Перейти к содержанию

Fatal Error: Some Fan lost.Проблема с вентилятором


ASIC REPAIR

Рекомендуемые сообщения

Fatal Error: Some Fan lost or Fan speed low!

Фатальная ошибка, какой-то вентилятор потерян или скорость вентилятора слишком низкая!

tTjiDWzNpxppENhxj7d3h6s0vlhFDPpWp6BHD2uU6nSkQ02KdL-OQNWykvTIo_Cu3kqS9yA5syBu2NC-mNReNcc034PFTnrgYwvXFHK0nTQ7AAP4qSexzXeBopq-TWQ4y2zEZbhC

Нередко мы сталкиваемся с проблемой, когда у нас перестает работать Asic miner по причине выхода из строя вентилятора.

 

Разберем на примере самых популярных аппаратов и свежих* прошивок от Bitmain.

Диагностика и устранение неисправности:

Самый простой способ выявления неисправности - просмотр информации в веб интерфейсе нашего майнера, вкладка “Kernel Log”.

 

Antminer D3

Скрытый текст

Kernel Log

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 65280
[    0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 64768 pages, LIFO batch:15
[    0.000000] AM335X ES1.0 (neon )
[    0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768
[    0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
[    0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 255MB = 255MB total
[    0.000000] Memory: 238676k/238676k available, 23468k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0612cf0   (6188 kB)
[    0.000000]       .init : 0xc0613000 - 0xc06554c0   ( 266 kB)
[    0.000000]       .data : 0xc0656000 - 0xc06cc020   ( 473 kB)
[    0.000000]        .bss : 0xc06cc020 - 0xc0725e3c   ( 360 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000353] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[    0.015439] pid_max: default: 32768 minimum: 301
[    0.015670] Security Framework initialized
[    0.015764] Mount-cache hash table entries: 512
[    0.024595] Initializing cgroup subsys cpuacct
[    0.024627] Initializing cgroup subsys memory
[    0.024690] Initializing cgroup subsys blkio
[    0.024827] CPU: Testing write buffer coherency: ok
[    0.025397] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.025474] Setting up static identity map for 0x8038c820 - 0x8038c86c
[    0.026796] Brought up 1 CPUs
[    0.026821] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[    0.028111] devtmpfs: initialized
[    0.092507] pinctrl core: initialized pinctrl subsystem
[    0.092723] rstctl core: initialized rstctl subsystem
[    0.093215] regulator-dummy: no parameters
[    0.093788] NET: Registered protocol family 16
[    0.094498] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.104166] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
[    0.104349] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.105436] platform 49000000.edma: alias fck already exists
[    0.105470] platform 49000000.edma: alias fck already exists
[    0.105498] platform 49000000.edma: alias fck already exists
[    0.106647] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.106829] OMAP GPIO hardware version 0.1
[    0.108228] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.109551] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.110865] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.111499] of_get_named_gpio_flags exited with status 52
[    0.111529] gpio-rctrl rstctl.3: loaded OK
[    0.116635] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.119838] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.122026] cpsw.0: No hwaddr in dt. Using 90:70:65:3e:46:c4 from efuse
[    0.122058] cpsw.1: No hwaddr in dt. Using 90:70:65:3e:46:c6 from efuse
[    0.137596] bio: create slab <bio-0> at 0
[    0.149718] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[    0.149965] of_get_named_gpio_flags: can't parse gpios property
[    0.150251] vmmcsd_fixed: 3300 mV 
[    0.153372] SCSI subsystem initialized
[    0.153827] usbcore: registered new interface driver usbfs
[    0.153942] usbcore: registered new interface driver hub
[    0.154281] usbcore: registered new device driver usb
[    0.156404] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
[    0.156438] omap_i2c 4819c000.i2c: unable to select pin group
[    0.156631] media: Linux media interface: v0.10
[    0.156725] Linux video capture interface: v2.00
[    0.156842] pps_core: LinuxPPS API ver. 1 registered
[    0.156858] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.157577] Advanced Linux Sound Architecture Driver Initialized.
[    0.158769] Switching to clocksource gp_timer
[    0.176793] NET: Registered protocol family 2
[    0.177784] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.177874] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[    0.177965] TCP: Hash tables configured (established 2048 bind 2048)
[    0.178056] TCP: reno registered
[    0.178083] UDP hash table entries: 256 (order: 1, 12288 bytes)
[    0.178129] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[    0.178620] NET: Registered protocol family 1
[    0.179203] RPC: Registered named UNIX socket transport module.
[    0.179222] RPC: Registered udp transport module.
[    0.179236] RPC: Registered tcp transport module.
[    0.179250] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.179636] Trying to unpack rootfs image as initramfs...
[    1.941936] Freeing initrd memory: 12240K
[    1.942669] CPU PMU: probing PMU on CPU 0
[    1.942703] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[    1.943245] omap2_mbox_probe: platform not supported
[    1.947143] VFS: Disk quotas dquot_6.5.2
[    1.947379] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.948772] NFS: Registering the id_resolver key type
[    1.948865] Key type id_resolver registered
[    1.948882] Key type id_legacy registered
[    1.948949] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.949384] msgmni has been set to 490
[    1.952277] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.952303] io scheduler noop registered
[    1.952319] io scheduler deadline registered
[    1.952376] io scheduler cfq registered (default)
[    1.956448] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.958870] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[    1.959151] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[    2.619903] console [ttyO0] enabled
[    2.624484] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
[    2.633161] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
[    2.641847] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
[    2.650456] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
[    2.659474] [drm] Initialized drm 1.1.0 20060810
[    2.678137] brd: module loaded
[    2.688439] loop: module loaded
[    2.692670] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
[    2.702616] nand_get_flash_type: 2c,da against 2c,da
[    2.708142] ONFI param page 0 valid
[    2.711814] ONFI flash detected
[    2.715135] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
[    2.727045] omap2-nand: detected x8 NAND flash
[    2.731712] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    2.737294] omap2-nand: using custom ecc layout
[    2.742134] 10 ofpart partitions found on MTD device omap2-nand.0
[    2.748528] Creating 10 MTD partitions on "omap2-nand.0":
[    2.754206] 0x000000000000-0x000000020000 : "spl"
[    2.761019] 0x000000020000-0x000000040000 : "spl_backup1"
[    2.768487] 0x000000040000-0x000000060000 : "spl_backup2"
[    2.775847] 0x000000060000-0x000000080000 : "spl_backup3"
[    2.783255] 0x000000080000-0x000000240000 : "u-boot"
[    2.791464] 0x000000240000-0x000000260000 : "bootenv"
[    2.798429] 0x000000260000-0x000000280000 : "fdt"
[    2.805032] 0x000000280000-0x000000780000 : "kernel"
[    2.816065] 0x000000800000-0x000001c00000 : "root"
[    2.839560] 0x000001c00000-0x000003000000 : "config"
[    2.863340] OneNAND driver initializing
[    2.869078] usbcore: registered new interface driver asix
[    2.874894] usbcore: registered new interface driver cdc_ether
[    2.881141] usbcore: registered new interface driver smsc95xx
[    2.887259] usbcore: registered new interface driver net1080
[    2.893309] usbcore: registered new interface driver cdc_subset
[    2.899602] usbcore: registered new interface driver zaurus
[    2.905609] usbcore: registered new interface driver cdc_ncm
[    2.912355] usbcore: registered new interface driver cdc_acm
[    2.918313] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.926694] Initializing USB Mass Storage driver...
[    2.931935] usbcore: registered new interface driver usb-storage
[    2.938234] USB Mass Storage support registered.
[    2.943274] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    2.950028] musb-hdrc musb-hdrc.0.auto: pdev->id = 0
[    2.955263] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.964034] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.964055] musb-hdrc: MHDRC RTL version 2.0 
[    2.964070] musb-hdrc: setup fifo_mode 4
[    2.964098] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.964245] musb-hdrc musb-hdrc.0.auto: *** mode=3
[    2.969287] musb-hdrc musb-hdrc.0.auto: *** power=250
[    2.975338] musb-hdrc musb-hdrc.1.auto: pdev->id = 1
[    2.980577] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.989345] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.989365] musb-hdrc: MHDRC RTL version 2.0 
[    2.989379] musb-hdrc: setup fifo_mode 4
[    2.989401] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.989543] musb-hdrc musb-hdrc.1.auto: *** mode=1
[    2.994587] musb-hdrc musb-hdrc.1.auto: *** power=250
[    2.999896] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    3.006571] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
[    3.014809] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup
[    3.014913] usb usb1: default language 0x0409
[    3.014971] usb usb1: udev 1, busnum 1, minor = 0
[    3.014994] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.022146] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.029717] usb usb1: Product: MUSB HDRC host driver
[    3.034931] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd
[    3.040598] usb usb1: SerialNumber: musb-hdrc.1.auto
[    3.046569] usb usb1: usb_probe_device
[    3.046596] usb usb1: configuration #1 chosen from 1 choice
[    3.046661] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    3.046860] hub 1-0:1.0: usb_probe_interface
[    3.046882] hub 1-0:1.0: usb_probe_interface - got id
[    3.046910] hub 1-0:1.0: USB hub found
[    3.050914] hub 1-0:1.0: 1 port detected
[    3.055053] hub 1-0:1.0: standalone hub
[    3.055073] hub 1-0:1.0: individual port power switching
[    3.055092] hub 1-0:1.0: no over-current protection
[    3.055109] hub 1-0:1.0: Single TT
[    3.055130] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    3.055149] hub 1-0:1.0: power on to power good time: 10ms
[    3.055205] hub 1-0:1.0: local power source is good
[    3.055353] hub 1-0:1.0: enabling power on all ports
[    3.056412] mousedev: PS/2 mouse device common for all mice
[    3.064361] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[    3.072127] i2c /dev entries driver
[    3.077176] pps_ldisc: PPS line discipline registered
[    3.082645] Driver for 1-wire Dallas network protocol.
[    3.089920] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    3.097491] cpuidle: using governor ladder
[    3.101818] cpuidle: using governor menu
[    3.106415] of_get_named_gpio_flags exited with status 6
[    3.106435] of_get_named_gpio_flags: can't parse gpios property
[    3.106451] of_get_named_gpio_flags: can't parse gpios property
[    3.106488] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[    3.113724] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[    3.120536] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[    3.127764] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[    3.135083] mmc.4 supply vmmc_aux not found, using dummy regulator
[    3.142028] omap_hsmmc mmc.4: pins are not configured from the driver
[    3.157027] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[    3.177046] of_get_named_gpio_flags exited with status -517
[    3.177112] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.184893] ledtrig-cpu: registered to indicate activity on CPUs
[    3.191670] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[    3.198864] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[    3.206978] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[    3.213331] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[    3.220512] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[    3.232782] usbcore: registered new interface driver usbhid
[    3.238702] usbhid: USB HID core driver
[    3.245590] TCP: cubic registered
[    3.249113] Initializing XFRM netlink socket
[    3.253681] NET: Registered protocol family 17
[    3.258562] NET: Registered protocol family 15
[    3.263436] Key type dns_resolver registered
[    3.268072] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    3.276152] ThumbEE CPU extension supported.
[    3.280661] Registering SWP/SWPB emulation handler
[    3.286681] registered taskstats version 1
[    3.293293] of_get_named_gpio_flags exited with status -517
[    3.293367] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.350331] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[    3.356742] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[    3.371264] libphy: 4a101000.mdio: probed
[    3.375585] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[    3.385825] Detected MACID = 90:70:65:3e:46:c4
[    3.390504] cpsw 4a100000.ethernet: NAPI disabled
[    3.395893] of_get_named_gpio_flags exited with status -517
[    3.395958] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.404688] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    3.413966] cpu0 supply cpu0 not found, using dummy regulator
[    3.420458] cpufreq_cpu0: failed to scale voltage up: -22
[    3.426289] cpufreq_cpu0: failed to scale voltage up: -22
[    3.439061] ALSA device list:
[    3.442294]   No soundcards found.
[    3.446855] Freeing init memory: 264K
[    3.450908] Failed to execute /init
[    4.491824] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    5.922168] net eth0: initializing cpsw version 1.12 (0)
[    5.931166] net eth0: phy found : id is : 0x7c0f1
[    5.936617] libphy: PHY 4a101000.mdio:01 not found
[    5.941819] net eth0: phy 4a101000.mdio:01 not found on slave 1
[    9.009048] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
Jan  1 12:22:04 (none) local0.err cgminer: Miner compile time: Mon Nov 20 17:06:56 CST 2017 type: Antminer D3
Jan  1 12:22:04 (none) local0.warn cgminer: Started cgminer 4.9.0
Jan  1 12:22:04 (none) local0.warn cgminer[375]: bitmain_DASH_init
Jan  1 12:22:04 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:44 (none) local0.err cgminer[375]: FAN2 too slow ...
Jan 1 10:05:45 (none) local0.err cgminer[375]: FAN1 too slow ...
Jan 1 10:05:45 (none) local0.err cgminer[375]: FAN2 too slow ...
Jan 1 10:05:45 (none) local0.err cgminer[375]: FAN1 too slow ...
Jan 1 10:05:45 (none) local0.err cgminer[375]: FAN2 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

Jan 1 10:05:46 (none) local0.err cgminer[375]: FAN1 too slow ...

 

Как видим в логе Antminer D3 происходит постоянный опрос FAN1. Вентилятор не соответствует необходимым параметрам по количеству оборотов.

 

Скрытый текст

 

r_9Q1EBx-eNKr1NtxG4koa5dkyt93Jf8bdoV-UUuND_b1CbD9ac2RSUF3ftvpl70HWDiw93R_FQtb11wjNFj-fYB2nKFRa80_-vFuyZp9eL591ZGMwmeBstJj-ZrkHrei_HAa6fl

В данном случае: может быть неисправен вентилятор(не работает, не отдает информацию о своих оборотах), так же, в редких случаях, может быть виновата и контрольная плата (проверяется путем установки заведомо рабочего вентилятора).

Производим дополнительную диагностику, меняем разъемы вентилятора местами. В логе постоянная системная ошибка стала FAN2, что подтверждает неисправность вентилятора.

Устранение неисправности путем замены вентилятора, включенного в разъем FAN1.

 

Antminer L3+/L3++

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 65280
[    0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 64768 pages, LIFO batch:15
[    0.000000] AM335X ES1.0 (neon )
[    0.000000] PERCPU: Embedded 8 pages/cpu @c0933000 s9408 r8192 d15168 u32768
[    0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
[    0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 255MB = 255MB total
[    0.000000] Memory: 238896k/238896k available, 23248k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0612cf0   (6188 kB)
[    0.000000]       .init : 0xc0613000 - 0xc06554c0   ( 266 kB)
[    0.000000]       .data : 0xc0656000 - 0xc06cc020   ( 473 kB)
[    0.000000]        .bss : 0xc06cc020 - 0xc0725e3c   ( 360 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000352] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[    0.015437] pid_max: default: 32768 minimum: 301
[    0.015667] Security Framework initialized
[    0.015764] Mount-cache hash table entries: 512
[    0.024586] Initializing cgroup subsys cpuacct
[    0.024617] Initializing cgroup subsys memory
[    0.024680] Initializing cgroup subsys blkio
[    0.024817] CPU: Testing write buffer coherency: ok
[    0.025385] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.025462] Setting up static identity map for 0x8038c820 - 0x8038c86c
[    0.026789] Brought up 1 CPUs
[    0.026812] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[    0.028121] devtmpfs: initialized
[    0.092533] pinctrl core: initialized pinctrl subsystem
[    0.092750] rstctl core: initialized rstctl subsystem
[    0.093243] regulator-dummy: no parameters
[    0.093811] NET: Registered protocol family 16
[    0.094515] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.104176] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
[    0.104361] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.105447] platform 49000000.edma: alias fck already exists
[    0.105482] platform 49000000.edma: alias fck already exists
[    0.105510] platform 49000000.edma: alias fck already exists
[    0.106663] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.106844] OMAP GPIO hardware version 0.1
[    0.108252] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.109575] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.110893] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.111525] of_get_named_gpio_flags exited with status 52
[    0.111556] gpio-rctrl rstctl.3: loaded OK
[    0.116660] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.119863] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.122044] cpsw.0: No hwaddr in dt. Using 18:93:d7:f4:e3:50 from efuse
[    0.122077] cpsw.1: No hwaddr in dt. Using 18:93:d7:f4:e3:52 from efuse
[    0.137621] bio: create slab <bio-0> at 0
[    0.149766] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[    0.150009] of_get_named_gpio_flags: can't parse gpios property
[    0.150301] vmmcsd_fixed: 3300 mV 
[    0.153408] SCSI subsystem initialized
[    0.153863] usbcore: registered new interface driver usbfs
[    0.153977] usbcore: registered new interface driver hub
[    0.154306] usbcore: registered new device driver usb
[    0.156408] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
[    0.156441] omap_i2c 4819c000.i2c: unable to select pin group
[    0.156634] media: Linux media interface: v0.10
[    0.156728] Linux video capture interface: v2.00
[    0.156846] pps_core: LinuxPPS API ver. 1 registered
[    0.156861] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.157581] Advanced Linux Sound Architecture Driver Initialized.
[    0.158778] Switching to clocksource gp_timer
[    0.176783] NET: Registered protocol family 2
[    0.177779] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.177868] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[    0.177958] TCP: Hash tables configured (established 2048 bind 2048)
[    0.178050] TCP: reno registered
[    0.178077] UDP hash table entries: 256 (order: 1, 12288 bytes)
[    0.178124] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[    0.178617] NET: Registered protocol family 1
[    0.179206] RPC: Registered named UNIX socket transport module.
[    0.179227] RPC: Registered udp transport module.
[    0.179241] RPC: Registered tcp transport module.
[    0.179254] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.179641] Trying to unpack rootfs image as initramfs...
[    1.916979] Freeing initrd memory: 12020K
[    1.917630] CPU PMU: probing PMU on CPU 0
[    1.917662] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[    1.918210] omap2_mbox_probe: platform not supported
[    1.922092] VFS: Disk quotas dquot_6.5.2
[    1.922329] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.923769] NFS: Registering the id_resolver key type
[    1.923861] Key type id_resolver registered
[    1.923880] Key type id_legacy registered
[    1.923945] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.924388] msgmni has been set to 490
[    1.927264] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.927291] io scheduler noop registered
[    1.927307] io scheduler deadline registered
[    1.927356] io scheduler cfq registered (default)
[    1.931390] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.933836] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[    1.934121] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[    2.594958] console [ttyO0] enabled
[    2.599501] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
[    2.608213] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
[    2.616847] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
[    2.625464] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
[    2.634488] [drm] Initialized drm 1.1.0 20060810
[    2.653184] brd: module loaded
[    2.663454] loop: module loaded
[    2.667636] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
[    2.677615] nand_get_flash_type: 2c,da against 2c,da
[    2.683142] ONFI param page 0 valid
[    2.686816] ONFI flash detected
[    2.690136] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
[    2.702049] omap2-nand: detected x8 NAND flash
[    2.706713] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    2.712296] omap2-nand: using custom ecc layout
[    2.717139] 10 ofpart partitions found on MTD device omap2-nand.0
[    2.723533] Creating 10 MTD partitions on "omap2-nand.0":
[    2.729212] 0x000000000000-0x000000020000 : "spl"
[    2.736018] 0x000000020000-0x000000040000 : "spl_backup1"
[    2.743465] 0x000000040000-0x000000060000 : "spl_backup2"
[    2.750899] 0x000000060000-0x000000080000 : "spl_backup3"
[    2.758255] 0x000000080000-0x000000240000 : "u-boot"
[    2.766528] 0x000000240000-0x000000260000 : "bootenv"
[    2.773459] 0x000000260000-0x000000280000 : "fdt"
[    2.780111] 0x000000280000-0x000000780000 : "kernel"
[    2.791113] 0x000000800000-0x000001c00000 : "root"
[    2.814597] 0x000001c00000-0x000003000000 : "config"
[    2.838372] OneNAND driver initializing
[    2.844099] usbcore: registered new interface driver asix
[    2.849921] usbcore: registered new interface driver cdc_ether
[    2.856201] usbcore: registered new interface driver smsc95xx
[    2.862319] usbcore: registered new interface driver net1080
[    2.868344] usbcore: registered new interface driver cdc_subset
[    2.874639] usbcore: registered new interface driver zaurus
[    2.880645] usbcore: registered new interface driver cdc_ncm
[    2.887447] usbcore: registered new interface driver cdc_acm
[    2.893391] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.901770] Initializing USB Mass Storage driver...
[    2.907030] usbcore: registered new interface driver usb-storage
[    2.913330] USB Mass Storage support registered.
[    2.918372] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    2.925084] musb-hdrc musb-hdrc.0.auto: pdev->id = 0
[    2.930330] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.939102] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.939123] musb-hdrc: MHDRC RTL version 2.0 
[    2.939139] musb-hdrc: setup fifo_mode 4
[    2.939167] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.939311] musb-hdrc musb-hdrc.0.auto: *** mode=3
[    2.944356] musb-hdrc musb-hdrc.0.auto: *** power=250
[    2.950392] musb-hdrc musb-hdrc.1.auto: pdev->id = 1
[    2.955639] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[    2.964411] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    2.964431] musb-hdrc: MHDRC RTL version 2.0 
[    2.964445] musb-hdrc: setup fifo_mode 4
[    2.964468] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    2.964616] musb-hdrc musb-hdrc.1.auto: *** mode=1
[    2.969661] musb-hdrc musb-hdrc.1.auto: *** power=250
[    2.974969] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    2.981379] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
[    2.989620] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup
[    2.989722] usb usb1: default language 0x0409
[    2.989779] usb usb1: udev 1, busnum 1, minor = 0
[    2.989804] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.996932] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.004529] usb usb1: Product: MUSB HDRC host driver
[    3.009746] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd
[    3.015412] usb usb1: SerialNumber: musb-hdrc.1.auto
[    3.021621] usb usb1: usb_probe_device
[    3.021651] usb usb1: configuration #1 chosen from 1 choice
[    3.021720] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    3.021924] hub 1-0:1.0: usb_probe_interface
[    3.021946] hub 1-0:1.0: usb_probe_interface - got id
[    3.021974] hub 1-0:1.0: USB hub found
[    3.025992] hub 1-0:1.0: 1 port detected
[    3.030134] hub 1-0:1.0: standalone hub
[    3.030153] hub 1-0:1.0: individual port power switching
[    3.030171] hub 1-0:1.0: no over-current protection
[    3.030189] hub 1-0:1.0: Single TT
[    3.030211] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    3.030231] hub 1-0:1.0: power on to power good time: 10ms
[    3.030288] hub 1-0:1.0: local power source is good
[    3.030401] hub 1-0:1.0: enabling power on all ports
[    3.031464] mousedev: PS/2 mouse device common for all mice
[    3.039392] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[    3.046897] 44e3e000.rtc: already running
[    3.051391] i2c /dev entries driver
[    3.056422] pps_ldisc: PPS line discipline registered
[    3.061901] Driver for 1-wire Dallas network protocol.
[    3.069177] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    3.076735] cpuidle: using governor ladder
[    3.081062] cpuidle: using governor menu
[    3.085642] of_get_named_gpio_flags exited with status 6
[    3.085662] of_get_named_gpio_flags: can't parse gpios property
[    3.085677] of_get_named_gpio_flags: can't parse gpios property
[    3.085714] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[    3.092939] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[    3.099755] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[    3.106979] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[    3.114303] mmc.4 supply vmmc_aux not found, using dummy regulator
[    3.121259] omap_hsmmc mmc.4: pins are not configured from the driver
[    3.131656] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[    3.155571] of_get_named_gpio_flags exited with status -517
[    3.155637] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.163414] ledtrig-cpu: registered to indicate activity on CPUs
[    3.170198] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[    3.177394] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[    3.185559] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[    3.191849] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[    3.199026] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[    3.211279] usbcore: registered new interface driver usbhid
[    3.217195] usbhid: USB HID core driver
[    3.224104] TCP: cubic registered
[    3.227626] Initializing XFRM netlink socket
[    3.232198] NET: Registered protocol family 17
[    3.237092] NET: Registered protocol family 15
[    3.241948] Key type dns_resolver registered
[    3.246582] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    3.254665] ThumbEE CPU extension supported.
[    3.259175] Registering SWP/SWPB emulation handler
[    3.265183] registered taskstats version 1
[    3.271822] of_get_named_gpio_flags exited with status -517
[    3.271892] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.328855] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[    3.335266] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[    3.349806] libphy: 4a101000.mdio: probed
[    3.354124] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[    3.364359] Detected MACID = 18:93:d7:f4:e3:50
[    3.369044] cpsw 4a100000.ethernet: NAPI disabled
[    3.374436] of_get_named_gpio_flags exited with status -517
[    3.374502] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    3.383215] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    3.392494] cpu0 supply cpu0 not found, using dummy regulator
[    3.398988] cpufreq_cpu0: failed to scale voltage up: -22
[    3.404820] cpufreq_cpu0: failed to scale voltage up: -22
[    3.417610] ALSA device list:
[    3.420840]   No soundcards found.
[    3.425393] Freeing init memory: 264K
[    3.429440] Failed to execute /init
[    4.432381] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    5.723452] net eth0: initializing cpsw version 1.12 (0)
[    5.732337] net eth0: phy found : id is : 0x7c0f1
[    5.737776] libphy: PHY 4a101000.mdio:01 not found
[    5.742971] net eth0: phy 4a101000.mdio:01 not found on slave 1
[    8.809828] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
Jan  7 09:23:03 (none) local0.err cgminer: Miner compile time: Fri May 11 11:00:44 CST 2018 type: Antminer L3++
Jan  7 09:23:03 (none) local0.warn cgminer: Started cgminer 4.9.0
Jan  7 09:23:03 (none) local0.notice cgminer[375]:  detected at /sys/class/gpio/gpio51/value  chain 0
Jan  7 09:23:03 (none) local0.notice cgminer[375]:  detected at /sys/class/gpio/gpio48/value  chain 1
Jan  7 09:23:03 (none) local0.notice cgminer[375]:  detected at /sys/class/gpio/gpio47/value  chain 2
Jan  7 09:23:03 (none) local0.notice cgminer[375]:  detected at /sys/class/gpio/gpio44/value  chain 3
Jan  7 09:23:03 (none) local0.notice cgminer[375]: detect total chain num 4
Jan  7 09:23:03 (none) local0.notice cgminer[375]: i2c init ok
Jan  7 09:23:13 (none) local0.notice cgminer[375]: in tty_init
Jan  7 09:23:13 (none) local0.notice cgminer[375]: tty_init 0
Jan  7 09:23:13 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[0]
Jan  7 09:23:13 (none) local0.notice cgminer[375]: tty_init 1
Jan  7 09:23:13 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[1]
Jan  7 09:23:13 (none) local0.notice cgminer[375]: tty_init 2
Jan  7 09:23:13 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[2]
Jan  7 09:23:13 (none) local0.notice cgminer[375]: tty_init 3
Jan  7 09:23:13 (none) local0.notice cgminer[375]: Start A New Asic Response.Chain Id:[3]
Jan  7 09:23:13 (none) local0.notice cgminer[375]: open device over
Jan  7 09:23:14 (none) local0.notice cgminer[375]: send cmd to get chip address
Jan  7 09:23:14 (none) local0.err cgminer[375]: bitmain_scanreg,crc5 error,should be 00,but check as 13 201 244
Jan  7 09:23:14 (none) local0.err cgminer[375]: bitmain_scanreg: reg_value = 0x14859c00
Jan  7 09:23:14 (none) local0.err cgminer[375]: bitmain_scanreg,crc5 error,should be 00,but check as 13 202 244
Jan  7 09:23:14 (none) local0.err cgminer[375]: bitmain_scanreg: reg_value = 0x1814859c
Jan  7 09:23:16 (none) local0.notice cgminer[375]: Chain 0 ASIC 71 !!!
Jan  7 09:23:16 (none) local0.notice cgminer[375]: Chain 1 ASIC 72 !!!
Jan  7 09:23:16 (none) local0.notice cgminer[375]: Chain 2 ASIC 72 !!!
Jan  7 09:23:16 (none) local0.notice cgminer[375]: Chain 3 ASIC 29 !!!
Jan  7 09:23:16 (none) local0.notice cgminer[375]: Need to recheck asic num !!!
Jan  7 09:23:24 (none) local0.err cgminer: Miner compile time: Fri May 11 11:00:44 CST 2018 type: Antminer L3++
Jan  7 09:23:24 (none) local0.warn cgminer: Started cgminer 4.9.0
Jan  7 09:23:24 (none) local0.notice cgminer[449]:  detected at /sys/class/gpio/gpio51/value  chain 0
Jan  7 09:23:24 (none) local0.notice cgminer[449]:  detected at /sys/class/gpio/gpio48/value  chain 1
Jan  7 09:23:24 (none) local0.notice cgminer[449]:  detected at /sys/class/gpio/gpio47/value  chain 2
Jan  7 09:23:24 (none) local0.notice cgminer[449]:  detected at /sys/class/gpio/gpio44/value  chain 3
Jan  7 09:23:24 (none) local0.notice cgminer[449]: detect total chain num 4
Jan  7 09:23:24 (none) local0.notice cgminer[449]: i2c init ok
Jan  7 09:23:33 (none) local0.notice cgminer[449]: in tty_init
Jan  7 09:23:33 (none) local0.notice cgminer[449]: tty_init 0
Jan  7 09:23:33 (none) local0.notice cgminer[449]: Start A New Asic Response.Chain Id:[0]
Jan  7 09:23:33 (none) local0.notice cgminer[449]: tty_init 1
Jan  7 09:23:33 (none) local0.notice cgminer[449]: Start A New Asic Response.Chain Id:[1]
Jan  7 09:23:33 (none) local0.notice cgminer[449]: tty_init 2
Jan  7 09:23:33 (none) local0.notice cgminer[449]: Start A New Asic Response.Chain Id:[2]
Jan  7 09:23:34 (none) local0.notice cgminer[449]: tty_init 3
Jan  7 09:23:34 (none) local0.notice cgminer[449]: Start A New Asic Response.Chain Id:[3]
Jan  7 09:23:34 (none) local0.notice cgminer[449]: open device over
Jan  7 09:23:34 (none) local0.notice cgminer[449]: send cmd to get chip address
Jan  7 09:23:34 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 18,but check as 13 92 287
Jan  7 09:23:34 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x14859c00
Jan  7 09:23:36 (none) local0.notice cgminer[449]: Chain 0 ASIC 72 !!!
Jan  7 09:23:36 (none) local0.notice cgminer[449]: Chain 1 ASIC 72 !!!
Jan  7 09:23:36 (none) local0.notice cgminer[449]: Chain 2 ASIC 72 !!!
Jan  7 09:23:36 (none) local0.notice cgminer[449]: Chain 3 ASIC 71 !!!
Jan  7 09:23:36 (none) local0.notice cgminer[449]: Need to recheck asic num !!!
Jan  7 09:23:36 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 18,but check as 13 89 228
Jan  7 09:23:36 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x14859c00
Jan  7 09:23:38 (none) local0.notice cgminer[449]: Chain 0 ASIC 72 !!!
Jan  7 09:23:38 (none) local0.notice cgminer[449]: Chain 1 ASIC 72 !!!
Jan  7 09:23:38 (none) local0.notice cgminer[449]: Chain 2 ASIC 72 !!!
Jan  7 09:23:38 (none) local0.notice cgminer[449]: Chain 3 ASIC 12 !!!
Jan  7 09:23:38 (none) local0.notice cgminer[449]: Need to recheck asic num !!!
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 18,but check as 13 96 119
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x14859c00
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 1e 1 4
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x14859c00
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 18 2 4
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x14859c14
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 14 3 4
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x00001e14
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 14 0 3
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x00001814
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 14 1 3
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x00001814
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 14 2 3
Jan  7 09:23:38 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x00001814
Jan  7 09:23:40 (none) local0.notice cgminer[449]: Chain 0 ASIC 72 !!!
Jan  7 09:23:40 (none) local0.notice cgminer[449]: Chain 1 ASIC 72 !!!
Jan  7 09:23:40 (none) local0.notice cgminer[449]: Chain 2 ASIC 72 !!!
Jan  7 09:23:40 (none) local0.notice cgminer[449]: Chain 3 ASIC 56 !!!
Jan  7 09:23:40 (none) local0.notice cgminer[449]: Need to recheck asic num !!!
Jan  7 09:23:44 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x1e14859c
Jan  7 09:23:44 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 13 26 29
Jan  7 09:23:44 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x1814859c
Jan  7 09:23:44 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 13 27 29
Jan  7 09:23:44 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x1814859c
Jan  7 09:23:44 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 00,but check as 13 28 29
Jan  7 09:23:44 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x1814859c
Jan  7 09:23:46 (none) local0.notice cgminer[449]: Chain 0 ASIC 72 !!!
Jan  7 09:23:46 (none) local0.notice cgminer[449]: Chain 1 ASIC 72 !!!
Jan  7 09:23:46 (none) local0.notice cgminer[449]: Chain 2 ASIC 72 !!!
Jan  7 09:23:46 (none) local0.notice cgminer[449]: Chain 3 ASIC 71 !!!
Jan  7 09:23:46 (none) local0.notice cgminer[449]: addrInterval = '3'
Jan  7 09:23:46 (none) local0.notice cgminer[449]: software_set_address: chain 0 has 72 ASIC, and addrInterval is 3
Jan  7 09:23:46 (none) local0.notice cgminer[449]: Now Set [0] Chain Address
Jan  7 09:23:47 (none) local0.notice cgminer[449]: software_set_address: chain 1 has 72 ASIC, and addrInterval is 3
Jan  7 09:23:47 (none) local0.notice cgminer[449]: Now Set [1] Chain Address
Jan  7 09:23:48 (none) local0.notice cgminer[449]: software_set_address: chain 2 has 72 ASIC, and addrInterval is 3
Jan  7 09:23:48 (none) local0.notice cgminer[449]: Now Set [2] Chain Address
Jan  7 09:23:49 (none) local0.notice cgminer[449]: software_set_address: chain 3 has 71 ASIC, and addrInterval is 3
Jan  7 09:23:49 (none) local0.notice cgminer[449]: Now Set [3] Chain Address
Jan  7 09:23:50 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 17,but check as 10 7 14
Jan  7 09:23:50 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x14859457
Jan  7 09:23:50 (none) local0.notice cgminer[449]: frequency = '450'
Jan  7 09:23:50 (none) local0.notice cgminer[449]: dev.timeout = 16
Jan  7 09:23:50 (none) local0.notice cgminer[449]: opt_bitmain_L3_core_temp : 2
Jan  7 09:23:51 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 01,but check as 0c 96 285
Jan  7 09:23:51 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x41403a10
Jan  7 09:23:51 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 01,but check as 0c 97 285
Jan  7 09:23:51 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x403a1006
Jan  7 09:23:51 (none) local0.err cgminer[449]: bitmain_scanreg,crc5 error,should be 01,but check as 0c 284 285
Jan  7 09:23:51 (none) local0.err cgminer[449]: bitmain_scanreg: reg_value = 0x403a104b
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][0][1E]@ChainID:[0], Chip[C]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][0][1E]@ChainID:[1], Chip[C]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][0][1E]@ChainID:[2], Chip[C]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][0][1E]@ChainID:[0], Chip[C]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][0][1E]@ChainID:[1], Chip[C]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][0][1E]@ChainID:[2], Chip[C]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][0][0]@ChainID:[2], Chip[C9]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][0][0]@ChainID:[0], Chip[C9]
Jan  7 09:23:51 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][0][0]@ChainID:[1], Chip[C9]
Jan  7 09:24:16 (none) local0.err cgminer[449]: Get [1]Temp Data Failed!
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][1][20]@ChainID:[0], Chip[C]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][1][1F]@ChainID:[1], Chip[C]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][1][1F]@ChainID:[2], Chip[C]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Chain 0 chip 0 RemoteTemp 0x20
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Chain 1 chip 0 RemoteTemp 0x1f
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Chain 2 chip 0 RemoteTemp 0x1f
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[0], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[1], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Dump IIC Data:[41][98][1][0]@ChainID:[2], Chip[C9]
Jan  7 09:24:17 (none) local0.notice cgminer[449]: OK Chain 0 chip 0 local 0x1e remote 0x20 offset 0xfffffffa 
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Remote = 0 Chain 0 chip 1 local 0x0 remote 0x0 offset 0x4 
Jan  7 09:24:17 (none) local0.notice cgminer[449]: OK Chain 1 chip 0 local 0x1f remote 0x1f offset 0xfffffff9 
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0x4 
Jan  7 09:24:17 (none) local0.notice cgminer[449]: OK Chain 2 chip 0 local 0x20 remote 0x1f offset 0xfffffff9 
Jan  7 09:24:17 (none) local0.notice cgminer[449]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0x4 
Jan  7 09:24:18 (none) local0.notice cgminer[449]: send cmd to open block
Jan  7 09:24:18 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][11][FA]@ChainID:[0], Chip[C]
Jan  7 09:24:18 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][11][F9]@ChainID:[1], Chip[C]
Jan  7 09:24:18 (none) local0.notice cgminer[449]: Dump IIC Data:[1][98][11][F9]@ChainID:[2], Chip[C]
Jan  7 09:24:20 (none) local0.err cgminer[449]: cgminer time error total_secs = 1546853060.845796 last_total_secs = 1.000000
Jan  7 09:24:22 (none) local0.warn cgminer[449]: Pool 0 stratum+tcp://stratum-ltc.antpool.com:8888 alive, testing stability
Jan  7 09:24:22 (none) local0.warn cgminer[449]: Switching to pool 0 stratum+tcp://stratum-ltc.antpool.com:8888
Jan  7 09:24:27 (none) local0.warn cgminer[449]: API running in IP access mode on port 4028 (15)
Jan  7 09:24:42 (none) local0.err cgminer[449]: Fan Err! Disable PIC! Fan2 speed is too low 0 pwm 36 
Jan  7 09:24:43 (none) local0.err cgminer[449]: Net Err! lastest job more than 2 mins! waiting ...

В данном логе опрос вентилятора происходит в самом конце, неисправен Fan2.

Устранение неисправности точно такое же как и с Antminer D3 - производим замену неисправного вентилятора, в данном случае Fan2.

Скрытый текст

xALqjvhDGAcy16dts24laj-b1l43JBlRq_1-asKzn4ygENEKIAe14WtG-7nd6t2Rn4l7szbQvqGsi6mx3np3EhOIHUwoOdm1cZddglUVdZ1e8kNCTR2IWrcQkaUo-r5VlbdOFO2r

 

Редкая неисправность:

Fan Err! Disable PIC! Fan num is 0 - система не увидела ни один из вентиляторов, требуется замена двух вентиляторов.

 

Antminer S9/S9i/S9j

 

Обозначение вентиляторов в логе и веб интерфейсе отличается, в логе - Fan[2]/Fan[5], в веб интерфейсе Fan 3/Fan 6.

Скрытый текст

qkIt3GvmOPSoO81XLOr7JDsbCks8GVVvKeRnp6Y_KH23fi91tsX01mpcjLfYs2xfSjy1pPvWlo9KY18n6SIMgxbKmjfPFAeASa3BBlfgKalr6UBl5eBP2hVOSgeHS4MsQzL0wgCN

Скрытый текст

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]     Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000308] ps7-ttc #0 at f0006000, irq=43
[    0.000616] Console: colour dummy device 80x30
[    0.000653] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040211] pid_max: default: 32768 minimum: 301
[    0.040431] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040453] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042570] CPU: Testing write buffer coherency: ok
[    0.042917] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042977] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043200] L310 cache controller enabled
[    0.043220] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121038] CPU1: Booted secondary processor
[    0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210360] Brought up 2 CPUs
[    0.210380] SMP: Total of 2 processors activated.
[    0.210388] CPU: All CPU(s) started in SVC mode.
[    0.211055] devtmpfs: initialized
[    0.213464] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214675] regulator-dummy: no parameters
[    0.222350] NET: Registered protocol family 16
[    0.224477] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226759] cpuidle: using governor ladder
[    0.226773] cpuidle: using governor menu
[    0.234222] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235740] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235753] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235868] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.257513] bio: create slab <bio-0> at 0
[    0.258934] vgaarb: loaded
[    0.259647] SCSI subsystem initialized
[    0.260678] usbcore: registered new interface driver usbfs
[    0.260849] usbcore: registered new interface driver hub
[    0.261113] usbcore: registered new device driver usb
[    0.261697] media: Linux media interface: v0.10
[    0.261854] Linux video capture interface: v2.00
[    0.262090] pps_core: LinuxPPS API ver. 1 registered
[    0.262102] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.262224] PTP clock support registered
[    0.262583] EDAC MC: Ver: 3.0.0
[    0.263624] Advanced Linux Sound Architecture Driver Initialized.
[    0.266464] DMA-API: preallocated 4096 debug entries
[    0.266476] DMA-API: debugging enabled by kernel config
[    0.266550] Switched to clocksource arm_global_timer
[    0.287285] NET: Registered protocol family 2
[    0.287939] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.288034] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.288193] TCP: Hash tables configured (established 8192 bind 8192)
[    0.288251] TCP: reno registered
[    0.288271] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.288320] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.288592] NET: Registered protocol family 1
[    0.288907] RPC: Registered named UNIX socket transport module.
[    0.288919] RPC: Registered udp transport module.
[    0.288927] RPC: Registered tcp transport module.
[    0.288936] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288950] PCI: CLS 0 bytes, default 64
[    0.289386] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291405] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292794] bounce pool size: 64 pages
[    0.293704] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293904] msgmni has been set to 1486
[    0.294667] io scheduler noop registered
[    0.294680] io scheduler deadline registered
[    0.294722] io scheduler cfq registered (default)
[    0.308276] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.308297] dma-pl330 f8003000.ps7-dma:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.430120] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.002194] console [ttyPS0] enabled
[    1.006445] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.014081] [drm] Initialized drm 1.1.0 20060810
[    1.031275] brd: module loaded
[    1.040680] loop: module loaded
[    1.050170] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.055924] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.063871] libphy: XEMACPS mii bus: probed
[    1.068347] ------------- phy_id = 0x3625e62
[    1.073078] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.081943] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.088775] ehci-pci: EHCI PCI platform driver
[    1.095991] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.102819] usbcore: registered new interface driver usb-storage
[    1.109705] mousedev: PS/2 mouse device common for all mice
[    1.115788] i2c /dev entries driver
[    1.122714] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.128234] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.134117] Xilinx Zynq CpuIdle Driver started
[    1.139005] sdhci: Secure Digital Host Controller Interface driver
[    1.145101] sdhci: Copyright(c) Pierre Ossman
[    1.149468] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.156243] mmc0: no vqmmc regulator found
[    1.160358] mmc0: no vmmc regulator found
[    1.196576] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.205260] usbcore: registered new interface driver usbhid
[    1.210777] usbhid: USB HID core driver
[    1.215479] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.221777] nand: Micron MT29F2G08ABAEAWP
[    1.225742] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.231699] Bad block table found at page 131008, version 0x01
[    1.237936] Bad block table found at page 130944, version 0x01
[    1.243989] 3 ofpart partitions found on MTD device pl353-nand
[    1.249768] Creating 3 MTD partitions on "pl353-nand":
[    1.254864] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.262909] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.270223] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.279155] TCP: cubic registered
[    1.282389] NET: Registered protocol family 17
[    1.287100] Registering SWP/SWPB emulation handler
[    1.293048] regulator-dummy: disabling
[    1.297402] UBI: attaching mtd1 to ubi0
[    1.831338] UBI: scanning is finished
[    1.843084] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.850166] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.856926] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.863591] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.870468] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.876437] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.883569] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1105122292
[    1.892599] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.901816] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.901822] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.905714] ALSA device list:
[    1.905718]   No soundcards found.
[    1.922169] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.951529] UBIFS: recovery needed
[    2.055988] UBIFS: recovery completed
[    2.059682] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.065603] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.074736] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.084621] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.089661] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 3B7239D8-21A7-4628-8BEE-5D1CF3D22D35, small LPT model
[    2.100956] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.108157] devtmpfs: mounted
[    2.111263] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.961216] random: dd urandom read with 0 bits of entropy available
[    3.356581] 
[    3.356581] bcm54xx_config_init
[    3.966585] 
[    3.966585] bcm54xx_config_init
[    7.967437] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.973529] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   24.439689] In axi fpga driver!
[   24.442759] request_mem_region OK!
[   24.446151] AXI fpga dev virtual address is 0xf01fe000
[   24.451287] *base_vir_addr = 0x8c510
[   24.466380] In fpga mem driver!
[   24.469734] request_mem_region OK!
[   24.473245] fpga mem virtual address is 0xf3000000
[   25.276592] 
[   25.276592] bcm54xx_config_init
[   25.906607] 
[   25.906607] bcm54xx_config_init
[   29.907445] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   29.913464] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  107.523114] random: nonblocking pool is initialized
main.c:13927: log_level = 4
main.c:13954: This is XILINX board. Totalram:       1039794176
main.c:13960: Detect 1GB control board of XILINX
driver-bitmain.c:1003: forceFreq=-1 forceFlag=0
main.c:8434: DETECT HW version=0008c510
main.c:13999: miner ID : 802815487600881c
main.c:14024: Miner Type = S9
main.c:14036: AsicType = 1387
main.c:14039: real AsicNum = 63
main.c:14132: use critical mode to search freq...
driver-bitmain.c:2401: get PLUG ON=0x000000e0
driver-bitmain.c:2471: Find hashboard on Chain[5]
driver-bitmain.c:2471: Find hashboard on Chain[6]
driver-bitmain.c:2471: Find hashboard on Chain[7]
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
main.c:2164: Check chain[5] PIC fw version=0x03
main.c:2164: Check chain[6] PIC fw version=0x03
main.c:2164: Check chain[7] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[5] has freq in PIC and will jump over...
main.c:8965: Chain[5] has core num in PIC
main.c:2164: Check chain[5] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[6] has freq in PIC and will jump over...
main.c:8965: Chain[6] has core num in PIC
main.c:2164: Check chain[6] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[7] has freq in PIC and will jump over...
main.c:8965: Chain[7] has core num in PIC
main.c:2164: Check chain[7] PIC fw version=0x03
main.c:9039: get PIC voltage=91 on chain[5], value=890
main.c:9039: get PIC voltage=91 on chain[6], value=890
main.c:9039: get PIC voltage=91 on chain[7], value=890
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:9205: chain[5] temp offset record: 62,0,0,0,0,0,35,28
main.c:9222: chain[5] temp chip I2C addr=0x98
main.c:9228: chain[5] has no middle temp, use special fix mode.
main.c:9205: chain[6] temp offset record: 62,0,0,0,0,0,35,28
main.c:9222: chain[6] temp chip I2C addr=0x98
main.c:9228: chain[6] has no middle temp, use special fix mode.
main.c:9205: chain[7] temp offset record: 62,0,0,0,0,0,35,28
main.c:9222: chain[7] temp chip I2C addr=0x98
main.c:9228: chain[7] has no middle temp, use special fix mode.
main.c:13838: total_exist_chain_num = 3
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:9456: CRC error counter=0
main.c:9471: set command mode to VIL
main.c:9543: 
--- check asic number
main.c:9640: After Get ASIC NUM CRC error counter=0
main.c:9663: set_baud=0
main.c:10588: The min freq=700
main.c:10590: set real timeout 52, need sleep=379392
main.c:12720: After TEST CRC error counter=0
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:14167: search freq for 1 times, completed chain = 3, total chain num = 3 
board_frq_tuning.c:549: single_board_frq_tuning enter
board_frq_tuning.c:550: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:132: force_freq not set, don't need tuning
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:14559: restart Miner chance num=2
main.c:14599: waiting for receive_func to exit!
main.c:14613: waiting for pic heart to exit!
main.c:13809: bmminer not found= 1765 root       0:00 grep bmminer

main.c:14657: bmminer not found, restart bmminer ...
This is the first time running after searching freq!
Detect 1GB control board of XILINX
Miner Type = S9
Miner compile time: Fri Jul 13 10:46:43 CST 2018 type: Antminer S9j
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 802815487600881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=2400
get fan[2] speed=2400
get fan[2] speed=2400
get fan[5] speed=5880
get fan[2] speed=2400
get fan[5] speed=5880
get fan[2] speed=2400
get fan[5] speed=5880
get fan[2] speed=2400
get fan[5] speed=5880
get fan[2] speed=2400
get fan[5] speed=5880
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
get fan[2] speed=2400
get fan[5] speed=5880
get fan[2] speed=2400
get fan[5] speed=5880
get fan[2] speed=2280
get fan[5] speed=5880
get fan[2] speed=2280
get fan[5] speed=5880
get fan[2] speed=2400
get fan[5] speed=5880
get fan[2] speed=2400
get fan[5] speed=5880
get fan[2] speed=2280
get fan[5] speed=5880
get fan[2] speed=2280
get fan[5] speed=5880
get fan[2] speed=2280
get fan[5] speed=5880
get fan[2] speed=2400
get fan[5] speed=5880
Fatal Error: some Fan lost or Fan speed low!

Один из вентиляторов, Fan[2], в логе показывает слишком низкие обороты, данный тест не пройден, необходима замена.

 

Скрытый текст

Miner Type = S9
Miner compile time: Fri Jul 13 10:46:43 CST 2018 type: Antminer S9j
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 802815487600881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[5] speed=5880
get fan[5] speed=5880

get fan[5] speed=5880

get fan[5] speed=5880

driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:4965:check_fan_beforeInit: waiting fans become stable...
get fan[5] speed=5880

get fan[5] speed=5880

get fan[5] speed=5880

get fan[5] speed=5880

get fan[5] speed=5880

get fan[5] speed=5880
Fatal Error: some Fan lost or Fan speed low!

Постоянно опрашивает Fan[5], но обороты соответствуют рабочему режиму, а Fan[2] из лога пропал. Fan[2] не подключен или же не крутится, необходима замена вентилятора.

 

Следует помнить что вентиляторы устанавливаются на аппарат в определенном порядке, с одной стороны вентилятор должен всасывать холодный воздух, а с другой - вытягивать горячий.

Скрытый текст

photo_2019-01-10_13-08-39.thumb.jpg.f6602c3ec1ec58e361d5c1b4c735eba4.jpg

 

Скрытый текст

photo_2019-01-10_13-08-35.thumb.jpg.f1966146d3a192ce834cc9799d935ac4.jpg

 

*Некоторые кастомные и официальные прошивки Bitmain не считывают количество оборотов на стадии тестов или вовсе не проверяют наличие вентиляторов (кастомные), информацию можно будет увидеть только в веб интерфейсе.

Ссылка на комментарий
Поделиться на другие сайты

  • 1 год спустя...

Вот тут хороший мануал по статусам асика и ошибкам https://hiveos.farm/hiveon-asic-firmware-troubleshooting-asic_statuses_ru

Ссылка на комментарий
Поделиться на другие сайты

  • rammendo изменил название на Fatal Error: Some Fan lost.Проблема с вентилятором

Для публикации сообщений создайте учётную запись или авторизуйтесь

Вы должны быть пользователем, чтобы оставить комментарий

Создать учетную запись

Зарегистрируйте новую учётную запись в нашем сообществе. Это очень просто!

Регистрация нового пользователя

Войти

Уже есть аккаунт? Войти в систему.

Войти
×
×
  • Создать...