-11-22 09:18:59 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-11-22 09:19:01 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2021-11-22 09:19:02 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-11-22 09:19:04 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2021-11-22 09:19:04 thread.c:1358:create_pic_heart_beat_thread: create thread
2021-11-22 09:19:04 power_api.c:213:power_init: Power init:
2021-11-22 09:19:04 power_api.c:214:power_init: current_voltage_raw = 0
2021-11-22 09:19:04 power_api.c:215:power_init: highest_voltage_raw = 2100
2021-11-22 09:19:04 power_api.c:216:power_init: working_voltage_raw = 1950
2021-11-22 09:19:04 power_api.c:217:power_init: higher_voltage_raw  = 2040
2021-11-22 09:19:04 power_api.c:218:power_init: check_asic_voltage_raw  = 2100
2021-11-22 09:19:04 driver-btm-api.c:2382:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-11-22 09:19:36 power_api.c:324:set_to_highest_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-11-22 09:20:02 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:20:03 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.127226
2021-11-22 09:20:04 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.052097
2021-11-22 09:20:05 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.183082
2021-11-22 09:20:05 power_api.c:53:_get_avg_voltage: average_voltage = 21.120802
2021-11-22 09:20:05 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.12, check voltage passed.
2021-11-22 09:20:05 uart.c:72:set_baud: set fpga_baud to 115200
2021-11-22 09:20:16 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 0
2021-11-22 09:20:27 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 1
2021-11-22 09:20:38 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 2
2021-11-22 09:20:38 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2100
chain 0, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-11-22 09:20:46 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 3
2021-11-22 09:20:46 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2050
2021-11-22 09:20:46 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2050, step by step.
2021-11-22 09:20:50 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:20:52 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.543146
2021-11-22 09:20:53 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.520966
2021-11-22 09:20:54 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.679294
2021-11-22 09:20:54 power_api.c:53:_get_avg_voltage: average_voltage = 20.581135
2021-11-22 09:20:54 power_api.c:71:check_voltage: target_vol = 20.50, actural_vol = 20.58, check voltage passed.
chain 0, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-11-22 09:21:03 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 4
2021-11-22 09:21:03 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2000
2021-11-22 09:21:03 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2000, step by step.
2021-11-22 09:21:06 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:21:07 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.060913
2021-11-22 09:21:08 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.013978
2021-11-22 09:21:09 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.199496
2021-11-22 09:21:09 power_api.c:53:_get_avg_voltage: average_voltage = 20.091462
2021-11-22 09:21:09 power_api.c:71:check_voltage: target_vol = 20.00, actural_vol = 20.09, check voltage passed.
chain 0, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-11-22 09:21:18 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 5
2021-11-22 09:21:18 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2100
2021-11-22 09:21:18 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-11-22 09:21:23 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:21:24 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.049491
2021-11-22 09:21:25 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.054707
2021-11-22 09:21:26 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.159092
2021-11-22 09:21:26 power_api.c:53:_get_avg_voltage: average_voltage = 21.087763
2021-11-22 09:21:26 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.09, check voltage passed.
2021-11-22 09:21:26 driver-btm-api.c:1193:check_asic_number: Chain 0 only find 0 asic, will power off hash board 0
2021-11-22 09:21:28 driver-btm-api.c:1195:check_asic_number: Chain 0 voltage: an0 = 2.809677, an2 2.816129, an6 2.538710.
2021-11-22 09:21:40 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 65 asic, times 0
2021-11-22 09:21:52 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[2]: find 65 asic, times 0
2021-11-22 09:21:57 driver-hash-chip.c:266:set_uart_relay: set uart relay to 0x330003
2021-11-22 09:21:57 driver-btm-api.c:435:set_order_clock: chain[1]: set order clock, stragegy 3
2021-11-22 09:21:57 driver-btm-api.c:435:set_order_clock: chain[2]: set order clock, stragegy 3
2021-11-22 09:21:58 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
2021-11-22 09:21:58 driver-btm-api.c:1892:check_clock_counter: freq 50 clock_counter_limit 6
2021-11-22 09:21:58 voltage[1] = 1990
2021-11-22 09:21:58 voltage[2] = 1990
2021-11-22 09:21:58 power_api.c:226:set_working_voltage_raw: working_voltage_raw = 1990
2021-11-22 09:21:59 temperature.c:340:calibrate_temp_sensor_one_chain: chain 1 temp sensor NCT218
2021-11-22 09:22:00 temperature.c:340:calibrate_temp_sensor_one_chain: chain 2 temp sensor NCT218
2021-11-22 09:22:00 uart.c:72:set_baud: set fpga_baud to 12000000
2021-11-22 09:22:01 driver-btm-api.c:293:check_bringup_temp: Bring up temperature is 25
2021-11-22 09:22:01 thread.c:1378:create_check_miner_status_thread: create thread
2021-11-22 09:22:01 thread.c:1368:create_show_miner_status_thread: create thread
2021-11-22 09:22:01 thread.c:1348:create_temperature_monitor_thread: create thread
2021-11-22 09:22:01 frequency.c:514:check_bringup_temp_dec_freq: dec freq = 0 when bringup temp = 25 dec_freq_index=0
2021-11-22 09:22:01 freq_tuning.c:183:freq_tuning_get_max_freq: Max freq of tuning is 650
2021-11-22 09:22:01 driver-btm-api.c:1765:send_null_work: [DEBUG] Send null work.
2021-11-22 09:22:01 thread.c:1338:create_asic_status_monitor_thread: create thread
2021-11-22 09:22:01 frequency.c:1110:inc_freq_with_fixed_vco: chain = 255, freq = 540, is_higher_voltage = true
2021-11-22 09:22:31 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2090, step by step.
2021-11-22 09:22:33 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:22:34 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.856598
2021-11-22 09:22:35 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.986147
2021-11-22 09:22:35 power_api.c:53:_get_avg_voltage: average_voltage = 20.921372
2021-11-22 09:22:35 power_api.c:71:check_voltage: target_vol = 20.90, actural_vol = 20.92, check voltage passed.
2021-11-22 09:27:25 frequency.c:1181:inc_asic_diff_freq_by_steps: chain = 1, start = 540, freq_step = 5
2021-11-22 09:27:26 frequency.c:1181:inc_asic_diff_freq_by_steps: chain = 2, start = 540, freq_step = 5
2021-11-22 09:27:28 driver-btm-api.c:765:set_timeout: freq = 550, percent = 90, hcn = 44236, timeout = 80
2021-11-22 09:27:28 power_api.c:310:set_to_working_voltage_by_steps: Set to voltage raw 1990, step by step.
2021-11-22 09:27:33 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:27:34 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 19.844981
2021-11-22 09:27:35 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 19.958385
2021-11-22 09:27:35 power_api.c:53:_get_avg_voltage: average_voltage = 19.901683
2021-11-22 09:27:35 power_api.c:71:check_voltage: target_vol = 19.90, actural_vol = 19.90, check voltage passed.
2021-11-22 09:27:35 thread.c:1373:create_check_system_status_thread: create thread
2021-11-22 09:27:36 driver-btm-api.c:2618:bitmain_soc_init: Init done!
2021-11-22 09:27:36 driver-btm-api.c:222:set_miner_status: STATUS_INIT
2021-11-22 09:27:40 driver-btm-api.c:222:set_miner_status: STATUS_OKAY
2021-11-22 09:27:41 frequency.c:205:get_ideal_hash_rate_GH: ideal_hash_rate = 46676
2021-11-22 09:27:41 frequency.c:223:get_sale_hash_rate_GH: sale_hash_rate = 46000
2021-11-22 09:27:44 driver-btm-api.c:1496:dhash_chip_send_job: Version num 4.
2021-11-22 09:27:44 driver-btm-api.c:1644:dhash_chip_send_job: stime.tv_sec 1637573264, block_ntime 1637573259
 

 

скрин543.jpg

Share this post


Link to post
Share on other sites
1 час назад, 425624 сказал:

Добрый день. Подскажите пожалуйста, может кто сталкивался. Купил s17+ 70th, вчера запустил, час проработал нормально, далее перестал видеть одну плату, работает только на двух, выдает 45-50th. Настройки сбрасывал.Что еще посоветуете? Логи приложил. 

  Скрыть содержимое

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203432K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25944K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12904K (cce67000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 213/154, WL threshold: 4096, image sequence number: 922123630
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 6591F6B7-A8FB-4FC6-9FAA-40343961286F, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1460/195, WL threshold: 4096, image sequence number: 3814164103
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 1C567B41-1C2F-490C-BE4A-1137496C780E, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-11-22 09:18:32 driver-btm-api.c:779:init_freq_mode: This is scan-user version
2021-11-22 09:18:32 driver-btm-api.c:2451:bitmain_soc_init: opt_multi_version     = 1
2021-11-22 09:18:32 driver-btm-api.c:2452:bitmain_soc_init: opt_bitmain_ab        = 1
2021-11-22 09:18:32 driver-btm-api.c:2453:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-11-22 09:18:32 driver-btm-api.c:2454:bitmain_soc_init: Miner compile time: Tue Jun  2 10:31:07 CST 2020 type: Antminer S17+
2021-11-22 09:18:32 driver-btm-api.c:2455:bitmain_soc_init: commit version: 1ca50a5 2020-06-01 18:51:22, build by: lol 2020-06-02 10:37:21
2021-11-22 09:18:32 driver-btm-api.c:2083:show_sn: len:16, 81540d0c69208814
2021-11-22 09:18:32 driver-btm-api.c:2461:bitmain_soc_init: show sn return 1
2021-11-22 09:18:32 driver-btm-api.c:2103:handle_sn_for_factory_mode: show sn return 1
2021-11-22 09:18:32 driver-btm-api.c:2141:handle_sn_for_factory_mode: read sn success, 81540d0c69208814
2021-11-22 09:18:32 fan.c:284:front_fan_power_on: Note: front fan is power on!
2021-11-22 09:18:32 fan.c:296:rear_fan_power_on: Note: rear fan is power on!
2021-11-22 09:18:32 driver-btm-api.c:1314:miner_device_init: Detect 256MB control board of XILINX
2021-11-22 09:18:32 driver-btm-api.c:1255:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-11-22 09:18:38 driver-btm-api.c:1239:init_miner_version: miner ID : 81540d0c69208814
2021-11-22 09:18:38 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-11-22 09:18:43 driver-btm-api.c:837:get_product_id: product_id[0] = 0
2021-11-22 09:18:43 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-11-22 09:18:43 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-11-22 09:18:43 driver-btm-api.c:2234:update_conf_by_power_feedback: Power feedback is disabled
2021-11-22 09:18:43 driver-btm-api.c:2202:get_calibration_voltage: calibration voltage flag is error data.
2021-11-22 09:18:43 driver-btm-api.c:2268:update_conf_by_power_feedback: Note: no calibration voltage, default diff = 0
2021-11-22 09:18:43 frequency.c:1457:adjust_higer_max_vol_table: adjust_higer_max_vol_table, adjust_vol = 0
2021-11-22 09:18:43 thread.c:1363:create_read_nonce_reg_thread: create thread
2021-11-22 09:18:49 driver-btm-api.c:1239:init_miner_version: miner ID : 81540d0c69208814
2021-11-22 09:18:49 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-11-22 09:18:55 driver-btm-api.c:837:get_product_id: product_id[0] = 0
2021-11-22 09:18:55 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-11-22 09:18:55 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-11-22 09:18:55 driver-btm-api.c:792:_set_project_type: project:0
2021-11-22 09:18:55 driver-btm-api.c:813:_set_project_type: Project type: Antminer S17+
2021-11-22 09:18:55 driver-btm-api.c:824:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:825:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:824:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:825:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:824:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:825:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-11-22 09:18:55 driver-btm-api.c:2372:bitmain_board_init: Fan check passed.
2021-11-22 09:18:56 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-11-22 09:18:58 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88
2021-11-22 09:18:59 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-11-22 09:19:01 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2021-11-22 09:19:02 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-11-22 09:19:04 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2021-11-22 09:19:04 thread.c:1358:create_pic_heart_beat_thread: create thread
2021-11-22 09:19:04 power_api.c:213:power_init: Power init:
2021-11-22 09:19:04 power_api.c:214:power_init: current_voltage_raw = 0
2021-11-22 09:19:04 power_api.c:215:power_init: highest_voltage_raw = 2100
2021-11-22 09:19:04 power_api.c:216:power_init: working_voltage_raw = 1950
2021-11-22 09:19:04 power_api.c:217:power_init: higher_voltage_raw  = 2040
2021-11-22 09:19:04 power_api.c:218:power_init: check_asic_voltage_raw  = 2100
2021-11-22 09:19:04 driver-btm-api.c:2382:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-11-22 09:19:36 power_api.c:324:set_to_highest_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-11-22 09:20:02 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:20:03 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.127226
2021-11-22 09:20:04 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.052097
2021-11-22 09:20:05 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.183082
2021-11-22 09:20:05 power_api.c:53:_get_avg_voltage: average_voltage = 21.120802
2021-11-22 09:20:05 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.12, check voltage passed.
2021-11-22 09:20:05 uart.c:72:set_baud: set fpga_baud to 115200
2021-11-22 09:20:16 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 0
2021-11-22 09:20:27 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 1
2021-11-22 09:20:38 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 2
2021-11-22 09:20:38 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2100
chain 0, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-11-22 09:20:46 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 3
2021-11-22 09:20:46 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2050
2021-11-22 09:20:46 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2050, step by step.
2021-11-22 09:20:50 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:20:52 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.543146
2021-11-22 09:20:53 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.520966
2021-11-22 09:20:54 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.679294
2021-11-22 09:20:54 power_api.c:53:_get_avg_voltage: average_voltage = 20.581135
2021-11-22 09:20:54 power_api.c:71:check_voltage: target_vol = 20.50, actural_vol = 20.58, check voltage passed.
chain 0, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-11-22 09:21:03 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 4
2021-11-22 09:21:03 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2000
2021-11-22 09:21:03 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2000, step by step.
2021-11-22 09:21:06 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:21:07 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.060913
2021-11-22 09:21:08 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.013978
2021-11-22 09:21:09 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.199496
2021-11-22 09:21:09 power_api.c:53:_get_avg_voltage: average_voltage = 20.091462
2021-11-22 09:21:09 power_api.c:71:check_voltage: target_vol = 20.00, actural_vol = 20.09, check voltage passed.
chain 0, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2021-11-22 09:21:18 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[0]: find 0 asic, times 5
2021-11-22 09:21:18 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw  = 2100
2021-11-22 09:21:18 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2100, step by step.
2021-11-22 09:21:23 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:21:24 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.049491
2021-11-22 09:21:25 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.054707
2021-11-22 09:21:26 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.159092
2021-11-22 09:21:26 power_api.c:53:_get_avg_voltage: average_voltage = 21.087763
2021-11-22 09:21:26 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.09, check voltage passed.
2021-11-22 09:21:26 driver-btm-api.c:1193:check_asic_number: Chain 0 only find 0 asic, will power off hash board 0
2021-11-22 09:21:28 driver-btm-api.c:1195:check_asic_number: Chain 0 voltage: an0 = 2.809677, an2 2.816129, an6 2.538710.
2021-11-22 09:21:40 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 65 asic, times 0
2021-11-22 09:21:52 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[2]: find 65 asic, times 0
2021-11-22 09:21:57 driver-hash-chip.c:266:set_uart_relay: set uart relay to 0x330003
2021-11-22 09:21:57 driver-btm-api.c:435:set_order_clock: chain[1]: set order clock, stragegy 3
2021-11-22 09:21:57 driver-btm-api.c:435:set_order_clock: chain[2]: set order clock, stragegy 3
2021-11-22 09:21:58 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
2021-11-22 09:21:58 driver-btm-api.c:1892:check_clock_counter: freq 50 clock_counter_limit 6
2021-11-22 09:21:58 voltage[1] = 1990
2021-11-22 09:21:58 voltage[2] = 1990
2021-11-22 09:21:58 power_api.c:226:set_working_voltage_raw: working_voltage_raw = 1990
2021-11-22 09:21:59 temperature.c:340:calibrate_temp_sensor_one_chain: chain 1 temp sensor NCT218
2021-11-22 09:22:00 temperature.c:340:calibrate_temp_sensor_one_chain: chain 2 temp sensor NCT218
2021-11-22 09:22:00 uart.c:72:set_baud: set fpga_baud to 12000000
2021-11-22 09:22:01 driver-btm-api.c:293:check_bringup_temp: Bring up temperature is 25
2021-11-22 09:22:01 thread.c:1378:create_check_miner_status_thread: create thread
2021-11-22 09:22:01 thread.c:1368:create_show_miner_status_thread: create thread
2021-11-22 09:22:01 thread.c:1348:create_temperature_monitor_thread: create thread
2021-11-22 09:22:01 frequency.c:514:check_bringup_temp_dec_freq: dec freq = 0 when bringup temp = 25 dec_freq_index=0
2021-11-22 09:22:01 freq_tuning.c:183:freq_tuning_get_max_freq: Max freq of tuning is 650
2021-11-22 09:22:01 driver-btm-api.c:1765:send_null_work: [DEBUG] Send null work.
2021-11-22 09:22:01 thread.c:1338:create_asic_status_monitor_thread: create thread
2021-11-22 09:22:01 frequency.c:1110:inc_freq_with_fixed_vco: chain = 255, freq = 540, is_higher_voltage = true
2021-11-22 09:22:31 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2090, step by step.
2021-11-22 09:22:33 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:22:34 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.856598
2021-11-22 09:22:35 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.986147
2021-11-22 09:22:35 power_api.c:53:_get_avg_voltage: average_voltage = 20.921372
2021-11-22 09:22:35 power_api.c:71:check_voltage: target_vol = 20.90, actural_vol = 20.92, check voltage passed.
2021-11-22 09:27:25 frequency.c:1181:inc_asic_diff_freq_by_steps: chain = 1, start = 540, freq_step = 5
2021-11-22 09:27:26 frequency.c:1181:inc_asic_diff_freq_by_steps: chain = 2, start = 540, freq_step = 5
2021-11-22 09:27:28 driver-btm-api.c:765:set_timeout: freq = 550, percent = 90, hcn = 44236, timeout = 80
2021-11-22 09:27:28 power_api.c:310:set_to_working_voltage_by_steps: Set to voltage raw 1990, step by step.
2021-11-22 09:27:33 power_api.c:85:check_voltage_multi: retry time: 0
2021-11-22 09:27:34 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 19.844981
2021-11-22 09:27:35 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 19.958385
2021-11-22 09:27:35 power_api.c:53:_get_avg_voltage: average_voltage = 19.901683
2021-11-22 09:27:35 power_api.c:71:check_voltage: target_vol = 19.90, actural_vol = 19.90, check voltage passed.
2021-11-22 09:27:35 thread.c:1373:create_check_system_status_thread: create thread
2021-11-22 09:27:36 driver-btm-api.c:2618:bitmain_soc_init: Init done!
2021-11-22 09:27:36 driver-btm-api.c:222:set_miner_status: STATUS_INIT
2021-11-22 09:27:40 driver-btm-api.c:222:set_miner_status: STATUS_OKAY
2021-11-22 09:27:41 frequency.c:205:get_ideal_hash_rate_GH: ideal_hash_rate = 46676
2021-11-22 09:27:41 frequency.c:223:get_sale_hash_rate_GH: sale_hash_rate = 46000
2021-11-22 09:27:44 driver-btm-api.c:1496:dhash_chip_send_job: Version num 4.
2021-11-22 09:27:44 driver-btm-api.c:1644:dhash_chip_send_job: stime.tv_sec 1637573264, block_ntime 1637573259
 

 

скрин543.jpg

Первая плата умерла (chain 0) в ремонт

Share this post


Link to post
Share on other sites
28.08.2020 в 13:05, scopus сказал:

правильное решение, согласен

У меня такая же проблема. С рабочей машины поставил на не рабочую такая же ошибка появилась... Потом вернул эту контрольку на свое место ошибка вентиляторов осталась. теперь у меня 2 не рабочие Т17 не знаю что и делать .

 

Share this post


Link to post
Share on other sites

Всех приветствую. S17+ Не смог найти информацию какой из 4 датчиков температуры отвечает за группу которая показывается в логе.

Ошибка sen[0] - Failed to read temp sensor type

Вопрос будет более понятен если посмотреть вложения

Скрытый текст

16277024625758558.thumb.jpg.d3aa029bfa958093f97c20c5ac0b48e3.jpg1944250218_543.jpg.5131ec2de07e16254f16c7d611cf002e.jpg.a9ed8c684a61158f93f5a49ff53226b9.jpg

 

Edited by leksey221

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Topics

    • Ремонт: Antminer s17/t17

      Кто-нибудь ремонтировал хэшплаты Antminer T17 или S17? Долго ли они работают после ремонта? У меня вот такой опыт: Antminer T17 После почти что года работы на стандартной прошивке сдохла одна хэшплата. При инициализации определялись только 24 чипа из 30. Асик стоял на балконе в шумопоглощающем ящике, что продают на Авито. От ящика до балконного окна с антикомариной сеткой были проложены 2 алюминиевые гофры чтобы горячий воздух выдувался за борт. Зимой при морозах асик тоже о

      in ASIC/FPGA майнеры

    • Antminer L3, L3+

      Доброй ночи! пожалуйста помогите кто знает с antminer l3+  работает 1.5 недели, все было хорошо.  В один момент вижу, что он выключен пришел его перезагрузил и началось   Вообщем выдает ошибку socket connect failed. connection refused то иногда включается и показывает на второй плате 21 чип место 71  много раз перезагружал, перекинул с другого асика блок питания он все равно так   не майнит уходит в ошибку   что делать подскажите пожалуйста, асику всего полторы недели скрины приложил

      in ASIC/FPGA майнеры

    • Ремонт: Bitmain Antminer s7, s9, l3+

      Официальный сайт | Antminer. Все модели. Вопросы, помощь, обсуждение.   В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы.   Статьи на bits.media:   Полезное:   (!) FAQ (часто задаваемые вопросы)   -Как найти в продаже разъемы питания, какая маркировка

      in ASIC/FPGA майнеры

    • Bitmain Antminer s9, s9k, s9j - 13,5-14,0 Th/s

      Частенько натыкаюсь на китайских поставщиков Antminer S9, предлагающих б/у машинки. Предложения самые разные, ну и размышления по этому поводу соответственно тоже. Интересно мнение форумчан - опыт таких покупок, ну и насколько это рискованно и оправдано.  

      in ASIC/FPGA майнеры

    • Antminer s19, s19pro

      BITMAIN анонсировал новый асик с улучшенными характеристиками - от 105 до 110Тх Правда инфа по железу сильно разница - то это новый чип, то они аутсорснули чипы у самсунга... Так что на самом деле? Как мне кажется, то в случае с использованием самсунга - эта контора, которая являлась много лет лидером, просто похоронит себя, т.к. самсунговские чипы уже показали, как они отлично ломаются не проработав и 5-ти наносекунд ))) Хотя те, которые переживали этот период - показывали отменные результа

      in ASIC/FPGA майнеры

×
×
  • Create New...