Jump to content

kosm_06

Новички
  • Content Count

    6
  • Joined

  • Last visited

Community Reputation

0 Обычный

About kosm_06

  • Rank
    Новичок

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. на включенном майнере отключал вентили, в логе показывал 0 фан, и также ошибка выскакивает, не запускается CG.. Логически рассуждая: рас кулеры раскручиваются на максимум - знач контролька? , мозгов-то у кулеров нет, а контролька гонит на них максимум и сама же говорит. что они на максимуме и вырубает CG..
  2. Люди, у кого M3 в рабочем состоянии, скиньте лог стабильно работы пожалуйста!
  3. @cleopoison накатил 2018. в логе 2 вентиля на максимальных оборотаз и выдает ошибку из-за них получается? ли их отключить вообще и попробовать щапуститься кратковременно? или не стоит рисковать так? мне искать кулеры? Лог Whatsminer M3(прошивка 2018) .txt
  4. по одной плате включал. не помогает, местами кулеры менял, не помогает
  5. Прошился на 2017, не помогла прошивка, что делать?
  6. Здравствуйте всем. Watsminer M3. 3 пятницу подряд вырубается майнинг. Перезагружал, сбрасывал, прошился 20180516 (проработала до перезагрузки) еще не прошивался заводской 2017 в логе вот что, выручайте: Fri Jun 7 11:30:40 2019 local0.warn : Started cgminer 4.9.2 git-6089112 Fri Jun 7 11:30:40 2019 local0.notice : bitmicro_get_power_supply_limit, limit_str:3:000106:8:636:636:636:1:11650:11000:10500:600:0:1:6-4:000107:9:636:636:636:1:11650:11000:10500:600:0:1:6-1:000004:5:576:576:576-2:000105:5:612:612:612 Fri Jun 7 11:30:40 2019 local0.notice : bitmicro_get_power_supply_limit, 3:000106:8:636:636:636:1:11650:11000:10500:600:0:1:6:, count:6, id:3, version:0x106, voltage:8, freq:(636 636 636) Fri Jun 7 11:30:40 2019 local0.notice : params for auto adjusting voltage: enable:1, good HS:11650, HS for sell:11000, HS using highest vol:10500, wait time:600, vol highest:0, vol step:1, freq step:6 Fri Jun 7 11:30:40 2019 local0.notice : bitmicro_get_power_supply_limit, 4:000107:9:636:636:636:1:11650:11000:10500:600:0:1:6:, count:6, id:4, version:0x107, voltage:9, freq:(636 636 636) Fri Jun 7 11:30:40 2019 local0.notice : params for auto adjusting voltage: enable:1, good HS:11650, HS for sell:11000, HS using highest vol:10500, wait time:600, vol highest:0, vol step:1, freq step:6 Fri Jun 7 11:30:40 2019 local0.notice : bitmicro_get_power_supply_limit, 1:000004:5:576:576:576:, count:6, id:1, version:0x4, voltage:5, freq:(576 576 576) Fri Jun 7 11:30:40 2019 local0.notice : bitmicro_get_power_supply_limit, 2:000105:5:612:612:612:, count:6, id:2, version:0x105, voltage:5, freq:(612 612 612) Fri Jun 7 11:30:40 2019 local0.notice : Read power version:0x000106 Fri Jun 7 11:30:40 2019 kern.warn kernel: [ 145.030681] sunxi_i2c_do_xfer()974 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x28) Fri Jun 7 11:30:40 2019 local0.notice : Power voltage has been set to 8 Fri Jun 7 11:30:40 2019 local0.notice : board 0 plug status:0(0: plug, 1: unplug) Fri Jun 7 11:30:40 2019 local0.notice : bitmicro: checking for /dev/ttyS1 Fri Jun 7 11:30:40 2019 local0.notice : SM:0: detected /dev/ttyS1: baud:1000000, chain_num:3, chip_num:63, core_num:100 chip_column_num:3 Fri Jun 7 11:30:40 2019 local0.notice : SM:0: chip_freq_limit:636, work_interval:700, temp_limit:85, voltage_limit:8 Fri Jun 7 11:30:40 2019 local0.notice : SM:0: temp_chips:1, temp_sensors_per_chip:1, upfreq_pass_cores_percent:90, upfreq_pass_chips_percent:95 Fri Jun 7 11:30:40 2019 local0.notice : SM:0: pre_heat_temp:25, pre_heat_timeout:300 Fri Jun 7 11:30:40 2019 local0.notice : board 1 plug status:0(0: plug, 1: unplug) Fri Jun 7 11:30:40 2019 local0.notice : bitmicro: checking for /dev/ttyS2 Fri Jun 7 11:30:40 2019 local0.notice : SM:1: detected /dev/ttyS2: baud:1000000, chain_num:3, chip_num:63, core_num:100 chip_column_num:3 Fri Jun 7 11:30:40 2019 local0.notice : SM:1: chip_freq_limit:636, work_interval:700, temp_limit:85, voltage_limit:8 Fri Jun 7 11:30:40 2019 local0.notice : SM:1: temp_chips:1, temp_sensors_per_chip:1, upfreq_pass_cores_percent:90, upfreq_pass_chips_percent:95 Fri Jun 7 11:30:40 2019 local0.notice : SM:1: pre_heat_temp:25, pre_heat_timeout:300 Fri Jun 7 11:30:40 2019 local0.notice : board 2 plug status:0(0: plug, 1: unplug) Fri Jun 7 11:30:40 2019 local0.notice : bitmicro: checking for /dev/ttyS3 Fri Jun 7 11:30:40 2019 local0.notice : SM:2: detected /dev/ttyS3: baud:1000000, chain_num:3, chip_num:63, core_num:100 chip_column_num:3 Fri Jun 7 11:30:40 2019 local0.notice : SM:2: chip_freq_limit:636, work_interval:700, temp_limit:85, voltage_limit:8 Fri Jun 7 11:30:40 2019 local0.notice : SM:2: temp_chips:1, temp_sensors_per_chip:1, upfreq_pass_cores_percent:90, upfreq_pass_chips_percent:95 Fri Jun 7 11:30:40 2019 local0.notice : SM:2: pre_heat_temp:25, pre_heat_timeout:300 Fri Jun 7 11:30:40 2019 local0.notice : Fan[0] node count 3, node[0](duty:0, speed:680), node[1](duty:60, speed:4050), node[2](duty:100, speed:6000), freq_times_by_speed:30 Fri Jun 7 11:30:40 2019 local0.notice : Fan[1] node count 3, node[0](duty:0, speed:680), node[1](duty:60, speed:4050), node[2](duty:100, speed:6000), freq_times_by_speed:30 Fri Jun 7 11:30:41 2019 local0.notice : Detect fan[0].speed:5790 Fri Jun 7 11:30:41 2019 local0.notice : Detect fan[1].speed:4950 Fri Jun 7 11:30:42 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:30:42 2019 local0.notice : Detect fan[1].speed:4920 Fri Jun 7 11:30:43 2019 local0.notice : Detect fan[0].speed:5790 Fri Jun 7 11:30:43 2019 local0.notice : Detect fan[1].speed:4950 Fri Jun 7 11:30:44 2019 daemon.err system-monitor[1334]: system error state: slot:0, cgminer:0, pool:1, fan:1, temp_sensor:0, temp_over_heat:0, power_supply:0, effective_chips_error:1 Fri Jun 7 11:30:44 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:30:44 2019 local0.notice : Detect fan[1].speed:4920 Fri Jun 7 11:30:45 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:30:45 2019 local0.notice : Detect fan[1].speed:4950 Fri Jun 7 11:30:46 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:30:46 2019 local0.notice : Detect fan[1].speed:4920 Fri Jun 7 11:30:47 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:30:47 2019 local0.notice : Detect fan[1].speed:4950 Fri Jun 7 11:30:48 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:30:48 2019 local0.notice : Detect fan[1].speed:4920 Fri Jun 7 11:30:48 2019 local0.warn : fan[0]:detected max fan speed:5820 < max speed in fan spec:6000, please check params or repair the fan Fri Jun 7 11:30:48 2019 local0.notice : fan[0].max_speed_detected:5820 Fri Jun 7 11:30:48 2019 local0.warn : fan[1]:detected max fan speed:4950 < max speed in fan spec:6000, please check params or repair the fan Fri Jun 7 11:30:48 2019 local0.notice : fan[1].max_speed_detected:4950 Fri Jun 7 11:30:48 2019 local0.err : All fans' detected max speed is less than max speed in its spec, please check params or repair the fans Fri Jun 7 11:30:48 2019 kern.warn kernel: [ 153.069971] cgminer(pid 2432) sending sig 33 to cgminer in cgminer Fri Jun 7 11:30:48 2019 kern.warn kernel: [ 153.077396] cgminer(pid 2432) in cgminer exiting:256 Fri Jun 7 11:30:48 2019 kern.warn kernel: [ 153.083092] cgminer(pid 2464) in cgminer exiting:256 Fri Jun 7 11:30:50 2019 daemon.err system-monitor[1334]: system error state: slot:0, cgminer:1, pool:1, fan:1, temp_sensor:0, temp_over_heat:0, power_supply:0, effective_chips_error:1 Fri Jun 7 11:30:55 2019 daemon.info system-monitor[1334]: No cgminer detected, restart cgminer. Fri Jun 7 11:30:55 2019 kern.warn kernel: [ 160.151208] cgminer(pid 2505) in cgminer exiting:0 Fri Jun 7 11:30:55 2019 kern.warn kernel: [ 160.162744] cgminer(pid 2508) in cgminer exiting:256 Fri Jun 7 11:30:59 2019 kern.warn kernel: [ 164.204546] cgminer(pid 2504) in cgminer exiting:0 Fri Jun 7 11:30:59 2019 local0.warn : Started cgminer 4.9.2 git-6089112 Fri Jun 7 11:30:59 2019 local0.notice : bitmicro_get_power_supply_limit, limit_str:3:000106:8:636:636:636:1:11650:11000:10500:600:0:1:6-4:000107:9:636:636:636:1:11650:11000:10500:600:0:1:6-1:000004:5:576:576:576-2:000105:5:612:612:612 Fri Jun 7 11:30:59 2019 local0.notice : bitmicro_get_power_supply_limit, 3:000106:8:636:636:636:1:11650:11000:10500:600:0:1:6:, count:6, id:3, version:0x106, voltage:8, freq:(636 636 636) Fri Jun 7 11:30:59 2019 local0.notice : params for auto adjusting voltage: enable:1, good HS:11650, HS for sell:11000, HS using highest vol:10500, wait time:600, vol highest:0, vol step:1, freq step:6 Fri Jun 7 11:30:59 2019 local0.notice : bitmicro_get_power_supply_limit, 4:000107:9:636:636:636:1:11650:11000:10500:600:0:1:6:, count:6, id:4, version:0x107, voltage:9, freq:(636 636 636) Fri Jun 7 11:30:59 2019 local0.notice : params for auto adjusting voltage: enable:1, good HS:11650, HS for sell:11000, HS using highest vol:10500, wait time:600, vol highest:0, vol step:1, freq step:6 Fri Jun 7 11:30:59 2019 local0.notice : bitmicro_get_power_supply_limit, 1:000004:5:576:576:576:, count:6, id:1, version:0x4, voltage:5, freq:(576 576 576) Fri Jun 7 11:30:59 2019 local0.notice : bitmicro_get_power_supply_limit, 2:000105:5:612:612:612:, count:6, id:2, version:0x105, voltage:5, freq:(612 612 612) Fri Jun 7 11:30:59 2019 local0.notice : Read power version:0x000106 Fri Jun 7 11:31:00 2019 kern.warn kernel: [ 164.274889] sunxi_i2c_do_xfer()974 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x28) Fri Jun 7 11:31:00 2019 local0.notice : Power voltage has been set to 8 Fri Jun 7 11:31:00 2019 local0.notice : board 0 plug status:0(0: plug, 1: unplug) Fri Jun 7 11:31:00 2019 local0.notice : bitmicro: checking for /dev/ttyS1 Fri Jun 7 11:31:00 2019 local0.notice : SM:0: detected /dev/ttyS1: baud:1000000, chain_num:3, chip_num:63, core_num:100 chip_column_num:3 Fri Jun 7 11:31:00 2019 local0.notice : SM:0: chip_freq_limit:636, work_interval:700, temp_limit:85, voltage_limit:8 Fri Jun 7 11:31:00 2019 local0.notice : SM:0: temp_chips:1, temp_sensors_per_chip:1, upfreq_pass_cores_percent:90, upfreq_pass_chips_percent:95 Fri Jun 7 11:31:00 2019 local0.notice : SM:0: pre_heat_temp:25, pre_heat_timeout:300 Fri Jun 7 11:31:00 2019 local0.notice : board 1 plug status:0(0: plug, 1: unplug) Fri Jun 7 11:31:00 2019 local0.notice : bitmicro: checking for /dev/ttyS2 Fri Jun 7 11:31:00 2019 local0.notice : SM:1: detected /dev/ttyS2: baud:1000000, chain_num:3, chip_num:63, core_num:100 chip_column_num:3 Fri Jun 7 11:31:00 2019 local0.notice : SM:1: chip_freq_limit:636, work_interval:700, temp_limit:85, voltage_limit:8 Fri Jun 7 11:31:00 2019 local0.notice : SM:1: temp_chips:1, temp_sensors_per_chip:1, upfreq_pass_cores_percent:90, upfreq_pass_chips_percent:95 Fri Jun 7 11:31:00 2019 local0.notice : SM:1: pre_heat_temp:25, pre_heat_timeout:300 Fri Jun 7 11:31:00 2019 local0.notice : board 2 plug status:0(0: plug, 1: unplug) Fri Jun 7 11:31:00 2019 local0.notice : bitmicro: checking for /dev/ttyS3 Fri Jun 7 11:31:00 2019 local0.notice : SM:2: detected /dev/ttyS3: baud:1000000, chain_num:3, chip_num:63, core_num:100 chip_column_num:3 Fri Jun 7 11:31:00 2019 local0.notice : SM:2: chip_freq_limit:636, work_interval:700, temp_limit:85, voltage_limit:8 Fri Jun 7 11:31:00 2019 local0.notice : SM:2: temp_chips:1, temp_sensors_per_chip:1, upfreq_pass_cores_percent:90, upfreq_pass_chips_percent:95 Fri Jun 7 11:31:00 2019 local0.notice : SM:2: pre_heat_temp:25, pre_heat_timeout:300 Fri Jun 7 11:31:00 2019 local0.notice : Fan[0] node count 3, node[0](duty:0, speed:680), node[1](duty:60, speed:4050), node[2](duty:100, speed:6000), freq_times_by_speed:30 Fri Jun 7 11:31:00 2019 local0.notice : Fan[1] node count 3, node[0](duty:0, speed:680), node[1](duty:60, speed:4050), node[2](duty:100, speed:6000), freq_times_by_speed:30 Fri Jun 7 11:31:01 2019 local0.notice : Detect fan[0].speed:5760 Fri Jun 7 11:31:01 2019 local0.notice : Detect fan[1].speed:4920 Fri Jun 7 11:31:02 2019 local0.notice : Detect fan[0].speed:5790 Fri Jun 7 11:31:02 2019 local0.notice : Detect fan[1].speed:4950 Fri Jun 7 11:31:03 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:31:03 2019 local0.notice : Detect fan[1].speed:4920 Fri Jun 7 11:31:03 2019 daemon.err system-monitor[1334]: system error state: slot:0, cgminer:0, pool:1, fan:1, temp_sensor:0, temp_over_heat:0, power_supply:0, effective_chips_error:1 Fri Jun 7 11:31:04 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:31:04 2019 local0.notice : Detect fan[1].speed:4950 Fri Jun 7 11:31:05 2019 local0.notice : Detect fan[0].speed:5790 Fri Jun 7 11:31:05 2019 local0.notice : Detect fan[1].speed:4920 Fri Jun 7 11:31:06 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:31:06 2019 local0.notice : Detect fan[1].speed:4950 Fri Jun 7 11:31:07 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:31:07 2019 local0.notice : Detect fan[1].speed:4920 Fri Jun 7 11:31:08 2019 local0.notice : Detect fan[0].speed:5820 Fri Jun 7 11:31:08 2019 local0.notice : Detect fan[1].speed:4950 Fri Jun 7 11:31:08 2019 local0.warn : fan[0]:detected max fan speed:5820 < max speed in fan spec:6000, please check params or repair the fan Fri Jun 7 11:31:08 2019 local0.notice : fan[0].max_speed_detected:5820 Fri Jun 7 11:31:08 2019 local0.warn : fan[1]:detected max fan speed:4950 < max speed in fan spec:6000, please check params or repair the fan Fri Jun 7 11:31:08 2019 local0.notice : fan[1].max_speed_detected:4950 Fri Jun 7 11:31:08 2019 local0.err : All fans' detected max speed is less than max speed in its spec, please check params or repair the fans Fri Jun 7 11:31:08 2019 kern.warn kernel: [ 172.309622] cgminer(pid 2527) sending sig 33 to cgminer in cgminer Fri Jun 7 11:31:08 2019 kern.warn kernel: [ 172.316945] cgminer(pid 2527) in cgminer exiting:256 Fri Jun 7 11:31:08 2019 kern.warn kernel: [ 172.322519] cgminer(pid 2560) in cgminer exiting:256 Плата управления, хеш платы? При включении кулеры на максимуме, и не понижаются обороты, продуться не может.
  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...